Pincheng PC-P03 Parts list manual

1
Pellet Stove
PC-P03
INSTRUCTIONS FOR INSTALLATION, USEAND
MAINTENANCE
The
instruction
manual is an integral
part
of the product.
English

2018PC-P03/03
2
Dear Customer,
Thank you for having chosen one of our products, which is the result of years of experience and continuous research aimed at making a superior
product in terms of safety, reliability and performance.
This booklet contains information and advice for safe and efficient use of your product.
IMPORTANTINFORMATION
The following symbols are used in some parts of the booklet:
CAUTION: for actions that require particular caution and
suitablepreparation.
FORBIDDEN: for actions that UNDER NO CIRCUMSTANCES
must be carried out.
Contact local building authority (such as municipal building
department, fire department, fire prevention, bureau. etc.)
before installation to determine if a permit and/or inspection
is required.
• This instruction booklet has been prepared by the manufacturer and is
an integral part of the product. In the event of sale or relocation of the
product make sure this booklet accompanies it, since the information
contained in it is intended for the purchaser and for anyone involved
in the installation, use and maintenance of the product.
•
Read the instructions and the technical information contained in
this booklet carefully before proceeding with installation, use or any
repairs.
• The observance of the instructions and technical information in this
instruction booklet guarantees the safety of persons and property; it
also ensures more efficient operation and an increased lifespan.
• Manufacturer or distributor cannot be held responsible for
damage or injury due to failure to comply with the instructions for
installation, use and maintenance given in this booklet, or due to
unauthorized alterations or to the use of other than original spare
parts.
• Appliance installation and use must conform with the manufacturer’s
instructions as well as with European and national legislation and
local regulations.
•
Installation, electrical connection, checks, maintenance and repairs
are operations which must be carried out exclusively by qualified and
authorized personal with specialize knowledge of the product.
• The wall against which the product is to be placed must not be of
wood or any other flammable material. For correct installation it is
also important to comply with the section entitled “MINIMUM SAFETY
DISTANCES ”.
• Before installing the product read all instruction booklets relevant to
the cladding, the ventilation kit and any other accessory.
• Check that the floor where the product is to be installed is perfectly
level.
• When handling the steel parts of the cladding it is advisable to use
clean cotton gloves to avoid leaving fingerprints that are difficult to
remove atfirsttime ofcleaning.
•
The stove must be assembled by at least two persons.
• Connectthepelletstovetotheelectricitysupplyonlyafterithasbeen
connected by an expert to the flueway.
• Theplugattheendofthepowercablemustbeeasilyaccessibleafter
installation.
• Use only recommended wood pellets in the pellet stove (refer to
section entitled“FUEL”).
•
Neveruse liquidfuelstolightthepelletstoveortorelighttheembers.
• Ensure that the area where the stove is installed is properly ventilated
while the stove is lit.
•
Intheeventofmalfunctioningthefuelsupplywillbestopped.Restart
the stove only after having eliminated the cause of the malfunction.
• Stopusingthe productintheeventoffaultormalfunctioning.
• Donotremovetheprotectivegrillefromthepellethopper.
• Any build-up of unused pellets in the burner left over from repeated
failed ignitions must be removed before attempting to light the stove
again.
•
Stove operation can result in surfaces, handles, flue pipe and glass
becoming extremely hot. When the stove is in operation, only touch
these parts if wearing protective clothing otherwise use suitable tools.
• Becauseofthebuild-upofheatontheglass,takecarethatthosewho
areunfamiliarwithstoveoperationdonotlingernearthestove.
• This appliance must not be used by persons (including children) with
reduced physical, sensory or mental capacities, or lack of experience
or knowledge unless they are supervised or instructed on use of the
appliance by the person who is responsible for its safety.
•
Creaking may be heard while the stove is in operation or cooling
down. This is not to be considered a defect, but is a consequence of
thermal expansion of the component materials.
• The product you have purchased may different slightly from the one
illustrated in this booklet since the pictures are only given as an
indication and not an exact portrayal.
In the event of difficulties or if you are unable to understand
the instruction booklet, contact your local dealer.
Do not place objects which are not heat-resistant on top of
the stove or within the recommended minimum safety area.
Do not open the door while the stove is in operation or operate
the stove when the glass is broken.
In case of any alarm signals do not unplug the stove: just turn
the unitOFF.
See the guarantee certificate enclosed with the product for the terms, limitations and exclusions.
In line with its policy of constant product improvement and renewal, the manufacturer may make changes without notice.

