Programming track numbers
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
1While playback is stopped, select a track with
or §
§
.
2Press PROGRAM to store the track.
yprogram lights up; the track number
programmed and Pwith the total number of
stored tracks are displayed.
3Select and store all desired tracks in this way.
4Press 2; to start playback of your selected tracks.
yprogram is shown and playback starts.
•You can review the program by pressing PROGRAM
for more than 2 seconds.
yThe display shows all the stored tracks in
sequence.
Notes: – If you press PROGRAM and there is no track selected, SEL is
displayed.
– If you try to store more than 30 tracks, FULL is displayed.
Clearing the program
•While playback is stopped, press STOP to clear
program.
yCLRis displayed once, program goes off,
and the program is cleared.
Note: The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.
RESUME and HOLD
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the OFF–RESUME–HOLD slider for these functions.
RESUME – continuing from where you have stopped
1Switch the slider to RESUME during playback to activate RESUME.
yresume is shown.
2Press STOP whenever you want to stop playback.
3Press 2; whenever you want to resume playback.
yresume is shown and playback continues
from where you have stopped.
•To deactivate RESUME, switch the slider to OFF.
yresume goes off.
HOLD – locking all buttons
This model offers a double lock function to prevent buttons from being
accidentally pressed and activated. You can choose to lock all buttons on
either your set, remote control or even both! Simply adjust the respective
HOLD slider to HOLD on or off position as desired. For example :
1Switch the OFF–RESUME–HOLD slider to HOLD to activate HOLD on the set.
yAll buttons are locked and HOLd is shown
when you press any button.on the set If the set
is switched off, HOLd will be shown only
when 2; is pressed.
2To deactivate HOLD, switch the slider to OFF.
Note: – If you deactivate HOLD by switching the slider
on the set to RESUME, you will be activating the RESUME function.
– No HOLd display indication is available if you have activated the
HOLD command on the remote control.
FEATURES
Selecting different playing possibilities <MODE
It is possible to play tracks in random order, to repeat a single track or the entire
CD, and to play the first few seconds of each track.
1Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
yshuffle :All tracks of the CD are played in
random order until all of them have been played
once.
yshuffle repeat all :All tracks of the CD
are played repeatedly in random order.
yrepeat : The current track is played repeatedly .
yrepeat all :The entire CD is played repeatedly .
ySCAN: The first 10 seconds of each of the
remaining tracks are played in sequence.
2Playback starts in the chosen mode after 2 seconds.
•To return to normal playback, press MODE repeatedly until the display shows
no active modes.
ESP / Power Save Mode
With a conventional portable CD-player you might have experienced that the music
stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION
prevents loss of sound caused by light vibrations and shocks. Continuous playback is
ensured. However ESP does not prevent playback interruptions during vigorous running.
It also does not protect the unit against any damage caused by dropping!
The power save mode helps to extend battery lifetime for longer playback.
•Switch the slider to ESP ON during playback to activate the shock protection.
yis shown and the protection is activated.
•To deactivate the shock protection and enter the power save mode, switch the
slider to POWER SAVE.
ygoes off
POWER SAVE
ESP ON
resume
resume
hold
PROGRAM
MODE
repeat all
shuffle
program
program
program
PROGRAM
DBB
vol
FEATURES
Selecting a track and searching
Selecting a track during playback
•Briefly press or §
§
§
§
once or several times to skip to
the current, previous or next track.
yPlayback continues with the selected track, and
the track’s number is displayed.
Selecting a track when playback is stopped
1Briefly press or §once or several times to select
the desired track. The track number is displayed.
2Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1Keep or §pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
2Release the button when you reach the desired passage.
yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
