Photoflex LP-SWVLHRDWR User manual

For detailed specifications, product tutorial videos and more, please visit www.photoflex.com
LitePanel Mounng Hardware Instrucons • Item: 870571 (LP-SWVLHRDWR)
LitePanel Mounng Hardware
The LitePanel Swivel Mount Hardware is designed to interface the
LitePanel line of frames with the LiteReach® Plus handheld extension
or the appropriate Photoex LiteStand.
Before assembly check to make sure you have all of the following parts
• 1ea. Swivel Stand Mount
• 1ea. Upper Cover
• 1ea. Lower track mount
• 2ea. 6mm / .75 x 10mm Socket head screws
• 1ea. 3/16”/5mm allen wrench
Aaching the LitePanel Mounng Hardware to LitePanel Frames:
Note: You should have the assembled LitePanel frame lying on a at
surface
Step 1 Disassemble the upper cover from the lower track mount
using the allen wrench. Figure 1
Note: There are two mounng opons for the LitePanel Mounng
Hardware depending on your applicaon:
A. If you are using the hardware with the LiteReach Plus extension
pole then you will only use one LitePanel hardware set. The
orientaon of the lower track plate will have the swivel track in a 90
degree posion in relaon to the frame tube. Figure 2
B. If you are using the LitePanel hardware with two light stands to
mount the LitePanel overhead, two LitePanel hardware sets will be
required. The orientaon of the lower track plate will have the swivel
track in a parallel posion in relaon to the frame tube. Figure 3
Note: For most applicaons it is recommended that you aach the
hardware in the middle of the width of the frame for the best balance
and stability.
Step 2 Place the track plate under the frame tube, making sure the
swivel track is in the desired posion. Figure 4
Step 3 Place the Top Cover over the frame tube aligning the holes
with the lower Track plate for the aachment screws. Figure 5
Step 4 Aach the top cover to the lower track plate by securely
ghtening both socket screws using the Allen wrench. Figure 6
Figure 2.
Swivel Stand
Mount
Upper Cover
Lower Track Mount
Socket Head Screws
Allen Wrench
Figure 1.
Figure 3.
Figure 5. Figure 6.
Figure 4.
Rev 09/2016

For detailed specifications, product tutorial videos and more, please visit www.photoflex.com
Figure 9.
Figure 10. 39” x 39” LitePanel/
LiteReach Kit
Figure 7. Figure 8.
Alternavely, the hardware can be aached so that the track plate is
facing out from the edge of the frame. In this conguraon, a second
fabric can be aached on the opposite side for a quick change of
reector surfaces or for double diusion. Figure 7
Step 5 With either one or two upper and lower components aached
to the frame. Slide the swivel stand mount onto the swivel track on the
lower plate and ghten the set screw knob. Figures 8-9
Tip: When using the LitePanels extended like a boom as shown in gure
10, put the swivel handle on your le side when aaching it to the
mounng track. In this way, gravity works with you allowing the weight
of the LitePanel to further ghten the swivel rather than loosen it.
With the Hardware securely aached, it is now ready to be placed on a
Photoex LiteStand or the LiteReach Plus hand held extension. Figures 10-12
Figure 11. 77” x 77” LitePanel Kit
Figure 12. 39” x 39” PVC LitePanel Kit
Customer Support [phone]
E-mail: [email protected]
Photoflex is a division of PromarkBRANDS, Bartlett, IL USA.
©2016 ALL RIGHTS RESERVED. LiteReach®, Photoflex® and the Photoflex logo are
trademarks or registered trademarks of Photoflex and/or its affiliates in the U.S.
and other countries.
PHOTOFLEX® WARRANTY
• Warranties only cover manufacturer’s defects and workmanship.
• We reserve the right to inspect all merchandise returned (end
users and dealers) for warranty fulfillment.
• All returns must be pre-approved with Return Manufacturers
Authorization obtained from Photoflex/PromarkBRANDS.
• A receipt showing date of purchase will be required for all returns.
• Freight must be paid by the customer or dealer.
• Warranties are valid only from date of Original Purchase.