2018PC-03/03
3
CONTENTS
Section Title Page
GENERAL RULES 4
Soot inspection 4
Fresh air intake 5
Outside combustion air 5
Installation environment 5
Capacity load of the floor 6
Minimum safety distances 6
Flueway 7
Interior vent installation 9
Connecting to a conventional chimney 10
Installing into an existing firebox chimney 11
Short rise installation –Wall outlet 11
Venting: termination requirements 12
Prevention of domestic fires 13
Mobile home installation 14
TECHNICAL CHARACTERISTICS AND SPECIFICATIONS 15
Features 15
Technical data 15
Accessories and equipment 15
Product identification data 16
Dimensional diagram 16
Wiring diagram 17
3.0 FUEL 18
4.0 PREPARING FOR INSTALLATION 18
USE 19
Loading the pellets 19
6 .0 PRODUCT AND CONTROL SYSTEM 20
Product overview 20
Control system - Main page 21
Control system - Setting page 22
Control system - Timing program 23
Control system - Factory model 24
7 .0 ERROR AND SOLUTIONS 25
8. 0 MAINTENANCE 26
5.0
English
2.0
1.0

2018PC-P03/03
4
1.0 GENERAL RULES
Ensure that the installation of your product conforms to all the indications given below.
Fig. 1
CHIMNEY STACK
CHIMNEY
CONNECTION
TO FLUE
FLUEWAY
SOOT INSPECTION APERTURE
FRESH AIR INTAKE
ELECTRIC
POWER SUPPLY
CAPACITY LOAD OF
THE FLOOR
MINIMUM SAFETY
DISTANCES
SOOT INSPECTION
We recommend that the flue must have a chamber for collecting solid matter and any condensate located below the connection
and which may be easily inspected by means of an airtight door. (Fig. 1)
English

2018PC-03/03
5
FRESH AIR INTAKE
To ensure trouble-free operation the stove must have the
necessary air available for combustion and this is provided
through the fresh air intake.
The fresh air intake must:
- have a total free cross section at least equal to the size
given in the paragraph “ TECHNICAL DATA ”;
- be protected by a grille or suitable guard provided it does
not reduce the minimum recommended section;
- be in a position whereby it cannot be obstructed.
Fig.
2
OUTSIDE COMBUSTION AIR
It is recommended that the stove be connected to an outside
source of combustion air under certain conditions (negative
pressure).
To install outside air use any 2” I.D. flexible metal hose or
rigid metal pipe (conduit).
It must be connected around (NOT INSIDE) the combustion air
inlet tube (Fig. 3).
Increase the outside air pipe diameter to 3” for runs over 15 ft
(4.5 m) and elevation over 4 ft (1 m).
Long runs should be avoided.
Fig.
3
Be careful not to pinch or bend the outside air pipe with
too small a radius.
Outside Air Pipe may be terminated flush with the outside
wall but should be protected from wind and weather by a
hood.
The outside air pipe must terminate above the
maximum snow line and below the exhaust vent outlet.
Take care not to draw cold air past water pipes that may
freeze.
An open mesh screen should be placed over the outside air pipe
opening to prevent birds or rodents from nesting in the opening.
Use an elbow or shield to prevent prevailing winds from blowing
directly into the outside air intake pipe.
NOTE: Mesh screen should be no smaller than 1/4” by 1/4”
(6.4 by 6.4 mm).
Outside combustion air is required for all mobile
home installations and where building codes require.
In bedroom or bathroom installations the outside
air connection is required.
Contact local building authority before installation to determine if a permit and/or inspection is required.
When locating your appliance, consider the building structure to ensure the vent will not interfere with any ceiling joists, roof rafters,
wall studs, water pipes or electrical wiring. It may be easier to relocate the appliance than to rework the building structure.
The room where the appliance is to be installed must comply with the following requirements:
They must not be used as a garage, store for combustible material or for activities with a risk of fire.
Locating the stove in a room with an explosive atmosphere is prohibited.
They must not be in a vacuum in relation to the outside environment due to the effect of contrary draught caused by the
presence in the room where the firebox is installed of another appliance or an extractor device.
The stove or firebox must not be used simultaneously with collective type ventilation ducts with or without extractor fan,
other devices or other appliances such as: forced ventilation systems or other heating systems using ventilation to change the
air. Such systems could cause a vacuum in the environment of installation even if installed in adjoining or communicating
rooms.

