Philips 14PV182/58 User manual

&
The remote control
RECORD nRecord
STANDBY mStandby
SV/V+ ’SHOWVIEW’ programming
TIMER kTIMER programming on the set
CLEAR bReset/clear
0-9 Digit buttons 0-9
STOP hPause/Stop
GPLAY Playback
DMenu left
CMenu right
Sp Volume control
Amenu Up
Bmenu Down
PpProgramme number Plus/Minus
MUTE yMute sound
MENU Call menu
OK Confirm button
INDEX EIndex search
STILL RStill picture
The following buttons are only available for some
sets:
CLEAR bTELETEXT concealed information
dTELETEXT off (temporarily)
eTELETEXT on/off
fTELETEXT page stop
gTELETEXT enlarged print
Front of the set
mStandby
PpProgramme number Plus/Minus
Sp Volume control
5Record
HRewind/Reverse scanning
hPause/Stop
GPlayback
IForward wind/ Forward scanning
JCassette eject
wHeadphones socket
OPERATING INSTRUCTIONS IN BRIEF

&
Programming with ’SHOWVIEW’
All the information required for programming is encoded in the ’SHOWVIEW’ code.
1Press the SV/V+ button on the remote control.
2Enter the entire ’SHOWVIEW code’. This code (up to 9 digits) is found next to the start time of
a TV programme in your TV guide.
If you entered an incorrect code number, clear it with the CLEAR bbutton.
3If you want to repeat programming at daily or weekly intervals, select the required settings in
the ’DAILY/WEEKLY’ line.
’Daily’ programming can only be used for recordings to be made from Mondays to Fridays
inclusive.
4After confirming the corresponding data appears on the TV screen.
Note: If you use SHOWVIEW for the first time, the ’PROGRAMME NR.’ line appears when you
enter the SHOWVIEW code. Enter the required programme number for this channel.
DATE DW PR START END c
01 01 17:15 18:45
vw 0-9 OK
5Confirm with the OK button.
The data has been stored in a TIMER block.
Please ensure that you loaded a cassette without erase protection.
6Press the STANDBY mbutton.
How to enter, check or clear a TIMER-block manually
1Press the TIMER kbutton.
2Select a free TIMER block or the TIMER block you want to check or clear.
3Clear: Press the CLEAR bbutton.
4Enter/Check: Press the Dor Cbutton to switch between ’DATE’ (date), ’DW’ (daily,
weekly), ’PR’ (programme number), ’START’ (start time) and ’END’ (end time).
Press the Aand the Bor the 0-9 buttons to change the data.
5To end programming, press the MENU button.
6Press the STANDBY mbutton.
Selecting a TV channel
Select the required TV channel (= programme number) with the Ppbutton or the 0-9
buttons on the remote control.
The selected programme number (e.g.: ’P 01’) appears in the upper right corner of the TV screen.
Volume control
You can control the volume level with the Sp button.
If you want to mute the sound temporarily (e.g.: during a telephone call), press the MUTE y
button on the remote control. When you press it again, the sound returns at the same volume level.
Picture control
You can control brightness, contrast, sharpness and colour here.
1Press the MENU button.
2Select and confirm the line ’PICTURE’.
3Select and confirm the TV screen setting.
* In addition, you can adjust the tint for the playback of cassettes in the NTSC standard.

1
Congratulations on the purchase of one of the most sophisti-
cated and simple-to-use television/video recorders combina-
tions (TV combi) on the market. With this TV combi you can
record and play VHS-standard cassettes.
Please take the time to read this operating manual before
using your TV combi.
Safety instructions and other notes
•Danger: high voltage! Do not open the set. The set does not
contain any components that can be repaired by the customer.
When the appliance is connected to the power supply there are
some components that are constantly operational. To switch off
the set completely you must disconnect it from the power
supply.
•Note that this power pack is designed for a power supply of
220-240V/50Hz.
•Ensure that air can circulate freely through the ventilation slots
on the set.
•Ensure that no objects or liquids enter the set. If liquid is spilt
into it, disconnect the set immediately from the power supply
and call the After-sales Service for advice.
•The set should not be used immediately after transportation
from a cold to a hot area or vice versa, or in conditions of
extreme humidity.
After unpacking the set, it should be allowed to acclimatize for
at least three hours before installation.
•These operating instructions have been printed on nonpolluting
paper.
•Deposit old batteries at the relevant collection points.
•Please make use of the facilities available in your country for
disposing of the packaging of the set in a way that helps to
protect the environment.
•This electronic equipment contains many materials that can be
recycled. Please inquire about the possibilities for recycling
your old set.
•SHOWVIEW is a trademark of Gemstar Development Corpora-
tion. The SHOWVIEW system is manufactured under licence
from Gemstar Development Corporation.
Contents Page
1. INSTALLATION 2................................
Connecting additional equipment 2..................
Emergency interrupt 2............................
User guide 2....................................
Making standard settings 3........................
Setting the clock and date 3.......................
2. PLAY BACK 4...................................
Continuous playback 4...........................
3. RECORD 5......................................
Programming with ’SHOWVIEW’ 6..................
4. SPECIAL FEATURES 7............................
On Screen Display (OSD) 7........................
Sleep function (switch off) 7.......................
Switch set on function 7..........................
Child lock 8.....................................
Before you call an engineer 9......................
OPERATING INSTRUCTIONS PHILIPS 14PV182/58

