1Connect
A
Placement
Proper speakers system placement is important to
ensure optimum sound performance.
APlace the Sound Bar system at the normal listening
ear-level, or at least above the knee-level. Face it
straight ahead towards the listening area.
BPlace the subwoofer on the floor, at least one metre
away from the TV.
B
Preparing for rear connections
APush up the catches to lift up the rear cover.
BConnect the required cables and direct all the cables
to the CABLE OUT point (see the following sections
for details).
Note All the cables must be placed properly inside
the rear panel in order for the rear cover to close.
2Set up
C
Connect the Sound Bar system and
subwoofer
TOMAIN UNIT
Am/MW
FM/AM/MWANTENNA
SPEAKERS
COAXIAL
DIGITALIN
AUX1 AUX2
RIGHT LEFT
FM75
R
L
MAINS
zConnect the TO MAIN UNIT cable from the
subwoofer to the rear of the main unit. One end
connect to TO SUBWOOFER socket and another
end connect to LOUDSPEAKERS socket.
D
Connect the main unit to TV
zConnect a scart cable (supplied) from the
SCART OUT (TV1) socket on the main unit to the
SCART IN socket on your TV.
OR
zIf your TV supports HDMI, connect the HDMI cable
(not supplied) from the HDMI OUT to the HDMI IN
socket on your TV.
Note It is important to connect the main unit
directly to your TV.
A
Finding the viewing channel
APress 2(STANDBY ON) on the main unit to turn
it on.
BTurn on the TV. Use the TVs remote control to
select the correct viewing channel.
Note To search for the correct viewing channel,
press the Channel Down button on the TVs remote
control repeatedly (or AV, SELECT, °button) until
you see the Video In channel.
B
Setting up the speakers
When you turn on this unit for the rst time, the
speaker setup message appears on the TV. Follow the
on-screen instructions to complete the setup.
The next few steps will help you set up your
Ambisound home theater system to match your
listening environment.
Stop: Exit Continue
Welcome
APress cursor right key on the remote control to
access Sound Bar system setup.
BWhen the { Orientation } screen appears, press
cursor right key to continue.
CSelect a most suitable predefined setting according
to your room environment and setup, press cursor
right key to confirm and go to the next screen.
{ Room Acoustics }
Select the type of walls that surround your room.
The default setting is ‘Hard (concrete, wood)’.
{ Room Placement }
Select the Sound Bar system’s placement position in
your room. The default setting is ‘Middle’.
{ Height }
Select the height at which the Sound Bar system is
placed. The default setting is between 0.8~1.2 metres.
{ Distance }
Select the distance between the listening position and
the Sound Bar system. The default setting is between
2~3 metres.
DWhen the { Complete } screen appears, press
cursor right key to exit.
Note Refer to the accompanying user manual
for other setup options.
E
Connect the radio antennas and
power cable
Keep the antennas away from the electronic devices to
prevent unwanted interference.
TOMAIN UNIT
MW
FM/MWANTENNA
SPEAKERS
COAXIAL
DIGITALIN
AUX1 AUX2
RIGHT LEFT
FM75
R
L
MAINS
A
B
FM 75
C
AConnect the FM antenna to the inner pin of the
FM 75 socket. Extend the antenna for optimum
reception.
BUnfold the AM/MW loop antenna and fix the claw
into the slot. Push the tabs and insert the wires into
the AM/MW sockets
CConnect the power cable from subwoofer to the AC
power outlet.
F
Connect audio output from other
device (optional)
Use a red and white audio cables (not supplied) to
connect the AUDIO IN-AUX1 or AUX2 sockets on the
subwoofer to the AUDIO OUT sockets on the
connected device (for example, DVD recorder, VCR,
Cable/Satellite Box).
AM/MW
FM/AM/MWANTENNA
TOMAIN UNIT
SPEAKERS
COAXIAL
DIGITALIN
AUX1 AUX 2
RIGHT LEFT
FM75
R
L
MAINS
Note Press AUX on the remote control to
select ‘AUX1’ or ‘AUX2’ as the source you want to
listen to.
Television
( rear)
Subwoofer (rear)
DVD recorder/
VCR/ Cable/
Satellite Box
Subwoofer (rear)
Main unit (rear)
Main unit (rear)
Subwoofer (rear) FM antenna
AM/MW
antenna
or