2018PC-P03/03
6
Fig. 7
SEE VENT
MANUFACTURER'S
INSTRUCTIONS
Check the load-bearing capacity of the floor, referring to the weight of the product given in the paragraph “TECHNICAL DATA”. If
the floor does not have a suitable load-bearing capacity, adequate countermeasures must be taken.
MINIMUM SAFETY DISTANCES
Install the product in compliance with the recommended safety distances
from heat sensitive or inflammable materials and not inflammable, from
load bearing and other walls and also from wooden elements, furniture,
etc.
The minimum distances are:
- 4” (10 cm) from the wall behind the stove;
- 6” (15 cm) from the side wall;
- 32” (80 cm) in the heat radiation area and from the the hot air fan
outlet.
In the case of flooring that is heat sensitive or inflammable the floor
must be protected with non-combustible insulating material, e.g. sheets
ofsteelplate,marble,tiles,etc.
The floor protection must extend:
- under the product;
- a minimum of 6” (152 mm) in front of unit and beyond each side of
the fuel loading and ash removal opening (4” / 10cm from the external
side of the coating).
Connection to the flue must respect minimum safety distances from
heat-sensitive structural components or inflammable materials (wood
paneling, beams or ceilings, etc) shown in figures.
The stove will become hot while in operation. Keep children
away from all stovesurfaces.
Direct contact with stove while operating may cause skin
burns.
Keep any combustible product such as wooden furniture,
curtains, carpets, combustible liquids, etc. well away from the
stove when it is lit (minimum distance 32” / 80 cm).
It is recommended that greater distances than those indicated
above be left all round the stove to make any necessary work
on the appliance easier.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
Certain local code restrictions may apply.
Check with Local Officials first before installing.
Fig. 4
REAR WALL
SEEVENT
MANUFACTURER'S
INSTRUCTIONS
MIN 4"
6"
4"
6"
FLOOR PROTECTION
32"
HEAT RADIATION AREA
Fig. 5
REAR WALL
6"
4"
6"
32"
6"
4"
Fig. 6
MIN 22"
(MIN 56 cm)
SIDE WALL
SEE VENT MANUFACTURER'S
INSTRUCTIONS
SIDE WALL

2018PC-03/03
7
FLUEWAY
The stove requires a CE listed pellet vent. Sothe venting system shall be approved for pellet stoves by acertified testing Laboratory.
PL Vent must be used for venting all Freestanding stoves.
Do not use to vent pellet appliance these venting materials and products:
- Dryer vent
- Gas appliance (Type B) vent
- PVC (plastic) pipe
- Single wall stovepipe.
The pellet stove is not the same as other stoves. It has a forced draught of flue gas by a fan, which keeps the firebox in a vacuum
and the entire flueway slightly pressurize. For this reason the flue must be completely airtight and correctly installed to ensure both
trouble-free operation and user safety.
• The flueway must be made by specialized personnel or firms, as outlined below.
• Thefluemustbeinstalledinsuch awayastoguaranteethatperiodiccleaningcan becarriedoutwithoutdismantlinganypartswhatsoever.
• Pipes should always be sealed with silicone (not cement-based sealants) or specially adapted gaskets/seals, which retain their strength and
elasticity athightemperatures(>450°F/230°C),and shouldbefixed withatleast three sheetmetalscrews.
Using the relative pipe clips, fix the flue to the wall so that it does not weigh on the smoke fan.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
Do not connect to a flueway into which extractor hoods discharge vapours.
The very hot exhaust gases may cause skin burns: keep a considerable distance away from the appliance.
The exhaust gases from the combustion of pellets fuel may dirty the outside of the walls.Toavoid such possibility terminate the vent
above the roofline.
Pipes and maximum usable lengths
The exhaust pipe on all stoves is 3” (76 mm) O.D. so the stove was designed to accommodate a 3” stove pipe adaptor but the diameters of the pipes
dependsonthe typeof installation.Yourinstallationmay require theuseof 4”ventas shown inTable1.
TABLE 1: CONNECTION TO FLUE PIPE - PIPE LENGTH
TYPE OF INSTALLATION
WITH 3” DIAMETER PIPE
WITH DOUBLE-WALLED 4”
DIAMETER PIPE
Maximum length (with three 90° elbows)
25’
35’
For installations more than 4000’ (1200 m) above sea level
-
Required
Maximum number of elbows
3
4
Length of horizontal sections with minimum 3% gradient
10’
10’
Losses in pressure associated with a 90° elbow can be compared to those incurred by three feet of pipe. An inspectable union-tee
can be considered equivalent to a 90° bend.
EXAMPLE: if installing a section greater than 20’ in length with 3” diameter pipe, calculate the maximum usable length in the following ways:
•
If a maximum of three 90° elbows are used, the maximum length of the section will be 25’ .
•
If a maximum of two 90° elbows are used and bearing in mind that a 90° bend can be replaced by 3’ of pipe, the maximum length of the section
will be 25’+3’ = 28’ .
• If a maximum of one 90° elbows is used and bearing in mind that a 90° bend can be replaced by one meter of pipe, the maximum length of the
sectionwillbe 25’+3’+3’=31’ .

2018PC-P03/03
8
Fig. 8
Ø 4"
Ø 3"
PELLET
STOVE
TEE W/TEE CAP
Where4”diameterpipemustbeused,connectittothestoveflueoutlet
with a 3” union-tee then use a 3” – 4” (76-102mm) Adapter (Fig. 8).
Union-tee
Theuseofthistypeoffittingmustallowforthecollectionofcondensate
mixed with soot,which builds upinsidethepipe.
It must also permit periodic cleaning of the flue without the need to
disassemble thepipes.
Single or double clean-out tees may be used.
An example is given below of a flueway connection, which allows
complete cleaning without having to disassemble the pipes (Fig. 9).
Fig. 9
INSULATING
MATERIAL
SEE VENT MANUFACTURER'S
INSTRUCTIONS
TEE
DIRECTION
OF CLEANING
0÷ 10'
TEE
MIN 3%
H MIN 13'
H MIN5'
DIRECTION
OF CLEANING
PELLET
STOVE
TEE
DIRECTION
OF CLEANING

