Philips HQ489 User manual

ENGLISH 4
BAHASA MELAYU 15
INDONESIA 26
TI”NG VI◊T 37
 48
59
70
80
HQ489, HQ481

Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗Only use the mains cord supplied.
◗Do not use a damaged mains cord.
◗If the mains cord is damaged, always have it
replaced by one of the original type in order
to avoid a hazard.
◗The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages ranging from 100 to 240 volts.
◗Charge, store and use the appliance at a
temperature between 5cC and 35cC.
◗Do not recharge the shaver in a closed pouch.
C◗Keep the appliance and the mains cord dry.
Charging
Make sure the appliance is switched off before
you start charging it.
When you charge the shaver for the first time or
after a long period of disuse, let it charge
continously for 4 hours. Charging normally takes
approx. 1 hour.
You can also shave without charging by
connecting the shaver to the mains.
Do not leave the appliance connected to the
mains for more than 24 hours.
ENGLISH4

Charge indications
Charging
C◗As soon as you start charging the empty
shaver, the green pilot light goes on.
Battery fully charged
C◗When the battery has been fully charged, the
green pilot light starts blinking.
Charging the appliance
Charge the appliance when the motor stops or
starts running slower.
Do not recharge the shaver in a closed pouch.
C1Put the appliance plug in the shaver.
2Put the mains plug in the wall socket.
3Remove the mains plug from the wall
socket and pull the appliance plug out of
the shaver when the battery has been fully
charged.
ENGLISH 5
CHARGE
CHARGE

Cordless shaving time
A fully charged shaver has a cordless shaving time
of up to 30 minutes.
Using the appliance
Shaving
C1Switch the appliance on by pressing the
switch lock (1) and pushing the on/off slide
upwards (2).
BThe switch lock prevents accidental switching on of
the appliance.
C2Move the shaving heads quickly over your
skin, making both straight and circular
movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3Switch the shaver off by pushing the on/off
slide downwards.
C4Put the protection cap on the shaver every
time you have used it, to prevent damage.
ENGLISH6

Trimming
For grooming sideburns and moustache.
C1Open the trimmer by pushing the slide
upwards.
The trimmer can be activated while the motor is
running.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
C◗For easy and optimal cleaning, the Philips
Action Clean (shaving head cleaner, type
HQ100) is available.Ask your Philips dealer
for information.
BThe Philips Action Clean may not be available in
all countries. Contact the Customer Care Centre in
your country about the availability of this
accessory.
You can also clean the shaver in the following
way:
Every week: shaving unit and hair chamber
1Switch the shaver off, remove the mains
plug from the wall socket and pull the
appliance plug out of the shaver.
C2Clean the top of the appliance first, using
the brush supplied.
ENGLISH 7

C3Press the release button (1) and remove
the shaving unit (2).
C4Clean the inside of the shaving unit and the
hair chamber with the brush.
C5Put the shaving unit back onto the shaver.
Every two months: shaving heads
1Switch the shaver off, remove the mains
plug from the wall socket and pull the
appliance plug out of the shaver.
C2Press the release button (1) and remove
the shaving unit (2).
C3Remove the retaining frame by pushing the
sides of the central spring towards each
other (1) and lifting the retaining frame out
of the shaving unit (2).
ENGLISH8

C4Slide the shaving heads out of the retaining
frame and clean them one by one.
Do not mix up the cutters and the guards.
This is essential since each cutter has been
ground with its corresponding guard for optimal
performance. If you accidentally mix the sets up, it
could take several weeks before optimal shaving
performance is restored.
C5Clean the cutter with the short-bristled
side of the brush.
Brush carefully in the direction of the arrow.
C6Brush the guard.
C7Slide the shaving heads back into the
retaining frame and put the retaining frame
back into the shaving unit.
8Put the shaving unit back onto the shaver.
For extra thorough cleaning, clean the shaving
heads by putting them in a degreasing liquid (e.g.
alcohol) every six months.To remove the shaving
heads, follow steps 1 to 4 described above. After
cleaning, lubricate the central point on the inside
of the guards with a drop of sewing machine oil
to prevent wear of the shaving heads.
ENGLISH 9

Trimmer
Clean the trimmer every time you have used it.
1Switch the shaver off, remove the mains
plug from the wall socket and pull the
appliance plug out of the shaver.
C2Clean the trimmer with the brush
supplied.
C3Lubricate the trimmer teeth with a drop
of sewing machine oil every six months.
Storage
C◗Put the protection cap on the shaver to
prevent damage.
◗The appliance can be stored in the luxury
pouch supplied.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with
HQ4«Philips shaving heads only.
ENGLISH10

1Switch the shaver off, remove the mains
plug from the wall socket and pull the
appliance plug out of the shaver.
C2Press the release button (1) and remove
the shaving unit (2).
C3Remove the retaining frame by pushing the
sides of the central spring towards each
other (1) and lifting the retaining frame out
of the shaving unit (2).
C4Slide the shaving heads out of the retaining
frame.
C5Slide new shaving heads into the retaining
frame.
C6Put the retaining frame back into the
shaving unit.
7Put the shaving unit back onto the shaver.
ENGLISH 11

