Pinpoint Mounts AM-20 User manual

AM-20
UNIVERSAL SPEAKER MOUNT
A
B
C
D
Standard Wall Mount
Configuration
For mounting to solid wall surfaces such as wood stud, drywall or masonry (concrete).
Electrical Box Wall Mount
Configuration
For mounting to a standard single gang electrical box located on a wall in pre-wired homes.
Standard Ceiling Mount
Configuration
For mounting to solid ceiling surfaces such as wood stud, drywall or masonry (concrete).
Electrical Box Ceiling Mount
Configuration
For mounting to a standard single gang electrical box located on a ceiling in pre-wired homes.
The AM-20 Speaker Mount has been designed to offer 4 different configurations for mounting home theater speakers and can be used as a wall or ceiling mount. It is pre assembled in the Standard Wall Mount Configuration (A) shown, but can be assembled to any of the 3 additional configurations (B,C,D) shown. Just select the configuration best suited for your application and follow the assembly instructions on pages 2-4. The AM-20 can support speakers up to 12 lbs (5.44kg) in all configurations and offers a full tilt
and swivel adjustability.
X 2 (wood screw)
X 2 (Electrical Box Screw)
X 1 (1/4-20 x 1”) X 1 (6mm x 25mm) X 1 (5mm x 25mm)
X 2 (1/4-20 x .47”) X 2 (6mm x 12mm) X 2 (5mm x 12mm)
X 1 (5mm Key hole Adapter)
X 2 (Large Washer)
X 1 (Small Washer) X 1 (Split Washer)
A B C D E F G H IJK L M
X 1 (Allen Key)
X 1 (Electrical Box Plate)
X 1 (Long Post)
X 1 (Dual Point Adapter)
X 2 (Plastic Cover Half)
S
OPQR
P. 1/4
PARTS
A
B
360°
90°
E
F
D
F
360°
B
C
90°
360°
360°
12
34A
B
C
D
E
F
4.05”103.0mm 4.52”115.0mm 5.31”135.0mm 1.18”30.0mm 3.30”84.0mm 2.83”72.0mm
A
B
360°
90°
E
F
D
F
B
C
90°
360°
360°
360°
1
3
2
4A
B
C
D
E
F
3.66”93.0mm 3.62”92.0mm 5.51”140.0mm 1.37”35.0mm 3.42”87.0mm 1.96”50.0mm
www.pinpointmounts.com 11157 Outlet Dr. Knoxville TN 37932 [phone]
NOTICE!
If you have any questions on the installation, assembly, or
have missing or damaged parts, please contact our support team
at [phone] Monday-Friday 9.30a - 5.30p or by email 24/7
at [email protected].
REV. 2-9/10
X 1 (1/4-20 x 1.75”)
T (Wrench)

14mm
9/16” 7
6
5
Q
34
12
P
PRE-WIRED CEILING MOUNT
D
14mm
9/16” 7
6
5
Q
34
12
STANDARD CEILING MOUNT
C
14mm
9/16”
123
P
PRE-WIRED CEILING MOUNT
B
1
STANDARD WALL MOUNT
A
Choose the mounting configuration needed for your application from the diagrams on this page then continue to the next page. Note: Over tightening the set screws may cause cross threading or stripped threads.
SPEAKER MOUNT CONFIGURATION ASSEMBLY
P. 2/4
Use the included wrench to remove the nut holding the mount to the wall plate. You can also use a 14mm socket wrench.
T

