Philips 2AANUBT50 User manual

www.philips.com/support
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips

1EN
Contents
1 Important 2
Important safety instructions 2
2 Your portable speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 3
3 Get started 4
Charge the built-in battery 4
Turn on/off 4
4 Play from Bluetooth devices 5
Connect a device 5
Disconnect a device 5
Reconnect a device 6
5 Play from external devices 7
6 Product information 8
 
Speaker 8
Bluetooth 8
General information 8
7 Troubleshooting 9
General 9
About Bluetooth device 9
8 Notice 10
Care of the environment 10
Trademark notice 11

2EN
1 Important
Warning
 Never remove the casing of this speaker.
 Never lubricate any part of this speaker.
 Never place this speaker on other electrical equipment.
 Keep this speaker away from direct sunlight, naked

Important safety instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or

produce heat.
i Only use attachments/accessories

j 
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
k Battery shall not be exposed to excessive

l Apparatus shall not be exposed to
dripping or splashing.
m Do not place any sources of danger on


Note
 The type plate is located on the bottom of the
apparatus.

3EN
2 Your portable
speaker
Congratulations on your purchase, and

support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can enjoy audio from
Bluetooth-enabled devices or other external
devices.
What's in the box
Check and identify the contents of your
package:
 Speaker
 USB cable for charging
 Short user manual
Overview of the speaker
a LED indicator
abc de
 Indicate battery or Bluetooth
connection status.
b Source selector (OFF/AUDIO IN/ 
 Select Bluetooth or AUDIO IN source.
 Turn the speaker off.
c PAIRING
 Enter Bluetooth pairing mode.
 Disconnect Bluetooth connection.
d DC IN
 Recharge the built-in battery.
e AUDIO IN
 Connect an external audio device.

4EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Charge the built-in battery
The speaker is powered by a built-in
rechargeable battery.
Note
 Before use, fully charge the built-in battery.
 The micro USB socket is for charging only.
 It takes you approximately two hours to fully charge
the battery.
 Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
Connect the USB cable between
 the DC IN socket on the speaker, and
 a USB socket on a computer.
The LED indicator indicates the battery status.
Under charging Fully
charged
"OFF"
mode
Flashing white Off
"AUDIO
IN" mode
Flashing white Solid white
"Bluetooth"
mode
Flashing blue
or solid blue
(depending
on Bluetooth
connection
status)
Flashing
blue or
solid blue
(depending
on
Bluetooth
connection
status)
Turn on/off
 To turn the speaker on, slide the source
selector to AUDIO IN or .
 To turn the speaker off, slide the source
selector to OFF.
Switch to standby mode
The speaker switches to standby mode
automatically in the following situations:
 In Bluetooth mode, the connection with
Bluetooth device is invalid for 15 minutes;
or
 In AUDIO IN mode, no audio input cable
is connected for 15 minutes.

5EN
4 Play from
Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices.
Note
 The speaker can memorize a maximum of four paired

 Any obstacle between this speaker and a Bluetooth
device can reduce the operational range.
 Keep away from any other electronic device that may
cause interference.
 The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
 Make sure that no audio input cable is connected to
the AUDIO IN socket.
Connect a device
1 Slide the source selector to .
» !#$
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (refer to the user
manual of the device).
3 Select [Philips BT50] displayed on your
device for pairing and connection. If
necessary, input “0000” as the pairing
password.
» After successful pairing and connection,
the speaker beeps twice, and the LED
indicator turns solid blue.
 %[Philips BT50] on
your device, press and hold PAIRING
for more than three seconds until you
hear triple beeps.
4 Play audio on the Bluetooth device.
Tip
 You can use your Bluetooth device to control play.

Indicator Bluetooth connection status
Fast
&
(2Hz)
Pairing
Slow
&
(1Hz)
Connecting
Solid blue Connected
Disconnect a device
 Press and hold PAIRING for more than
three seconds;
» The speaker beeps for three times.
 Disable Bluetooth on your device; or
 Move the device beyond the
communication range.
» The speaker beeps twice, and the LED


6EN
Note
 Before connecting another Bluetooth device, disconnect

Reconnect a device
When you turn on the speaker, it will reconnect
the last connected device automatically; If not,
select [Philips BT50] on your Bluetooth device
to start connection.

7EN
5 Play from
external devices
With this speaker, you can also listen to an
external audio device such as an MP3 player.
Note
 Make sure that music playback through Bluetooth is
stopped.
1 Connect an audio input cable (not
supplied) with a 3.5 mm connector on
both ends to
 the AUDIO IN socket on this speaker,
and
 the headphone socket on the external
device.
2 Slide the source selector to AUDIO IN.
» The LED indicator turns white.
3 Play audio on the external device (refer to
its user manual).

8EN
6 Product
information
Note
 Product information is subject to change without prior
notice.

Rated Output Power 1.5W RMS
Frequency Response 100 -16000 Hz,
±3dB
Signal to Noise Ratio > 70 dBA
Audio-in Input 300 mV RMS
Speaker
Speaker Impedance 4 ohm
Speaker Driver 4cm full range
Sensitivity >82dB/m/W±
3dB/m/W
Bluetooth
Bluetooth Version V2.1 + EDR
* A2DP
Bluetooth Frequency Brand 2.4GHz ~
2.48GHz
Bluetooth Range 10 m (Free
space)
General information
Power Supply (through micro
USB socket)
5 V, 0.5 A
Built-in Li-polymer Battery 3.7 V, 365
mAh
Dimensions - Main Unit (W x
H x D)
61 x 76 x
61 mm
Weight - Main Unit 0.1 kg