Accessories
The following accessories are available:
- HQ4«Philips shaving heads.
- HQ100 Philips Action Clean
(shaving head cleaner).
- HQ101 Philips Action Clean refill
(shaving head cleaning liquid).
- HQ110 Philips shaving head cleaner
(shaving head cleaning spray).
Environment
C◗Do not throw the appliance away with the
normal household waste at the end of its life,
but hand it in at an official collection point for
recycling. By doing this you will help to
preserve the environment.
The built-in rechargeable battery contains
substances that may pollute the environment.
Always remove the battery before discarding the
appliance or handing it in at an official collection
point. Dispose of the battery at an official
collection point for batteries. If you have trouble
removing the battery, you can also take the
appliance to a Philips service centre, which will
remove the battery for you and will dispose of it
in an environmentally safe way.
ENGLISH12

Disposal of the battery
Only remove the battery if it is completely empty.
1Remove the mains plug from the wall
socket and pull the appliance plug out of
the shaver.
C2Let the shaver run until it stops, undo the
screws and open the shaver.
3Remove the battery.
Do not connect the shaver to the mains again
after the battery has been removed.
Guarantee & service
If you need information or if you have a problem,
please visit the Philips website at www.philips.com
or contact the Philips Customer Care Centre in
your country (you will find its phone number in
the worldwide guarantee leaflet). If there is no
Customer Care Centre in your country, turn to
your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and
Personal Care BV.
Troubleshooting
1Reduced shaving performance
BCause 1: the shaving heads are dirty.
ENGLISH 13

BThe shaver has not been cleaned well enough or
has not been cleaned for a long time.
◗Clean the shaver thoroughly before you
continue shaving. See chapter 'Cleaning and
maintenance'.
BCause 2: long hairs are obstructing the shaving
heads.
◗Clean the cutters and guards with the brush
supplied. See chapter 'Cleaning and
maintenance', section 'Every two months:
shaving heads'.
BCause 3: the shaving heads are damaged or worn.
Replace the shaving heads. See chapter
'Replacement'.
2The shaver does not work when the on/off
slide is pushed upwards.
BCause 1: the battery is empty.
◗Recharge the battery. See chapter 'Charging'.
BCause 2: the shaver is not connected to the mains.
◗Put the mains plug in the wall socket.
ENGLISH14

Penting
Baca arahan penggunaan ini dengan teliti sebelum
menggunakan perkakas dan simpan untuk rujukan
di masa depan.
◗Gunakan kord sesalur yang dibekalkan sahaja.
◗Jangan gunakan kord sesalur yang rosak.
◗Jika kord sesalur rosak, hanya gantikan dengan
jenis original bagi mengelakkan bahaya.
◗Perkakas dilengkapi dengan pemilih voltan
automatik dan sesuai untuk voltan punca
kuasa utama antara 100 hingga 240 volt
◗Cas, simpan dan gunakan perkakas pada suhu
antara 5cC dan 35cC.
◗Jangan mengecas semula pencukur di dalam
pau tertutup.
C◗Pelihara agar perkakas dan kord kuasa kering.
Mengecas
Pastikan perkakas dimatikan sebelum dicas.
Apabila anda mengecas pencukur buat pertama
kali atau setelah lama tidak digunakan, biarkan ia
dicas berterusan selama 4 jam. Pengecasan
biasanya mengambil masa 1 jam.
Anda juga dapat bercukur tanpa mengecas
dengan menyambungkan pencukur kepada punca
kuasa utama.
Jangan biarkan perkakas dipasang pada sesalur
kuasa selama lebih daripada 24 jam.
BAHASA MELAYU 15

Arahan cas
Mengecas
C◗Sebaik sahaja anda mula mengecas pencukur
yang kosong, lampu panduan hijau akan
menyala.
Bateri yang sudah dicas sepenuhnya.
C◗Apabila bateri telah dicas sepenuhnya, lampu
panduan hijau akan mula berkelip.
Mengecas perkakas
Cas perkakas apabila motor berhenti atau menjadi
semakin lambat.
Jangan mengecas semula pencukur di dalam pau
tertutup.
C1Pasangkan plag perkakas pada alat
pencukur.
2Masukkan plag utama ke dalam soket.
3Cabutkan plag sesalur dari soket dinding
dan tarik keluar plag perkakas dari
BAHASA MELAYU16
CHARGE
CHARGE

pencukur apabila bateri telah dicaskan
sepenuhnya.
Masa pencukuran tanpa kord
Pencukur yang dicas penuh ada masa pencukuran
tanpa kord sehingga kira-kira 30 minit.
Menggunakan perkakas
Pencukuran
C1Hidupkan perkakas dengan menekan kunci
suis (1) dan menggelongsorkan punat
on/off ke atas (2).
BKunci suis mengelakkan perkakas dari dihidupkan
dengan tidak sengaja.
C2Gerakkan kepala pencukur denagn gerakan
lurus dan membulat di atas permukaan
kulit dengan pantas.
Hasil pencukuran yang terbaik akan terhasil jika
muka anda kering.
Kulit anda mungkin memerlukan 2 atau 3 minggu
untuk membiasakan diri dengan sistem Philips.
3Matikan pencukur dengan
menggelongsorkan punat mati/hidup ke
bawah.
C4Pasang semula penutup pelindung pada
pencukur setelah setiap penggunaan untuk
mengelakkan kerosakan.
BAHASA MELAYU 17