2018PC-03/03
9
This kind of installation provides the natural draft that results from
a vertical rise avoiding smoke being released into the house when
electricity to the unit is interrupted while burning or smoldering pellets
remainsintheburngrate.
General vent layout is shown in figure and the procedure is as follows:
Position the appliance in desired location according to appliance
installation requirements.
- Use a plumb line to determine location of PL Vent penetration of
ceiling.
- Cut hole in ceiling and frame to appropriate opening size. Framing
materialshallbe thesame as thatof adjacentjoist material.
- InstallBlackCeilingSupportfrombelow joistlevel andfastenwith4–
1.5” spiral nails or screws (Fig. 10). Alternatively, a Support Assembly
may be used in place of the black ceiling support the support
assembly fits to ceiling opening from below and is fastened to
joists with 4 - 1.5”spiralnailsor screws(Fig.10).
- Insert first Vent section through Support and tighten the clamp screw.
Additionally fasten the vent with four screw (max ½” long) through the
supportcollarandintotheventskin.
- Install the vent section(s) atop the first. Twist lock sections together
with a clock-wise turn. Before twisting, push vent sections firmly
together for proper lock barb engagement. Enough twisting force must
beappliedtoensure thatthecollarswillcompressgasketmaterial.
- Firestops are required where the vent penetrates a floor or ceiling.
Cut a hole of the appropriate size in the ceiling/floor and install the
Firestop from above or below the joist. Fasten the Firestop with nails
through the corners (Fig. 10).
- Elbows may be used to offset the Vent as necessary to jog around
joists or rafters. Keep use of elbows to a minimum as they reduce
draftscapacityofavent.
- Continue the Vent up through the roof line.
- Slide the Flashing over the Vent until it sits on the roof line. Slip the
upper side of the Flashing base under the roof shingles. Nail the
flashing to the roof with a minimum of 8 roofing nails. Seals the
Flashing base with appropriate roofing mastic.
- SlidetheStormCollardowntheVentuntilitsitsontheflashing.Apply
abeadofsiliconearoundthe topof theStormCollar.
- Extend the PL Vent at least 12” above the roof line and terminate with a
PL listed Rain Cap (Fig. 11). If the Vent extends more than 6’ above the
roof penetration, Roof Brace Poles and a Roof Brace Band must be
used to provide lateral support. In geographical regions experiencing
sustained low ambient temperature is recommended to enclose
exterior vents below the roof line. This help reduce condensation, soot
accumulation, and poordrafting.
- Set the Rain Cap onto the topVent section and twist lock it to the top
Vent section (Fig. 11).
- Where the vent system penetrates the air/vapour barrier, the barrier
mustbe sealedtotheceilingsupport orfirestop.
Be sure to use approved pellet vent pipe and ceiling pass-
through fittings to go through combustible ceilings.
Strictly observe the PL Vent manufacturer’s safety
specifications when using ceiling pass through.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
Ensure that all installation work is carried out to professional
standards.
Fig. 10
RAINCAP
STORM COLLAR
FLASHING
SEE VENT
MANUFACTURER'S
INSTRUCTIONS
SEE VENT
MANUFACTURER'S
INSTRUCTIONS
ENCLOSURE
FIRESTOP
BLACK CEILING
SUPPORT
VENT
TEE
FRESH
AIR
INTAKE
Fig. 11
RAINCAP
12" MIN
TOROOF
STORM COLLAR
FLASHING
SEE VENT
MANUFACTURER'S
INSTRUCTIONS
SUPPORT
VENT SECTION
VENT
TEE
FRESH
AIR
INTAKE
English