2
Connecting the cables
1Insert the aerial plug into the 2socket.
If you use the auxiliary aerial supplied, push the aerial into
the mounting on the back panel until it snaps into place.
Pull out the telescopic rod(s) as far as required. Tilt and
rotate the aerial until you have got the best picture quality.
2Insert the plug of the mains cable into the wall socket.
3Switch the set on. The power switch mis located on
the left side panel of the set.
Important notes for operation
•We advise you, from now on, to switch the set to standby
using the STANDBY mbutton on the front of the set or
on the remote control.
•When the set is in the standby mode, a small red lamp on
the left of the front of the set will be alight.
•You can switch on with the STOP hbutton, the
0-9 buttons or by inserting a cassette.
•Attention: When you use the power switch mon the
side panel, you have completely switched off the set from
the mains power supply. No programmed recordings will
then be made. The red lamp on the left of the front of the
set will not be alight. After a few hours, the date and
clock settings will be lost.
•Attention: Before you switch off the appliance with the
power switch m, remove the tape by pressing the
Jbutton.
•Keep your TV Combi connected to the mains and the
power switch in ’on’ position at all times to ensure that
programmed recordings can be made and that the
television functions normally. The power consumption
required is low.
•Back-up power supply: TV channel storage - typically 1
year, Clock/Timer - typically 7 hours.
Connecting additional equipment
You can also connect additional equipment to the
EXTERNAL socket, for instance, a decoder satellite receiver
or camcorder.
Emergency interrupt
Both the set and the remote control have an ’Emergency
interrupt’ button. You can use the STANDBY mbutton to in-
terrupt any function.
Whenever you have operating problems you can simply
interrupt the function and start again.
You can practise operating your set without any worries. No
matter which buttons you press, you cannot damage it.
User guide
With OSD (On Screen Display) the corresponding functions
appear on the TV-screen. The most important button-func-
tions are displayed at the bottom of the screen.
Throughout this instruction manual, use the following buttons
for the functions ’Call up’, ’Select’, ’Enter’/’Adjust’, ’Confirm’
and ’Exit’:
•Call up: Use the MENU button.
•Select: Select a line with the Aor Bbutton. Use
the 0-9 buttons or the Dor Cmenue button
to select within a line.
•Enter/Alter: With the Dor Cor with the 0-9
button.
•Confirm: With the OK button.
•Exit: With the MENU .
1. INSTALLATION

3
Making standard settings
1To start, press the STOP hbutton. Press the D
button and the Cbutton simultaneously.
INSTALLATION vw
LANGUAGE EN
COUNTRY UK
AUTO STORE
MANUAL STORE
SORT
PP STORE
2Select the required display language in the ’LANGUAGE’
line.
3Select your country in the ’COUNTRY’ line.
Setting the clock and date
1To start, press the STOP hbutton.
2Press the MENU button.
3Select and confirm the line ’FEATURES’.
4Select and confirm the line ’SET CLOCK’.
SET CLOCK
TIME 20:00
YEAR 1998
MONTH 01
DATE 01
xy 0-9
5Enter the time, year, month and date.
Automatic Channel Search
1Switch on with the STOP hbutton. Press the D
button and the Cbutton simultaniously.
2Select and confirm the line ’AUTO STORE’.
The ’Automatic Channel Search’ function starts.
AUTO STORE
PRESS xyTO STOP
SEARCH
PLEASE WAIT
CHANNELS FOUND: 1
aaabbbbbbbbbbbbbbbbb
3Wait until all TV channels have been stored.
All TV channels will be stored from programme number
69 downward.
How you can search for a TV channel manually, you can read
in chapter 4 ’SPECIAL FEATURES’ in the section ’Manual
channel search’.
Note:
* If the ’Automatic channel search’ function is activated,
any previously programmed TIMER blocks will be
cleared.
You can store up to 69 TV channels.
Allocating channel numbers
1Switch on with the STOP hbutton. Press the D
button and the Cbutton simultaneously.
2Select and confirm the line ’SORT’.
SORT vw
C-21
FROM P01
TO P02
STORE
3On the TV screen, in the line ’FROM’, select the TV
channel to which you want to allocate a programme
number, e.g.: ’P 01’.
4In the line ’TO’, select the required programme number,
e.g.: ’P 02’.
5Select and confirm the line ’STORE’.
The allocated TV channels will be exchanged.
6Repeat steps 3to 5until you have allocated a pro-
gramme number to all the required TV channels.
To finish, press the MENU button twice.