Perapian
Untuk merapikan jambang dan kumis kemas.
C1Buka perapi dengan menolak selak ke atas.
Perapi dapat dihidupkan semasa motor berjalan.
Pembersihan dan penyenggaraan
Membersih alat pencukur dengan kerapkali
menjamin prestasi pencukuran terbaik.
C◗Pembersih Tindakan Bersih Philips (bahan
pembersih kepala pencukur, jenis HQ100)
boleh didapati untuk pembersihan yang mudah
dan optimum. Untuk mendapatkan maklumat
lanjut, sila hubungi penjual Philips.
BPembersih Tindakan Bersih Philips mungkin tidak
terdapat di semua negara. Hubungi Pusat
Khidmat Pelanggan di negeri anda untuk
mengetahui tentang ketersediaan aksesori ini.
Anda juga boleh membersihkan pencukur dengan
cara yang berikut:
Setiap minggu: unit pencukur dan ruang
rambut
1Matikan pencukur, cabut plag kuasa dari
soket dinding dan tarik keluar plag
perkakas dari pencukur.
BAHASA MELAYU18

C2Bersihkan bahagian atas perkakas dahulu
dengan berus yang dibekalkan.
C3Tekan butang pelepas (1) dan tanggalkan
unit pencukur (2).
C4Bersihkan bahagian dalam unit cukur dan
ruang rambut dengan berus.
C5Kembalikan unit pencukur kepada
pencukur.
Setiap dua bulan: kepala pencukur
1Matikan pencukur, cabut sesalur utama dari
soket dinding dan tarik keluar plag
perkakas dari pencukur.
C2Tekan butang pelepas (1) dan tanggalkan
unit pencukur (2).
BAHASA MELAYU 19

C3Tanggalkan rangka penahan dengan
menolak bahagian tepi spring tengah ke
arah masing-masing (1) dan angkat rangka
penahan dari unit pencukur (2).
C4Luncur keluarkan kepala pencukur dari
rangka penahan dan bersihkannya satu per
satu.
Jangan campur adukkan pemotong dan adang
yang berlainan set.
Ini penting kerana tiap pemotong diasah dengan
adang sepadan untuk mendapatkan pencapaian
optimum. Prestasi pencukuran optimum mungkin
mengambil masa beberapa minggu untuk
dipulihkan sekiranya anda mencampur-adukkan
pemotong dan adang tersebut dengan tidak
sengaja.
C5Bersihkan pemotong dengan tepi berus
yang berbulu pendek.
Berus ke arah anak panah dengan berhati-hati.
C6Berus adangan.
C7Gelongsorkan kepala pencukur balik ke
dalam rangka penahan dan pasangkan
semula rangka penahan itu ke unit
pencukur.
8Kembalikan unit pencukur kepada
pencukur.
BAHASA MELAYU20

Untuk pembersihan tambahan yang menyeluruh,
bersihkan kepala pencukur dengan meletakkannya
ke dalam cecair nyahgris (contohnya alkohol)
setiap enam bulan. Untuk menanggalkan kepala
pencukur, ikuti langkah 1 hingga 4 seperti yang
dihuraikan di atas. Setelah dibersihkan, lenserkan
bahagian tengah di dalam adangan dengan setitik
minyak mesin jahit untuk mengelak kepala
pencukur menjadi haus.
Perapi
Bersihkan perapi setiap kali anda
menggunakannya.
1Matikan pencukur, cabut plag kuasa dari
soket dinding dan tarik keluar plag
perkakas dari pencukur.
C2Bersihkan perapi dengan berus yang
dibekalkan.
C3Lincirkan gigi perapi setiap enam bulan
dengan setitik minyak mesin jahit.
Penyimpanan
C◗Pasangkan kembali penutup perlindungan pada
alat pencukur untuk mengelakkan kerosakan.
◗Perkakas boleh disimpan di dalam beg kecil
yang disediakan.
BAHASA MELAYU 21

Penggantian
Gantikan kepala pencukur setiap dua tahun sekali
untuk mendapatkan hasil pencukuran yang
optimum.
Gantikan kepala pencukur yang rosak atau haus
dengan «Philips HQ4 kepala pencukur sahaja.
1Matikan pencukur, cabut plag utama dari
soket dinding dan tarik keluar plag
perkakas dari pencukur.
C2Tekan butang pelepas (1) dan tanggalkan
unit pencukur (2).
C3Tanggalkan rangka penahan dengan
menolak bahagian tepi spring tengah ke
arah masing-masing (1) dan angkat rangka
penahan dari unit pencukur (2).
C4Luncur keluarkan kepala pencukur dari
rangka penahan.
C5Luncurkan kepala pencukur baru ke dalam
rangka penahan.
BAHASA MELAYU22