2018PC-P03/03
10
CONNECTING TO A CONVENTIONAL CHIMNEY
Thestove may be connected toan existing ClassA chimney ora masonry
chimney which meets the minimum requirements of NFPA 211. Using
this kind of installation the pellet stove is able to draft naturally without
exhaust blower operation (failure), reducing the probability of burn-back
and back-drafting.
Check that the connection to the flueway is gas/smoke-tight,
since the appliance operates in a vacuum.
• If you wish to use an existing chimney it is strongly recommended that
you have it checked by a professional chimney sweep to ensure that
it is completely airtight (Fig. 12). The reason for this is that the
smoke, because it is slightly pressurized, can infiltrate any cracks
in the flue and escape into living spaces. If upon inspection you
find that the chimney is not completely sound, a relining of the
chimney with either PL vent or single wall stainless steel pipe may
be necessary to bring the chimney into compliance. If the existing
chimney is wide enough we recommend a pipe with a maximum
diameter of 6”.
Put attention: some areas require that a liner must be always installed
to the top of the flue, as shown in figure even if the existing chimney
is in compliance (Fig. 13).
• When chimneys are relined, a chimney chase cap that reduces the
outlet of the chimney to the size of the liner is required. Extend the
exhaust vent above the chimney chase cap and finish it off with a
rain cap. A single wall liner may need to be insulated to maintain
adequate exhaust temperatures in the vent system.
Outside Chimneys frequently are difficult to keep warm: it is
recommended that you insulate the liner.
•
Venting into the side of an existing masonry chimney must be done
through a masonry thimble. When wall penetration is necessary to
access a masonry chimney, use a listed PL vent wall thimble (Fig.
12-13).
• When venting intoa Class A steel chimney, (Fig. 14), use an appropriate
PL Vent adapter.
Strictly observe the PL Vent manufacturer’s safety
specifications.
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
Ensure that all installation work is carried out to professional
standards.
Fig. 12
MASONARY MUD THIMBLE
PL ADAPTER
VENT
SOOT
INSPECTION
APERTURE
TEE (T)
Fig. 13
MASONRY MUD THIMBLE
PL ADAPTER
SOOT
INSPECTION
APERTURE
VENT
TEE (T)
Fig. 14
SEE VENT
MANUFACTURER'S
INSTRUCTIONS
PL VENT ADAPTER
VENT
TEE
FRESH AIR
INTAKE

2018PC-03/03
11
This kind of installation also provides natural draft in the event of a
power failure.
When installing as a hearth mount stove into a firebox the unit must
either be relined, terminating above the chimney chase top, or positively
connected to the existing chimney system using a block off plate (Fig.
15-16).
An approved flex liner of PL vent must be used.
Put attention:some areas require that a liner must be always installed
to the top of the flue, as shown in figure 16.
A chimney system with known drafting problems may require
a liner, which may also need to be insulated to keep vent
system warm in cold chimney environment.
A cap shall be installed on the chimney to keep out rain.
Strictly observe the PL Vent manufacturer’s safety
specifications.
I NSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
Strictly use listed pellet vent pipe fittings.
Ensure that all installation work is carried out to professional
standards
When terminating the exhaust system under the houses eaves, (Fig. 17)
the following requirements shall be fulfilled:
- in selecting locations for appliance and vent, take into consideration
the NPFA 211 6-3.5 rule for distance of exit terminal from window
andopenings;
- run the vent vertically up the wall,ensuring to maintain a minimum of
3”clearancebetweenthewallandvent;
- a wall band must be installed just above the tee and at least every 6’
of vent rise or,if the rise is inferior, at the end of the vertical run;
- after a rise of at least 5’ (1.5 m) , install a 90° elbow aimed out from
the building wall;
- attach a 45° elbow to the 90° elbow, aiming the second elbow down
toward the ground. Terminate the vent with a collar with screen
fastenedtothe45° elbow;
- the end of the vent pipe system must be at least twelve inches (12”)
from the wall and 24”below the eave.
This configuration will help prevent
blockage of vent by snow drifts. Also the
minimum vertical run of 5 feet (1.5 m)
ensures the ventilation of the exhaust in
the event of a power failure, and allow
for easier cleaning through cleanout on
tee.
-Certain local code restrictions may apply.
Check with Local Officials first before
installing.
-Strictly observe the PL Vent
manufacturer’s safety specifications when using wall pass through.
-INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.
-Double wall PL vent requires a minimum clearance to combustibles
according to the manufacturer’s safety specifications and the use of
listed wall thimble, fire stop or roof flashing where applicable.
-Do not place joints within wall pass throughs.
-Ensure that all installation work is carried out to professional
standards.
Fig. 15
POSITIVE
BLOCK OFF
PLATE TEE
Fig.
16
RAIN CAP
CHIMNEY
FLASHING
PL VENT
SYSTEM
POSITIVE
BLOCKOFF
PLATE
TEE
Fig.
17
TERMINATION
COLLAR
90° ELBOW
WALL BAND
>12
"
> 24"
45°
ELBOW
VENT
>5
'
TEE
English

2018PC-P03/03
12
VENTING:TERMINATION REQUIREMENTS
In determining optimum vent termination, carefully evaluate external
conditions especially when venting directly through a wall. Since you
must deal with odors, gases, and fly ash, consider aesthetics, prevailing
winds, distances from air inlets and combustibles, location of adjacent
structures and any code requirements.
• Exhaust must terminate above combustion air inlet elevation.
• Do not terminate vent in any enclosed or semi-enclosed area, (i.e.
Carports, garage, attic crawl space, etc.) or any location that can build
up a concentration of fumes.
•
Terminalsmust nottoberecessed intoa wallorsiding.
•
When setting into place flue caps you should consider wind factors
such as dominate wind directions and currents in order to avoid down
draft, fly ash and/or smoke.
- Vent surfaces can get hot enough to cause burns if touched
by children.
Non-combustible shielding or guards may be required.
- Be sure to use approved pellet vent pipe and wall pass-
through fittings to go through combustible materials.
The type of installation must first be considered before determining
the exact location of the venting termination in relation ship to doors,
window, cavities or air vents. See figures 18-19.
Without outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
figure 18.
The clearance to a door, window or cavity must be at least:
- 4’ (1.2 m) below;
- 4’ (1.2 m) horizontally;
- 1’ (305 mm) above.
The clearance to fresh air intake for combustion of the pellet stove
or any other appliance, or the non-mechanical air supply inlet to the
building must be at least 4’ (1.2 m).
The clearance to a mechanical air supply inlet to the building must be
at least 10’ (3 m).
With outside combustion air connected to the unit.
For These types of installations please refer to the dimensions listed in
figure 19.
Fig. 18
A= EXHAUST TERMINAL
Fig. 19
A
9"
FRESH AIR
INTAKE
A 4'
1,5'
A
1,5'
9"
1,5'
A
A
MECHANICAL
AIR SUPPLY
INLET
8'
A= EXHAUST TERMINAL
1'
A
4'
4'
FRESH AIR
INTAKE
4'
A
1'
4'
10'
MECHANICAL
AIR SUPPLY INLET

