Philips AZ1080/00 User manual

AZ 1080
AZ 1081
CD Soundmachine Audio
Audio
AZ1080/00A 03/13/02 10:06 Page 1

2
English
Mains plug
This apparatus is fitted with an approved
moulded 13 Amp plug.To change a fuse in this
type of plug proceed as follows:
1Remove fuse cover and fuse.
2Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place. If the mains plug contains
a fuse, this should have a value of 5 Amp. If a
plug without a fuse is used, the fuse at the
distribution board should not be greater than 5
Amp.
Note:The severed plug must be disposed to avoid
a possible shock hazard should it be inserted into
a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N), brown =
live (L).
• As these colours may not correspond with the
colour markings identifying the terminals in your
plug, proceed as follows:
• Connect the blue wire to the terminal
marked N or coloured black.
• Connect the brown wire to the terminal
marked L or coloured red.
• Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath of
the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
Important notes for users in the U.K. Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt; skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio AZ 1080, AZ 1081
Philips risponde alle prescrizioni dell’art. 2
comma 1 del D. M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2,
5616 JB Eindhoven,The Netherlands
AZ1080/00A 03/13/02 10:06 Page 2

3
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
A
C
M
A
I
N
S
~
B
A
S
S
R
E
F
L
E
X
S
P
E
A
K
E
R
S
Y
S
T
E
M
12 341 5
67 8 90! @
#
$
%
AZ1080/00A 03/13/02 10:06 Page 3

4
English
CAUTION: Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe operation.
This product complies with the radio interference requirements of the European Union.
ATTENTION: L’utilisation des commandes ou réglages ou le non-respect des procédures
ci-incluses peuvent se traduire par une exposition dangereuse à l’irradiation.
Ce matériel satisfait aux impératifs de brouillage radio de la Communauté Européenne.
ATENCIÓN: El uso de mandos o ajustes o la ejecucción de métodos que no sean los
aquí descritos puede ocasionar peligro de exposición a radiación.
Este aparato satisface las normas relativas a la interferencia radioeléctrica de la
Comunidad Europea.
ACHTUNG: Der Gebrauch von Bedienelemente oder Einstellungen bzw.
Verfahrensausführungen die hier nicht ausdrücklich erwähnt worden sind, kann eine
gefährliche Strahlendosierung oder andere unsichere Operationen zur Folge haben.
Dieses Produkt entspricht den Funkentstörvorschriften der Europäischen Union.
LET OP: Het gebruik van de toetsen en regelingen of het toepassen van de
aanwijzingen anders dan hier beschreven, kan leiden tot blootstelling aan gevaarlijke
straling of tot onveilige werking.
Dit apparaat voldoet aan de radio-ontstoringseisen van de Europese Unie.
ATTENZIONE: L'uso dei comandi o regolazioni o prestazioni delle procedure oltre a
quelle descritte nel presente potrebbero causare esposizione a radiazioni pericolose
o altre operazioni rischiose.
Questo prodotto è conforme ai requisiti delle interferenze radio della Unione Europea.
AVISO:A utilização de comandos ou ajustes ou a execução de procedimentos de
forma diferente daquela aqui indicada poderá resultar numa exposição perigosa a
radiações ou noutra operação arriscada.
Este produto obedece aos requisitos referentes a interferência de rádio estabelecidos
pela União Europeia.
ADVARSEL:Anvendelse af andre betjeningsanordninger eller justeringer eller
udførelse af andre procedurer end de heri angivne, kan medføre udsættelse for farlig
stråling eller andre risici.
Dette apparat overholder EU's krav vedrørende radiostøj.
VARNING: Om du använder knapparna på annat än här angivet sätt eller utför
andra justeringar eller förfaranden än de här angivna kan du utsättas för skadlig
strålning eller andra risker.
Denna apparat uppfyller EU:s krav beträffande radiostörningar.
MUISTUTUS: Muiden kuin tässä kuvattujen säätimien tai säätöjen tai
toimenpiteiden käyttö voi aiheuttaa vaarallisen altistuksen säteilylle tai muun
turvallisuutta vaarantavan seurauksen.
Tämä tuote on Euroopan unionin radiohäiriöitä koskevien vaatimusten mukainen.
OO: O ,      
          ,    
         .
T            
.
Caution
AZ1080/00A 03/13/02 10:06 Page 4

5
SvenskaSuomi
English_________________6
Français_______________14
Español _______________22
Deutsch_______________30
Nederlands____________38
Italiano _______________46
Português _____________54
Dansk ________________62
Svenska_______________70
Suomi ________________78
 _____________86
Index
English Français Español Deutsch Nederlands Italiano Português Dansk
AZ1080/00A 03/13/02 10:06 Page 5