4
1Insert a cassette into the cassette slot.
2Press the GPLAY play back button.
3Picture search: Now press the H(rewind) or I
(wind) button once or several times.
4Interrupt: Press the STOP hbutton.
5Wind: Stop the tape and press the H(rewind) or the
I(wind) button.
6Eject: Press the Jbutton on the set.
Note: Some functions switch off automatically after a
while (e.g.: Pause, Still Picture, Scanning). This helps to
protect the cassette and prevent unnecessary power
consumption.
* With this set you can play back cassettes that have
been recorded on another TV combi in the NTSC
standard.
* If you load a cassette with erase protection, the TV
combi starts the play back automatically.
* The picture quality is affected during scanning. The
sound is switched off.
* Remove the cassette before transporting the TV
Combi.
Still picture
1Press the STILL Rbutton. You see a still picture.
Interference stripes will appear.
Each time you press the STILL Rbutton again the pic-
ture will move on one step.
Continuous playback
1Press the MENU button.
2Select and confirm the ’SPECIAL’ line.
3Select the ’REPEAT PLAY’ line. Switch on the continuous
playback.
4Press the MENU button.
5Start the continuous playback with the GPLAY playback
button.
6If you want to cancel the function, stop the continous
playback in the ’REPEAT PLAY’ line.
Tape position/Index search
Tape position: If you press the OK button the tape position
will be shown in the display during Wind, Rewind, Record,
Play back and Pause/Stop.
Index search: Every time you start to record, the tape is
marked with a code mark.
1Press the INDEX Ebutton. Press the Ibutton to
select the next code mark or the Hbutton for the
previous code mark.
2Once the TV Combi finds the code mark or unrecorded
area it will automatically switch to play back.
Note: When you press any tape transport button (e.g.:
the Hor Ibutton) this search function will be
stopped.
* You cannot use this function with recordings made on
another video recorder that does not have this function.
Eliminating picture interference
1During playback press the MENU button.
2Select and confirm the ’SPECIAL’ line.
3Select the ’TRACKING’ line.
4Press the Dor Cbutton until the playback
quality is at its best.
5Press the MENU button. This setting will remain until
you remove the cassette.
6Cleaning function: Press the MENU button.
7Select and confirm the ’SPECIAL’ line.
8Select the ’CLEANING’ line.
9Press the OK button. A blue screen appears for a few
seconds.
0Wait until the blue screen disappears and press the
MENU button.
Note:
* Some hired cassettes may have a poor picture/sound
quality. This is not a fault in your set.
2. PLAY BACK

5
1Insert a cassette.
2Use the Ppbutton to select the programme number
from which you wish to record, e.g.: ’P 01’.
3Press the RECORD nbutton.
4Use the STOP hbutton to stop the recording.
5If, whilst recording, you want to switch off the TV screen,
press the STANDBY mbutton once.
To switch the TV screen on again, press the Pp
button.
Important notes for recoding
•OTR: If you do not want to record to the end of the
cassette, press the RECORD nbutton again. The display
shows at what time the recording will stop.
With the Dor the Cbutton you can change the
end time of the recording in 30 minute intervals.
If you wish to cancel the end time, press the CLEAR b
button.The recording goes on uninterruptedly. (This does
not effect the recording.)
•Programme number ’E1’ is provided for recording from
external sources (via the EXTERNAL scart socket).
•Erase protection: So that you don’t accidentally delete an
important recording, you can remove the special tab
(erase protection) on the narrow side of the cassette with
a screwdriver or slide the special tab to the left.
Later, if you no longer want the cassette to be erase
protected, you can seal the gap again with adhesive tape
or slide the special tab to the right.
•Auto-assembling: You can use the auto-assembling func-
tion to join individual recordings without any major
picture disturbance between the recordings.
Search for the correct position on the tape and then stop
the playback by pressing the STOP hbutton. ’PAUSE’
appears in the display.
Now start recording as usual by pressing the
RECORD nbutton.
Programme a recording
The set needs the following information for every pro-
grammed recording:
* the date on which the recording is to be made
* the programme number for the TV channel
* the start and end time of the recording
* VPS on or off
The set stores all the information mentioned above in what is
known as a TIMER block. It can store 6 TIMER blocks for up
to one month in advance.
’VPS’ (Video Programming System)
With VPS, the TV station controls the start and the duration
of a programmed recording. This means that the video
recorder switches itself on and off at the right time even if a
TV programme you have programmed begins earlier or
finishes later than expected.
Usually the start time is the same as the VPS time. If,
however, a different VPS time code is given, e.g.: ’20.15 (VPS
20.14)’, you have to enter ’20.14’ (the VPS time) exactly to the
minute.
If you are not using VPS, the ’VPS’ indication must be off.
3. RECORD