MOUNTING TO A CEILING LOCATION
FOLLOW DIAGRAM A WHEN MOUNTING
TO A STANDARD SINGLE GANG
ELECTRICAL BOX.
FOLLOW DIAGRAM B WHEN MOUNTING
TO A SOLID SURFACE LOCATION.
MOUNTING TO A WALL LOCATION
FOLLOW DIAGRAM A WHEN MOUNTING
TO A STANDARD SINGLE GANG
ELECTRICAL BOX.
FOLLOW DIAGRAM B WHEN MOUNTING
TO A SOLID SURFACE LOCATION.
A A
SINGLE
ELECTRICAL
BOX
BB
WOOD STUD
ELECTRICAL BOX
A
B
A
A
SINGLE
ELECTRICAL
BOX
B
B
WOOD STUD
ELECTRICAL BOX
AB
WARNING! - When mounting this product it is recommended to determine the location selected will support at least two times (2x)
the total weight of the speaker. When mounting this product to a electrical box location, inspect this location to determine if the box
is properly attached to a support stud (2x4’) with screw/nail & the drywall is in good condition.
ATTACHING THE MOUNT
P. 3/4
To insure proper mounting and maximum security, it is recommended that this
mount is installed into a wood joist/stud or other solid surface that will support
at a minimum, 2 times the total weight of the speaker.
If installation requires the use of drywall anchors (not included) please select
quality anchors that best fits the mounting needs of the drywall and can support
3 times the weight of the speaker.
WARNING!
Installing the mount to ceiling.
1. Select location for installation using a stud finder to locate the center of
the wood stud/joist. Mark location for holes using the mount as a template.
2. Pre-Drill 2 pilot holes using a 1/8” drill bit. Take care when drilling to avoid
any wires or pipes that may be behind the wall/ceiling. (Drywall mounting
will follow instructions of anchors)
3. Using the 2 supplied wood screws (Part A) attach the bracket using a #2
Philips screw driver or driver bit (avoid over tightening to prevent stripping
the screw head).
4. Once the bracket is mounted, replace the 2 plastic cover plates.
If you have questions on these steps, please contact us.
To insure proper mounting and maximum security, it is recommended that this
mount is installed into a wood joist/stud or other solid surface that will support
at a minimum, 2 times the total weight of the speaker.
If installation requires the use of drywall anchors (not included) please select
quality anchors that best fits the mounting needs of the drywall and can support
3 times the weight of the speaker.
WARNING!
Installing the mount to ceiling.
1. Select location for installation using a stud finder to locate the center of
the wood stud/joist. Mark location for holes using the mount as a template.
2. Pre-Drill 2 pilot holes using a 1/8” drill bit. Take care when drilling to avoid
any wires or pipes that may be behind the wall/ceiling. (Drywall mounting
will follow instructions of anchors)
3. Using the 2 supplied wood screws (Part A) attach the bracket using a #2
Philips screw driver or driver bit (avoid over tightening to prevent stripping
the screw head).
4. Once the bracket is mounted, replace the 2 plastic cover plates.
If you have questions on these steps, please contact us.

P. 4/4
(D,K,L & R)
DUAL MOUNTING POINTS
F,G or H
F,G or H
J
J
D
L
K
R
SINGLE MOUNTING POINT
C,D,M or E
L
K
(C,D or E & K,L)
KEYHOLE MOUNTING POINT
E
L
K
I
or
L
E
K
I
or
(E,K,L,I)
(I,K,L,E)
2.67” (68mm) Max
1.96” (50mm) Min
To mount a speaker, remove the single point
adapter tip(A) from the Mounting body(B) and
determine the correct speaker mounting point
your speaker has from the three (3) diagrams
shown in step 3.
-Some speakers may use more than one type
of mounting point, select the one best suited
for your application.
-The hardware kit supplied with this mount are
contains the most common size screws used
to mount speakers. Some speakers may
require longer or shorter screws not supplied
in this kit.
A
B
Once the speaker has been attached
to the adapter tip(A), replace the adapter
tip(A) to the mounting body(B) and then
attach the adapter body(B) to the speaker
mount assembly(C).
AB
C
Step 2
Step 3
After the speaker has been attached
to the speaker mount assembly, you
should connect the speaker wires.
To aim the speaker, loosen the small
allen key bolts (C1) so that the adapter
body can be rotated & tilted to the
desired position. Tighten the allen key
bolts(C1) to lock the speaker into the
desired position.
C1
MOUNTING THE SPEAKER
Step 1
Before installing the speaker, remove
the mounting tip assembly(1) from the
mounting bracket body(2).
1
2
Step 2
Step 4
Step 4