Meet Philips at the Internet
http://www.philips.com
Printed in China
CLASS 1
LASER PRODUCT
AZ 1080
AZ 1081
English Français Español Deutsch Nederlands Italiano PortuguêsDansk
SvenskaSuomi
3140 115 2936.1
AZ1080/00B 03/13/02 10:09 Page 95

6
English
Top and front panels
1 LIFTTO OPEN – opens/ closes the CD
door
2 Source selector: CD,MW,FM,
TAPE/OFF
– selects CD source of sound, tuner
waveband or tape source of sound
– power on/ off switch
3 CASSETTE RECORDER:
PAUSE ;– pauses recording or playback
STOP•OPEN 9/ – stops the tape; opens
the cassette door
SEARCH 5or 6– fast rewinds / winds
the tape
PLAY 1– starts playback
RECORD 0– starts recording
4 CD display – shows the CD functions
5 TUNING
6 PLAY•PAUSE 2; – starts or pauses CD
playback
7STOP9– stops CD playback
8 SEARCH ∞,§
CD: skips or searches a passage/track
backwards or forward
9 DBB (Dynamic Bass Boost) –
enhances bass response
10 REPEAT – repeats a track/CD
11 SHUFFLE – plays all CD tracks in
random order
12 VOLUME – adjusts volume level
Back Panel
13 Telescopic aerial – to improve FM
reception
14 Battery door – open to insert 6 x 1.5V
R14/UM2/ C-cell batteries
15 AC MAINS – inlet for mains lead
Power Supply
Whenever convenient, use the power
supply if you want to conserve battery life.
Make sure you remove the plug from the
set and wall socket before inserting
batteries.
For users in the U.K.: please follow the
instructions on page 2.
Batteries (not included)
1Open the battery compartment and insert
six batteries, type R-14,UM-2 or C-cells,
(preferably alkaline) with the correct
polarity as indicated by the "+" and "–"
symbols inside the compartment.
2Close the compartment door, and make
sure the batteries are firmly and correctly in
place.The set is now ready to operate.
Batteries contain chemical substances,
so they should be disposed of properly.
Controls Power Supply
A
C
M
A
I
N
S
~
6 x 1.5V R14/ UM2/ C CELL
AZ1080/00A 03/13/02 10:06 Page 6

7
English
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to
burst.Therefore:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1 Check if the mains voltage, as shown on
the type plate located on the bottom
of the set, corresponds to your local
mains supply. If it does not, consult your
dealer or service centre.
2 Connect the mains lead to the AC MAINS
inlet and the wall socket.The mains supply is
now connected and ready for use.
3 To switch off completely, unplug the mains
lead from the wall socket.
• Unplug the mains lead from the wall socket
to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Switching power on/off:
Save energy
Whether you are using mains or battery
supply, to avoid unnecessary energy
consumption always adjust the source
selector to TAPE/OFF and check if the
cassette keys are released.
General operation
1 To select your sound source adjust the
source selector to CD,MW,FM or
TAPE/OFF.
2 Adjust the sound with the VOLUME and
DBB (Dynamic Bass Boost) controls.
3To switch off the set, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.
Power Supply
A
~
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
AZ1080/00A 03/13/02 10:06 Page 7

8
English
Radio reception
1 Adjust the source selector to MW or FM
to select your desired waveband.
2 Tu r n TUNING to tune to a radio station.
To improve reception
– For FM, pull out the telescopic aerial. Incline
and turn the aerial. Reduce its length if the
signal is too strong (very close to a
transmitter).
– For MW the set is provided with a built-in
aerial so the telescopic aerial is not needed.
Direct the aerial by turning the whole set.
3To switch off the radio, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.
CD Player
Display indication for CD functions:
– --: flashes when CD source just selected
– In stop mode: total track number
– During CD playback: 2and current
track number
REPEAT/ REPEAT ALL: when the
respective repeat mode is activated
– SHUFFLE when shuffle active
– Er: no disc/ error in CD operation or
with the CD/ CD-(R) is blank or the disc
is not finalised (seeTroubleshooting)
Playing a CD
1Adjust the source selector to CD.
2To open the CD door, lift the CD door at
the edge marked LIFTTO OPEN.
3Insert a CD or CD-(R) with the printed
side facing up and press the CD door gently
close.
4Press PLAY•PAUSE 2; on the set to
start playback.
5To pause playback press PLAY•PAUSE
2;.To resume, press PLAY•PAUSE 2;
again.
➜2flashes during pause
6To stop CD play, press STOP 9.
7To switch off the set, adjust the source
selector to TAPE/OFF position and check
the cassette keys are released.
Note: CD play will also stop when:
– you open the CD compartment;
– you select MW,FM or TAPE sound
source;
– the CD has reached to the end.
Radio CD-Player
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
AZ1080/00A 03/13/02 10:06 Page 8