6
Programming with ’SHOWVIEW’
All the information required for programming is encoded in
the ’SHOWVIEW’ code.
1Press the SV/V+ button on the remote control.
2Enter the entire ’SHOWVIEW code’. This code (up to 9
digits) is found next to the start time of a TV programme
in your TV guide.
If you entered an incorrect code number, clear it with the
CLEAR bbutton.
SHOWVIEW
CODE 53124----
DAILY/WEEKLY ONCE
PROGRAMME NR. 01
xy 0-9 OK
3If you want to repeat programming at daily or weekly
intervals, select the required setting in the
’DAILY/WEEKLY’ line.
’Daily’ programming can only be used for recordings to
be made from Mondays to Fridays inclusive.
4After the confirmation the corresponding data appear on
the TV screen.
Note: If you use SHOWVIEW for the first time, the
’PROGRAMME NR.’ line appears when you enter the
SHOWVIEW code. Enter the required programme num-
ber for this TV channel.
DATE DW PR START END c
01 01 17:15 18:45
vw 0-9 OK
5Confirm with the OK button.
The data has been stored in a TIMER block.
Please ensure that you loaded a cassette without erase
protection.
6Press the STANDBY mbutton.
How to enter, check or clear a TIMER
block manually
1Press the TIMER kbutton.
2Select a free TIMER block or the TIMER block you want
to check or clear.
3Clear: Press the CLEAR bbutton.
4Enter/Check: Press the Dor Cbutton to switch
between ’DATE’ (date), ’DW’ (daily, weekly), ’PR’ (pro-
gramme number), ’START’ (start time) and ’END’ (end
time).
Press the Aand the B, or the 0-9 buttons to
change the data.
5To end programming, press the MENU button.
6Press the STANDBY mbutton.
Important notes for programmed recordings
•If the message ’PLEASE PRESS STOP’ or ’PLEASE PRESS
STANDBY’ appears on the TV screen, press the
STOP hor the STANDBY mbutton.
A TIMER recording will function only, if the set isn’t used
for other video recorder functions (e.g.: playback).
•The TIMER lamp on the front of the set lights up when
one or more of the TIMER blocks are occupied.
•If the end of the cassette is reached during a recording,
the video recorder automatically ejects the cassette. The
set switches off after a few minutes.
•If you forget to load a cassette, ’NO CASSETTE CANNOT
RECORD’ will appear.
•If you inserted a cassette with erase protection when you
want to start a recording, the cassette will be ejected.
•If ’CODE ERROR’ appears on the TV screen, you entered
an incorrect code number or the incorrect date. Repeat
the entry or end with the STANDBY mbutton.
With ’Daily’ programming, the first recording must take
place within a week.
•If ’DAILY ERROR’ appears on the TV screen, the date was
incorrectly entered. ’Daily’ programming can only be used
for recordings to be made from Mondays to Fridays
inclusive.

