Ergo Tab EBLTK4 User manual
Thank you for choosing this product! We strive to provide you with the
best quality products and services in the industry. Should you have any
Model: EBLTK4
V1.0
TV WAll Mount Instruction Manual
Weight Restrictions
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
within the maximum weights indicated. Use with
products heavier than the maximum weights
indicated may result in failure of the mount and
its accessories, causing possible
damage and or injury.
WARNING
If your TV weighs more, this
mount is NOT compatible.
132 lbs.
(60.0 kg)
V1.0
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete
block and brick walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Check the VESA Pattern of TV before the Installation
If your TV VESA is greater than 600x400 mm/24x16in. or less than
VESA 100x100mm/4x4 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX: 600mm/24 in.
MAX: 400mm/16 in.
Minimum VESA pattern:
100mm/4 in.(W)x100mm/4 in.(H)
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
100 mm ≈ 4 in.
300 mm ≈ 11 3/4 in.
600 mm ≈ 23 6/10 in.
01 02 03 04 05 06 07 08 09 10
Tools Needed (Not lncluded)
Supplied Parts
Wall Plate 01 x1 Wall Plate Extender 02 x1
x1
05Level
Bracket x1
03
Bracket x1
04
5/16 in.(8 mm)
Wrench
5/32 in.(4 mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
3/8in.(10mm)
Socket Wrench
Phillips
Screwdriver
Awl
Stud Finder Tape Measure Pencil Drill Hammer
01 02 03 04 05 06 07 08 09 10
Lag Screw
ST7X55mm
x4
A
x8
10mm
x8
5mm
Supplied Hardware
Hardware for Attaching TV Brackets to TV
TV Bolt
Hardware for Attaching Wall Plate to Wall
08
06
[M-H]
[M-A]
[M-D]
[M-E] [M-F] [M-G]
[M-J] [M-I]
07
x4
M4/M6
M8
M6
M4 M4 x 12mm x4 M4 x 30mm x4
M6 x 15mm x4 M6 x 30mm x4
M8 x 15mm x4 M8 x 45mm x4 M8 x 65mm x4
Washer
[If necessary]
Spacer
[If necessary]
[M-C]
[M-B]
This anchor is for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
Anchor
φ10
x4
B
01 02 03 04 05 06 07 08 09 10
Step 1 Select TV Bolts
Step 2 Select Spacers (if needed)
Only one bolt size fits your TV.
M6M4 M8
Too Short Too Long
3
For Rounded TV
For Flat TV with:
Inset Holes Cable Interference
aLong Bolt
Short Bolt
Washer
Washer
Spacer
TV Bracket
TV Bracket
EXTRA
08
08
06
07
06
NO SPACER bSPACER
For Flat TV
Spacer not necessary
SPACE
[for M4/M6 bolt]
[for M4/M6 bolt]
Note: If necessary, the spacers can be used in multi-layer. If the installation
fails after trying various methods, please contact customer service at
01 02 03 04 05 06 07 08 09 10
Alternate Spacer
Setups
Step 3 Secure the TV Brackets to Your TV
Step 4 Assemble Wall Plate(optional)
With Spacer
b
08 No Spacer
a
08 08
06
06
07
04 03
16 in. (406mm) stud spacing
and
VESA Pattern of TV:
100X100-400X400mm
18-24 in. (457mm-610mm)
stud spacing
or
VESA Pattern of TV:
100X100-600X400mm
DO NOT overtighten.
Tighten only until snug.
Z Y X
02
01
01
Option A:
Option B:
Z Y X
02
01 02 03 04 05 06 07 08 09 10
01
Step 5
For wood stud installation, follow STEP 5A
For concrete installation, follow STEP 5B
Attach the Wall Plate [01] or [01 and 02] to Wall
Step 5A Wood Stud Option
X
5A-2
5A-1
01
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in.
(38 x 89 mm)
● Stud center must be verified
● Ensure the wall plate [01] or [01 and 02] is securely fastened to the wall
before continuing on to the next step.