9
English
Selecting a different track
During playback you can use the
SEARCH buttons to select a particular
track.
• If you have selected a track number in the
stop or pause position, press
PLAY•PAUSE 2; to start playback.
• Press SEARCH §once briefly for the
next track, or press repeatedly until the
desired track number appears in the display.
• Press SEARCH ∞once briefly to return
to the beginning of a current track.
• Press SEARCH ∞more than once briefly
for a previous track.
Finding a passage within a track
1During playback, press and hold down
SEARCH ∞or §.
• The CD is played at high speed and low
volume.
2When you recognize the passage you want
release the SEARCH button.
➜Normal playback resumes.
Note:When searching within a final track and
you reach the end of the last track, the CD
goes to stop mode.
Play modes
REPEAT can be selected or changed
during playback in the following sequence:
REPEAT – plays the current track
continuously
REPEAT ALL – plays the entire CD
continuously
1During playback, press REPEAT once or
more until the desired REPEAT mode is
shown.
• You can use SEARCH ∞or §to skip
tracks during the repeat modes.
• The REPEAT play options can be
combined and used with shuffle: e.g.
REPEAT ALL SHUFFLE– repeats the
entire CD in random order.
2To return to normal playback press
REPEAT until the REPEAT modes are no
longer shown.
• You can also press STOP 9to quit the
play mode.
3During playback, press SHUFFLE once.
• All tracks are played in random order.
CD-Player
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
AZ1080/00A 03/13/02 10:06 Page 9

10
English
CASSETTE RECORDER
Cassette playback
1Adjust the source selector to TAPE/OFF.
2Press STOP•OPEN 9/ to open the
cassette door and insert a recorded
cassette.
3Close the cassette door.
4Press PLAY 1to start playback.
5To pause playback press PAUSE ;.To
resume, press the key again.
6By pressing SEARCH 5or 6, fast
winding of the tape is possible in both
directions.To stop fast winding, press
STOP•OPEN 9/.
7To stop the tape, press STOP•OPEN 9/.
• The keys are automatically released at the
end of the tape, and the set is switched off,
except if PAUSE ;has been activated.
General information on
recording
• Recording is permissible insofar as copyright
or other rights of third parties are not
infringed.
• This deck is not suited for recording on
CHROME (IEC II) or METAL (IEC IV) type
cassettes. For recording, use only NORMAL
type cassettes (IEC type I) on which the
tabs have not been broken.
•The best recording level is set automatically.
Altering the VOLUME and DBB controls
will not affect the recording in progress.
• At the very beginning and end of the tape,
no recording will take place during the
7 seconds when the leader tape passes the
recorder heads.
• To protect a tape from accidental erasure,
have the tape in front of you and break out
the left tab. Recording on this side is no
longer possible.To record over this side
again, cover the tabs with a piece of
adhesive tape.
Synchro Start CD recording
1Select CD source.
2Insert a CD.
3Press STOP•OPEN 9/ to open the
cassette door. Insert a blank tape.
Cassette Recorder
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
REPEAT
TAP
OFF
MW
FM
CD
L
I
F
T
T
O
O
P
E
N
A
Z
1
0
8
0
C
D
S
O
U
N
D
M
A
C
H
I
N
E
C
D
R
E
W
R
I
T
A
B
L
E
C
O
M
P
A
T
I
B
L
E
S
E
A
R
C
H
S
T
O
P
D
Y
N
A
M
IC BASS
B
O
O
S
T
P
L
A
Y
/
P
A
U
S
E
DBB
S
H
U
F
F
L
E
R
E
P
E
A
T
V
O
L
U
M
E
N
E
P
O
O
T
T
F
I
L
TUNING
CDTRACK
P
L
A
Y
S
T
O
P
•
O
P
E
N
P
A
U
S
E
S
E
A
R
C
H
S
E
A
R
C
H
AZ1080/00A 03/13/02 10:06 Page 10