7
On Screen Display (OSD)
You can switch OSD on or off.
1Press the MENU button.
2Select and confirm the ’FEATURES’ line.
FEATURES vw
PP RECALL
ON TIMER
SLEEPTIMER 0
DISPLAY FULL
CHILD LOCK OFF
SET CLOCK
3Select the ’DISPLAY’ line.
4Select one of the options indicated.
’FULL’: OSD appears for a few seconds each time an
operating mode is selected and then disappears.
’OFF’: OSD is switched off.
’PROG’: only the programm number appears.
’COUNT’: only the counter appears.
5Confirm it with the MENU button.
Note: With the OK button you can superimpose the
actual operating mode on the TV screen.
Personal Preset
You can make your personal picture and volume settings
here. You can call up this setting and it will be used
automatically when you switch the set on.
1select your personal setting. (see chapter ’The TV set
functions’). Press the Dbutton and the Cbutton
simultaniously.
2Select and confirm the ’PP STORE’ line.
3To end press the MENU button. The personal setting
has been stored.
4Calling up your Preset: Press the MENU button.
5Select and confirm the ’FEATURES’ line.
6Select and confirm the ’PP RECALL’ line.
7Press the MENU button. The set will use this setting.
Sleep function (switch off)
You can programme your set to switch off after a predeter-
mined period.
1Press the MENU button.
2Select and confirm the ’FEATURES’ line.
3Select ’SLEEPTIMER’ line.
4With the Dor the Cbutton you can determine
the minutes left until switch off in 15 minutes intervals.
When you set the time to ’0’ with the CLEAR bbutton
the sleep function is switched off.
5Press the MENU button.
Switch set on function
You can programme your set to switch on at a predetermined
time.
1Press the MENU button.
2Select and confirm the ’FEATURES’ line.
3Select and confirm the ’ON TIMER’ line.
4Determine the time you wish the set to switch on.
5Select the ’WAKE UP’ line and switch the ’on-timer’ on or
off.
6Press the MENU button.
4. SPECIAL FEATURES

8
Child lock
1Press the MENU button.
2Select and confirm the ’FEATURES’ line.
3Select the ’CHILD LOCK’ line.
4Switch the child lock on or off.
5Press the MENU button.
Note: If a button is pressed with the childlock ’on’,
’CHILD LOCK’ appears for a few seconds in the display.
* Programmed recordings are made despite the child
lock and cannot be interrupted.
Manual channel search
In certain cases the Automatic Channel Search may not be
able to find all of the TV channels (e.g.: coded TV channels).
You can then use this manual method to set the channels.
1Switch on the set with the STOP hbutton. Press the
Dbutton and the Cbutton simultaniously.
2Select and confirm the ’MANUAL STORE’ line.
MANUAL STORE vw
CHANNEL/FREQ.
SYSTEM EUR
SEARCH C-21
FINE TUNING
PROGRAMME NR. 1
DECODER
STORE
3Select the ’SEARCH’ line.
4Press the Cbutton as often as necessary, until you
have found the right TV channel.
Note:
* If you want to allocate a decoder, switch the decoder
function on or off with the Dor Cbutton in the
’DECODER’ line.
* If you want to change the automatic channel setting,
select the ’FINE TUNING’ line.
With the Dor Cbutton you can vary the auto-
matic TV channel setting.
Important: This re-tuning is only necessary and useful in
special cases, e.g.: when there are stripes on the
picture with cable-TV systems.
5In the ’PROGRAMME NR.’ line use the Ppbutton to
select the required programme number, e.g.: ’P 01’.
6Select and confirm the ’STORE’ line.
7If you want to search for further TV channels, start again
at step 4.
To finish, press the MENU button twice.

9
Before you call an engineer
If, contrary to expectation, you experience any difficulty in
operating this TV Combi, please call the customer service in
your country.
You will find the telephone numbers in the enclosed guar-
antee leaflet.
The set does not respond to any button being pressed:
•No power supply.
•Technical disturbance: disconnect from the mains for 30
seconds, then re-connect.
•The power switch on the side panel is switched off.
•Child lock is active.
Cassette jammed:
•Don’t use force. Pull out the mains plug for a moment.
Remote control does not operate:
•Remote control wasn’t pointed at the set.
•Batteries are exhausted.
No playback on TV Combi:
•No recording on the cassette.
No TV reception:
•The aerial is not connected.
•No TV channels have been stored.
Poor playback from TV combi:
•Cassette badly worn or of poor quality.
•Use the ’TRACKING’ function.
No recording possible:
•TV channel not stored or wrongly selected.
•Cassette with erase protection has been loaded.
Programmed recording does not function:
•TIMER not set properly.
•Time data wrongly programmed.
•A cassette with erase protection has been loaded.
•VPS switched on but ’VPS time’ wrong. Check aerial.
This product complies with the requirements of the Directive
73/23/EEC + 89/336/EEC + 93/68/EEC.
TYPE 14PV182/58
VNxx SER.NR......

10

11

12
3103 166 20311
8135/003 (WwnnNNNwwnwNNnwnWwnNNNwwnWnnnW) 14PV182/58