2018PC-03/03
13
The clearance to a door, window or cavity must be at least:
- 1.5’ (458 mm) below;
- 1.5’ (458 mm) horizontally;
- 9’’ (230 mm) above.
The clearance to fresh air intake for combustion of the pellet stove
or any other appliance, or the non-mechanical air supply inlet to the
building must be at least 4’ (1.2 m).
The clearance to a mechanical air supply inlet to the building must be
at least 8’ (2.5 m).
• The exhaust termination location (Fig. 20) must be at least:
- 1’ (305 mm) above the ground level. Attention : the minimum vertical
rise shall always be not less than 5’ (1.5 m).
Aflueat1’abovegroundisnotenfantsafe:westronglyreccomend
that the exhaust termination of flue be raised another 4’ to avoid
injury.
- 7’ (2.1 m) from a public walkway, but attention to where the vent
shall end its course,as it is not to be in between or serve two family
dwellings and/or directly above side-walks or paved driveways;
- 1’ (305 mm) from the wall penetration point;
- 3’ (915 mm) from a gas meter/regulator assembly;
- 3’ (915 mm) from any adjacent combustibles such as:adjacent
buildings, fences, protruding parts of the structure, roof eaves or
overhangs, plants, shrubs, etc.
- The exhaust gases from the combustion of pellets fuel may
dirty the outside of the walls.
To avoid such possibility terminate the vent above the roof
line.
- Ensure that all installation work is carried out to professional
standards.
PREVENTION OF DOMESTIC FIRES
The product must be installed and used in compliance with the manufacturer’s instructions and national standards as well as local regulations.
- When a flue pipe passes through a wall or a ceiling, special installation methods must be applied (protection, thermal insulation,
distances from heat-sensitive materials, etc.) See the paragraph from “INTERIOR VENT INSTALLATION” to “SHORT RISE INSTALLATION
- WALL OUTLET”.
•
It is also recommended that all elements made of combustible or inflammable material, such as beams, wooden furniture, curtaining, flammable
liquids, etc.be kept outside the heat radiation range of the stove and at a distance of at least 32” / 80 cm from the heating block.
•For other information, see the paragraph from “
MINIMUM SAFETY DISTANCES ” to “ VENTING: TERMINATION REQUIREMENTS ”.
• The flue pipe, chimney stack, chimney and fresh air intake must always be free of obstructions, clean and checked periodically, that is, at least
twice during the seasonal period from the lighting of the stove and during its use. When the stove has not been used for some time it is advisable
to carry out the checks mentioned above. For further information, consult a chimney sweep.
•
Only use recommended fuels (See section “FUEL”).
Fig. 20
CLEARANCETO WALL
PENETRATION POINT
1'
CLEARANCE TO
COMBUSTIBLES
CLEARANCE TO
PUBLIC
WALKWAY
7'
3'
45° ELBOW
WITH
TERMINATION
COLLAR
COMBUSTIBLES
THIMBLE
90° ELBOW
1'
PUBLIC
WALKWAY
VENT
CLEARANCE TO
GROUND
TEE
English

2018PC-P03/03
14
MOBILE HOME INSTALLATION
The stove has been tested and listed for mobile home installations.
Unit must be installed in accordance with the: Manufactured Home
and Safety Standard EN14785:2006, CFR
In addition to all previously detailed requirements, mobile home
installations must observe the following:
- Permanently bolt the stove to the floor.Use 4 screws [A] through the
4 holes placed at left and right side in the base plate as shown in
figure 21.
- Electricallygroundthestovetothemetalchassisof thehomeusinga
number8,gaugeor largercopperwire[B].
- Maintain an effective vapor barrier at location where PL vent exits the
structure.
- Floor protection and clearances requirement must be followed
precisely as shown in the previous paragraphs.
- PL Vent must be used for exhaust venting. (Single wall vent is not
allowed). Follow PL Vent manufacturer’s installation directions and
observe all listed clearances to combustibles.
- Check any other local buildings codes or other codes that may apply.
WARNING: DO NOT INSTALL IN A SLEEPING ROOM.
Combustion air must come from the outside of the mobile
home!
Failure to do so may create negative pressure within the
mobile home and could disrupt proper venting and operation
of the pellet stove.
The user must routinely inspect the point where air is drawn
in to insure that itis clear of leaves/debris and ice or snow.
CAUTION: THE STRUCTURAL INTEGRITY OF THE FLOORS,
WALLS, CEILING AND ROOF MUST BE MAINTAINED.
The stove is hot while running. Keep children, clothing and
furniture away. Contact may cause skin burns.
Keep combustible materials such as grass, leaves, etc. at
least 4ft away from the point directly under the vent
termination.
Fig. 21