11
English
4Close the cassette door.
5Press RECORD 0to start recording.
• Playing of the CD starts automatically. It is
not necessary to start the CD player
separately.
6For brief interruptions press PAUSE ;.To
resume recording, press PAUSE ;again.
7To stop recording, press STOP•OPEN 9/.
➜The CD player goes to pause mode.
Press PLAY•PAUSE 2; to resume CD
playback, or press STOP 9to stop CD
play.
Selecting and recording a particular
passage
• During CD playback, press and hold down
the SEARCH buttons ∞or §on the set
to find your passage.
• Press PLAY•PAUSE 2; to put the CD
player on pause at the selected passage.
➜Recording will begin from this exact
point in the track when you press
RECORD 0.
Note: If you press RECORD 0during
playback, recording starts automatically from
the beginning of the current track.
Recording from the Radio
1Adjust the source selector to MW or FM to
select your desired waveband.
2Tune to the desired radio station (see
Radio reception).
3Press STOP•OPEN 9/ to open the
cassette door. Insert a blank tape.
4Close the cassette door.
5Press RECORD 0to start recording.
6For brief interruptions, press PAUSE ;.To
resume recording, press PAUSE ;again.
7To stop recording,
press STOP•OPEN 9/ .
Environmental information
All unnecessary packaging material has
been omitted.The packaging can be
easily separated into three materials:
cardboard, polystyrene and plastic.
Your set consists of materials which can
be recycled if disassembled by a
specialized company. Please observe the
local regulations regarding the disposal
of packing materials, exhausted
batteries and old equipment.
Recording
AZ1080/00A 03/13/02 10:06 Page 11

12
English
Precautions &
General Maintenance
• Place the set on a hard and flat surface so
that the system does not tilt.
• Do not expose the set, batteries, CDs or
cassettes to humidity, rain, sand or excessive
heat caused by heating equipment or direct
sunlight.
• Do not cover the set.Adequate ventilation
with a minimum gap of 6 inches between
the ventilation holes and surrounding
surfaces is necessary to prevent heat build-
up.
• The mechanical parts of the set contain
self-lubricating bearings and must not be
oiled or lubricated.
• To clean the set, use a soft, slightly
dampened chamois leather. Do not use any
cleaning agents containing alcohol,
ammonia, benzene or abrasives as these
may harm the housing.
Tape deck maintenance
To ensure quality recording and playback of
the tape deck, clean parts A,Band C
shown in the diagram below, after approx.
50 hours of operation, or on average once
a month. Use a cotton bud slightly
moistened with alcohol or a special head
cleaning fluid to clean the deck.
1Open the cassette door by pressing
STOP•OPEN 9/.
2Press PLAY 1and clean the rubber
pressure roller C.
3Press PAUSE ;and clean the magnetic
heads A, and also the capstan B.
4After cleaning, press STOP•OPEN 9/.
– Cleaning of the heads can also be done by
playing a cleaning cassette through once.
CD player and CD handling
• The lens of the CD player should never be
touched!
• Sudden changes in the surrounding
temperature can cause condensation to
form and the lens of your CD player to
cloud over. Playing a CD is then not
possible. Do not attempt to clean the lens
but leave the set in a warm environment
until the moisture evaporates.
• Use only Digital Audio CDs.
• Always close the CD door to keep the CD
compartment dust-free.To clean, dust the
compartment with a soft dry cloth.
• To take a CD out of its box, press the
centre spindle while lifting the CD. Always
pick up the CD by the edge and replace
the CD back in its box after use to avoid
scratching and dust.
• To clean the CD, wipe in a straight line from
the centre towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
•Never write on a CD or attach any stickers
to it.
Maintenance
AB
C
AZ1080/00A 03/13/02 10:06 Page 12

13
English
If a fault occurs, first check the points listed below before taking the set for repair. Do
not open the set as there is a risk of electric shock.
If you are unable to remedy a problem by following these hints, consult your dealer or
service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this
will invalidate the guarantee.
Troubleshooting
Problem Solution
No sound – Adjust theVOLUME
No power – Mains lead not securely connected.
Connect AC mains lead properly
– Batteries exhausted /incorrectly inserted.
Insert (fresh) batteries correctly
Display does not function – Electrostatic discharge
properly/ No reaction to Switch off and unplug the set. Reconnect after a few
operation of any of the seconds.
controls
Er indication – No CD inserted, insert a CD
– CD badly scratched/ dirty.
Replace/ clean CD (see maintenance)
– CD-R(W) is blank or the disc is not finalized.
Use a finalized CD-R(W)
– Laser lens steamed up.
Wait until lens has cleared/acclimatized
CD playback does not work – CD badly scratched/ dirty.
Replace/ clean CD (see maintenance)
The CD skips tracks – CD damaged or dirty. Replace or clean CD.
– Shuffle is active. Quit shuffle mode
Poor cassette sound quality – Dust and dirt on the heads, etc.
Clean deck parts, see maintenance.
– Use of incompatible cassette types (METAL or
CHROME). Only use NORMAL (IEC I) for recording
Recording does not work – Cassette tab(s) may be broken.Apply a piece of
adhesive tape over the missing tab space.
AZ1080/00A 03/13/02 10:06 Page 13