● DONOT USE ANCHOR [B] FOR THIS STEP!
● Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A]. Tighten the lag screws [A] only until they are pulled firmly against the wall
plate.
WARNING:
Position the wall plate [01] or
[01 and 02] at your desired
height and line up the holes with
your stud center line. Level the
wall plate and mark the holes.
16 in.
(406mm)
24 in.
(609mm)
Use a stud finder(not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
Awl
(Not lncluded)
01 02 03 04 05 06 07 08 09 10
Anchor
B
Step
5B
Solid Concrete or Concrete Block Option
5A-4
A
3/8 in.(10 mm)
Socket Wrench
(Not included)
5A-3
5/32 in.(ø4 mm)
2 in.(55 mm)
● Avoid potential personal injury or property damage! DO NOT over-tighten the lag
screws [A]. Tighten the lag screws [A] only until they are pulled firmly against the
wall plate [01] or [01 and 02].
● Ensure the wall plate [01] or [01 and 02] is securely fastened to the
wall before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate [01] or [01 and 02] directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks.
WARNING:
Install the wall plate [01] or [01
and 02] using lag screws [A].
Tighten the lag screws [A] only
until they are pulled firmly
against the wall plate.
Drill 4 pilot holes using a
5/32 in.(4 mm) diameter drill
bit. Make sure the depth is
not less than 2 in.(55 mm).
01
01 02 03 04 05 06 07 08 09 10
3/8 in.(10 mm)
Socket Wrench
(Not included)
5B-3
B
01
5B-1
5B-2
3/8 in.(ø10 mm)
2.4 in.(60 mm)
01
A
Use the hammer to knock
anchors [B] into the wall.
Be sure the anchors [B]
are seated flush with the
concrete surface.
Install the wall plate [01] or [01 and 02] using lag
screws [A] and anchors [B]. Tighten the lag screws
[A] only until they are pulled firmly against the wall
plate. DO NOT over-tighten the lag screws [A].
Drill 4 pilot holes using a 3/8 in.(10 mm)
diameter drill bit. Make sure the depth is
not less than 2.4 in.(60 mm). Never drill
into the mortar between blocks.
Position the wall plate [01] or [01
and 02] at your desired height, level
the wall plate and mark the pilot hole
locations.
01 02 03 04 05 06 07 08 09 10
Step 7 Hang TV to the Wall Plate [01] or [01 and 02].
HEAVY! You may need assistance with this step.
5/16 in.(8mm)
Wrench
03
04
Top of TV
Bottom of TV
S
Loosen
Tighten
S
Loosen the 4 tilt bolts [S] on both brackets, adjust the hooks of the bracket to
the desired angle, then tighten tilt tension nuts using a wrench (not included)
and the titlt bolts using a phillips screwdriver (not included) to fix the tilting
angle of TV.
Step
6
Adjust the Tilt Angle of TV
01
02
01 02 03 04 05 06 07 08 09 10
Locking
03
04
Step 8
Secure TV
Pull down and hold both cords [R], press the bottom of the TV into the wall plate
[01] or [01 and 02] until the latches lock the TV in place.
Press
R
Disconnect all cables, pull down and hold both cords [R] while gently pulling the bottom of
the TV away from the wall.
CAUTION: Avoid potential personal injury or property damage! To prevent the latches from
breaking, always pull and hold the cords [R] down while pulling the TV away from the wall.
Then lift the TV up and remove from wall plate [01] or [01 and 02]. Place the TV on cardbard
or other protective surface to avoid damage.
NOTE: To rehang the TV, follow the procedures in Step 7 and 8.
HEAVY! You may need
assistance with this step.
Unlocking
R
Step 9
Remove the TV
01 02 03 04 05 06 07 08 09 10
All of us do appreciate your product purchase. We hope that you are as happy with
your product as we designing and manufacturing it for you. We strive to provide
you with the best quality products and services in the industry. If you have any
Thank you again for
choosing this product!
Table of contents
Other Ergo Tab Rack & Stand manuals
