Pinnacle Outdoor FOWLHOUSE User manual

FOWLHOUSE
1.5W x 1.4D x 2.0Hm
Tools required: Drill, measuring tape, Phillips-head screw driver, rivet gun, rubber mallet, sturdy ladder, shifting spanner, 2 saw horses, 3mm
steel drill bit and a 4mm steel drill bit.
Assembly instructions
Congratulations on purchasing your new Pinnacle fowl house. Before assembling, we recommend
you read the instructions thoroughly.Your new fowl house comes with pre-drilled holes to make assembly
quicker. We recommend you assemble the fowl house using a trestle table or sawhorses and planks.
This will ensure that you are working off the ground and make it easier for you. Assembly is a two-person
job and should not be attempted in windy conditions.

FOWLHOUSE1.5 x 1.4 x 2.0m
Build your fowl house in 7 easy steps!
Step 1: Check all parts against the component list
Step 2: Assemble the rear wall panels
Step 3: Assemble the side wall panels
Step 4: Assemble the roof panels
Step 5: Assemble the front wall panel
Step 6: Attach the front door
Step 7: Fit the panels together
IMPORTANT: It is recommended that your new fowl house is secured to a concrete slab as per the specifications in this manual.
Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builder’s
plastic and F52 reinforcing mesh. We recommend that you make your slab approximately 100mm bigger than the base
dimensions of your fowl house. This will allow for a 50mm edge around your fowl house. We recommend that you slope the
50mm edges downward by 10mm so that rain water can drain away from your fowl house.
1500mm

Step 1: Check all parts against the component list
Lay out all parts with number facing outwards and check off against parts list.
Picture Description Component Location Part
No. QTY Check
Sheet Sheet 1800x770mm Rear wall S75 2
Sheet
Sheet
Sheet 1800x708mm Side Wall
Side Wall
S77 1
Sheet 1800x708mm
Sheet 810x708mm
S78 1
Side Wall
Sheet
Side Wall
Sheet
1800x708mm
1800x708mm
1800x708mm
Side Wall
Side Wall
S79L
S79R
1
1
Front Wall
Sheet
Door
Front
Door
S80 1
1745 x 770mm D33 1
Sheet Roof S81 2
Sheet 810x708mm
Sheet Roof S82 2

1.5 x 1.4 x 2.0mFOWLHOUSE
Picture Description Component Location Part
No. QTY Check
Channel Channel 1508mm Rear Wall 20C 1
Channel Channel 1508mm Rear Wall 20V 1
Roof 36C 2
Side Wall 36E 1
Side Wall 36F 1
Side Wall
Front C121 3
Front 23 1
Front J36 1
Front 42 1
Z34 2
Roof Side
Wall 36A 4Channel Channel 1391mm
Channel Channel 1391mm
Channel Channel 1391mm
Channel Channel 1391mm
Channel Channel 652mm
Channel Channel 775mm
Jamb
Jamb
Jamb
Jamb 1798mm
Jamb 775mm
Jamb 1798
Channel Channel 1508mm 20T 1
Channel Channel 1508mm Front
Front
20U 1
Corner

Picture Description Component Location Part
No. QTY Check
Roof
Corner
Corner
SL08 4
Roof 92 1
Roof 93 1
Roof SG27 2
Roof SG28 2
Roof
Roof
E1 2
65 2
Z35 1
1
Jamb Jamb 1898
Z36Jamb Jamb 1898
Lip Lip 812mm
Ridge Beam Ridge Beam 1393
Gable R/H Gable 734
Gable L/H Gable 734
Logo Cap Logo Cap
Roof Brace Roof Brace
Connector Gable Cap Connector
1393

1.5 x 1.4 x 2.0mFOWLHOUSE
Fittings part list:
Picture Component QTY Picture Component QTY √
Self tapping screws (10mm) 140 Self tapping screws (16mm) 50
4 x 10mm Rivet 6 3 x 10mm Rivet 35
Pad bolt (70) 1Keeper (71) 1
Qty checking date: ____ / ____ / _____
Qty checking personal badge number: _______________
Signature: _________________________________________
In the unlikely event that you find you are missing a part, please contact Pinnacle at 1800 349 776. A copy of proof of purchase may be requested.
CAUTION:Birds can be susceptible to heavy metal poisoning from zinc/galvanised coatings.Please check that our metal
fowl houses are suitablefor your pet. Refer to your local vet for further information.
IMPORTANT: Scrub the mesh with a mild solution of vinegar (2 cups in a bucket of water) and then rinse with clean water.
This will remove excess zinc that could potentially cause harm to pets.

Fowl house overview:

1.5 x 1.4 x 2.0mFOWLHOUSE
Step 2: Assemble the rear wall panels
For easier assembly of your fowl house use sawhorses with timber studs as per diagram below (timber needs to be the same length
as the fowl house (1.5 M)) or alternatively, a trestle table.
Place 2 x part S75 (sheets) on your worktable and join together with the self-tapping screws as per the diagram below.
Now fit part 20V (top channel) and 20C (bottom channel) to the sheeting by tapping it in (diagram A) or sliding it in (diagram B).
Make sure the small lip of the channel is always facing out. This ensures rainwater cannot build up inside your fowl house.
8

9
Step 2: Assemble the rear wall panels (continued)
NOTE: All screws marked with a cross should not be fixed at this stage.

1.5 x 1.4 x 2.0mFOWLHOUSE
10
Step 3: Assemble the side wall panels
Place parts S77 & S79L (sheets) on your worktable and tap or slide on part 36F (top channel) and part 36A (bottom channel).
Make sure the small lip of the channels is always facing out. This ensures rainwater cannot build up inside your fowl house.
Once the top and bottom channels have been fixed, attach the channel (C121) above the mesh on part S79L (sheet) with the
provided 3 x 10mm rivets. NOTE:All screws marked with a cross should not be fixed at this stage.
FIX WITH
16MM SCREWS
FIX WITH 3 X 10MM RIVET
BACK