2018PC-03/03
15
2.0 TECHNICAL CHARACTERISTICSAND SPECIFICATIONS
Features
Cladding: .......................... Printed steel with majolica insert
Interior:............................. steel
Baffle plate and hearth:..... cast iron
Grate: ............................... cast iron
Door: ................................ Printed steel with double ceramic glass heat resistant up to 1382°F / (750°C)
Handle: ............................. in printed steel
Control panel: ................... LCD color touch screen with remote control
Timer thermostat:.............standard with daily, weekly and weekend programming modes divided into four time period
Power setting:...................from 1 to 4
Ash Clean: ...................... Automatic ash cleaning
Ash drawer: ...................... removable
Fuel: ................................. natural pure wood pellets (see section “FUEL”)
Heating:............................ forced ventilation
TEChNICAL DATA
model
PC-P03
Heat input
kW/h
6-11
Pellet consumption per hour
kg/h
0.6-2.2
Overall efficiency
%
≥90
Rated current during ignition
A
1.2
Maximum power input during ignition
W
248
Maximum power input at work
W
68
Electrical power supply voltage
V
230
Rated frequency
Hz
50
Fuel tank capacity
kg
21
Fuel size
mm
D6-8/L10-40
Exhaust outlet diameter
mm
Ø 76
Max heating area
m²
110
Weight with cladding
kg
90
Packing sizes (HxWxD)
cm
985x520x550
N.B.: The above data may vary according to the characteristics of the pellets being used. (See section “FUEL”).
ACCESSORIES AND EQUIPMENT
Description
NTC 10K room temperature sensor
In kit
Flexible cable L = 4.9’ / (150 cm)
In kit
Door handle tool
In kit
Grate baffle plate
In kit
User’s manual
In kit
Remote control
In kit
Ash cleaning kit
optional
Maintenance tools kit
optional
English

2018PC-P03/03
16
DIMENSIONAL DIAGRAM
Fig.22
Unit = mm

2018PC-03/03
17
WIRING DIAGRAM
Fig.23

2018PC-P03/03
18
3.0 FUEL
The wood pellet is obtained by pressing wood sawdust left over from
the working of natural dried wood. The typical small, cylindrical form is
obtained by passing the material through a die.Thanks to lignin,a natural
element which is released during the pressing of the raw material, the
pellets acquire a good consistency and compactness without requiring
treatment with additives or caking agents.
There are various types of pellet on the market with qualities and
characteristics that vary depending on the processes they have
undergone and the type of wood used in their production.
Since the characteristics and quality of the pellet considerably
affect stove performance, efficiency and proper operation, we
recommend that you use high-quality pellets.
Manufacturer and distributor has tested and programmed its
stoves and can ensure best performance and trouble-free
operation using pellets with the following specific
characteristics:
Pellet characteristics
Components
natural pure wood pellet
Length, approx.
¼” – 1 ¼” / (7 – 30 mm)
Diameter, approx.
0.23” – 0.25” / (6 – 6.5 mm)
Apparent density, approx.
40.5 lb/ft3/ (650 kg/m3)
Net heat value, approx.
8000 BTU/lb / (5 kWh/kg)
Moisture content, approx.
< 8%
Residual ash, approx.
< 0.5%
N.B. the above data refer to beech/fir wood pellets
To ensure trouble-free operation:
DO NOT use pellets with dimensions other than those recommended by
the manufacturer.
DO NOT use poor quality pellets containing sawdust, bark, maize, resins
or chemical substances, additives or adhesives.
DO NOT use damp pellets.
Choosing other and unsuitable pellets
- obstructs the grate and flue gas pipes;
- increases fuelconsumption;
- reduces efficiency;
- means that proper stove operation cannot be guaranteed;
- causes dirt to build up on the glass;
- leaves particles which have failed to burn and heavy cinders.
The presence of moisture in the pellets increases their volume and
causes them to split which in turn causes:
- malfunction of the fuel-loading system;
- inefficient combustion.
Pellets should be stored in a sheltered, dry place.
To use good quality pellets with dimensions and heat-producing
properties other than those recommended above, it will be necessary to
change the stove operating parameters.
The use of cordwood is prohibited. Do not burn garbage or
flammable fluids such as gasoline, naphtha or engine oil.
This “customisation” of stove settings must be carried out by
authorisedpersonnel by distributor
Using pellets that are out of date or not in conformity with
the manufacturer’s recommendations not only damages the
stove and jeopardises its performance, but can render the
guarantee null and void and relieves the manufacturer of all
liability.
4.0 PREPARING FOR INSTALLATION
To prevent accidents or damage to the product we recommend the
following:
- unpacking and installation must be carried out by at least two people;
- every operation involving movement of the product must be carried
out with the proper tools in full compliance with current safety
regulations;
- the packaged product must be kept in the position according to the
directions shown by the diagrams and notices on the pack;
- if ropes, straps or chains are used, ensure that they are able to take
the weight of the pack and that they are in good condition;
- never stand in the vicinity of loading/unloading equipment (forklift trucks, cranes etc);
Unpack the product being careful not to damage or scratch it, take the accessories pack and any pieces of polystyrene or cardboard
used to wedge moveable parts etc. out of the stove firebox. Keep packaging (plastic bags, polystyrene, etc.) out of reach of children,
since it could be a potential source of danger, and dispose of according to local regulations.
To make moving and handling of the stove easier for installation purposes, it is advisable to remove the cladding in accordance with
the procedure described in the paragraph “REMOVING THE CLADDING” and then refit it upon completion of installation. If you decide
to install the stove without removing the cladding, take great care not to buckle, scratch or in any way damage the bottom of the side
panels and the lower frontpanel.
Installation and assembly of the stove must be carried out by qualified personnel.
English

2018PC-03/03
19
5.0 USE
The pellet stove is a different type of heater. Its operation and maintenance differ from the traditional wood stove. Follow these operating instructions
exactly as stated to ensure safe and reliable operation.
• Do not use the stove as a cooking appliance.
•
Ensurethatthe roominwhichthestove isinstalled issufficientlywellventilated(freshairintake).
•
A certain amount of carbon monoxide may be produced within the stove as a by-product of combustion.All exhaust vent connections must be
sealed withRTV siliconeto assure agastightseal.Anyleaks intoa confined areacausedby faultyinstallationorimproperoperationofthestove
could produce dizziness, nausea and in extreme cases, death.
•
Check (or have checked) regularly that the flue is clean.
• Under no circumstances use fuels other than pellets.
•
Remove any deposits of unused pellets left by failed ignition before restarting the stove.
Direct contact with the stove while operating may cause skin burns.
During operation some parts of the stove (door, handle, controls, ceramic parts) can reach high temperatures. Take great care and all
the necessary precautions, especially in the presence of children, the elderly or disabled and pets.
Keep any inflammable object well away from the stove while it is in use (MINIMUM 32” -80 cm) from the front panel.
While in use the door must remain closed and the glass must be present and intact.
The removal of the protective grille inside the pellet hopper is strictly prohibited.
If replenishing with pellets while the stove is lit, ensure that the bag does not come into contact with any hot surfaces.
Operate this unit only with the fuel hopper lid closed. Failure to do so may result in emission of products of combustion from the
hopper under certain conditions. Maintain hopper seal in good condition.
LOADINGTHEPELLETS
• When lighting your stove for the first time, or any time you have run
out of Pellets, you will need to fill the hopper. Pellets are fed from the
hopper to the burn pot by an auger.A high torque motor that is capable
of doing serious harm to fingers drives the auger and for this reason in
the pellet stoves a protective grille inside the hopper is placed.
Don’t remove the protective grill inside the pellet hopper.
•
Toloadthepelletsintothehopper itisadvisabletotearofftheedgeof
the sack and empty the sack directly into the hopper.This makes filling
easier and avoids pouring pellets on top of the stove.
Do not allow sawdust to accumulate on the bottom of the
hopper.
Do not leave leftover pellets on top of the stove – they could
catch fire!
Do not overfill hopper.
Maintain hopper seal in good condition.
DO NOT RELOAD WITH PELLETS WHEN THE APPLIANCE IS LIT if
the red reload indicator inside the pellet hopper is visible (see
figure to the side).
To load with pellets if the red reload indicator is visible, proceed as
follows:
- shut down the appliance;
- load the hopper as described above.
The auger must have the time to fill; during this stage the pellets are
not distributed inside the firebox and it is more than likely that the first
attempt to ignite the appliance fails; empty and clean the great. Lighting
again the stove.
If an alarm is triggered, deactivate the appliance by pressing the ON/OFF
key for a few moments, remove the fuel to be found in the grate and set
a new ignitioncycle.
Any unburned pellets to be found in the grate must be disposed of.
Fig. 24

20
6.0 PRODUCT & CONTROL SYSTEM
①Control panel
②Power switch (back side )
③Pellets hopper
④Hot air outlet
⑤Combustor doorknob
⑥Feeding hole
⑦Fire box
⑧Ash tray
⑨Ash cleaning rod
6.1 Product overview
Fig. 24