Pioneer GM-D9500F User manual

----------------------m
=
CQ
-
_.
f/I
:::r'
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE PONTABLE AQUATRE VOlES
AMPLIFICADOR DE POTENCIA DE CUATRO CANALES EN PUENTE
GM-D9500F
Owner's Manual
Mode d'emploi
Manual de instrucciones
-
----------------------m
=
CQ
-
_.
f/I
:::r'
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE PONTABLE AQUATRE VOlES
AMPLIFICADOR DE POTENCIA DE CUATRO CANALES EN PUENTE
GM-D9500F
Owner's Manual
Mode d'emploi
Manual de instrucciones
-

• (contents
'.;:
-{:c_
~ Before you start
Information to User 3
A.ftel"sales service for Pioneer products 3
Visit our website 3
Before connecting/installing the amplifier 4
~ Setting the Unit
What's what 5
Setting gain properly 5
~ Connecting the units
Connection diagram 7
Before connecting the amplifier 7
About bridged mode 8
About suitable specification of speaker 8
Connecting the speakers 8
Connections when using the RCA Input
jack 10
Connections when using the speak.er input
'vVlre 10
Connecting the power terminal 11
Connecting the speaker output
terminals 12
~ Installation
Before installing the amplifier 13
Example of installation on the floor mat or
chassis
13
•Additional information
Specifications 14
r;;\
~~ En
• (contents
'.;:
-{:c_
~ Before you start
Information to User 3
A.ftel"sales service for Pioneer products 3
Visit our website 3
Before connecting/installing the amplifier 4
~ Setting the Unit
What's what 5
Setting gain properly 5
~ Connecting the units
Connection diagram 7
Before connecting the amplifier 7
About bridged mode 8
About suitable specification of speaker 8
Connecting the speakers 8
Connections when using the RCA Input
jack 10
Connections when using the speak.er input
'vVlre 10
Connecting the power terminal 11
Connecting the speaker output
terminals 12
~ Installation
Before installing the amplifier 13
Example of installation on the floor mat or
chassis
13
•Additional information
Specifications 14
r;;\
~~ En

C,,--B_e_f_or_e--=y=---o_u_s_t_a_rt ~)
section
C ) (II
Thank you for purchasing this PIONEER pro-
duct. It is designed to give you many years of
enjoyment.
PIONEER SUGGESTS USING A PROFES-
SIONAL INSTALLER DUE TO THE COMPLEX-
11Y OF THIS PRODUCT. Please read all
instructions
and WARNINGS in this manual
before attempting operation. Should
you have
any questions, contact your nearest Pioneer
authorized dealer or installation specialist. (!)
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user's right to operate the equipment.
After-sales service for
Pioneer produds
Please contact the dealer or distributor from
where
you purchased this unit for after-sales
service (including warranty conditions) or any
other information.
In case the necessary infor-
mation
is not available, please contact the
companies listed
below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R OP2
1-877 - 283-5901
905-479-4411
For warranty information please see the lim-
ited Warranty sheet included with this unit.(!)
Visit ourwebsite
Visit us at the following site:
http://www.pioneerelectronics.com
1 Register your product. We will keep the details
of your purchase on file to help you refer to
this information in the event of an insurance
clai m such as loss or theft.
2 Receive updates on the latest products and
technologies.
3 Download owner's manuals. order product
catalogues. research new products, and
much more.C!J
m
:::J
cc
-
iii'
:::J"
En (])
C,,--B_e_f_or_e--=y=---o_u_s_t_a_rt ~)
section
C ) (II
Thank you for purchasing this PIONEER pro-
duct. It is designed to give you many years of
enjoyment.
PIONEER SUGGESTS USING A PROFES-
SIONAL INSTALLER DUE TO THE COMPLEX-
11Y OF THIS PRODUCT. Please read all
instructions
and WARNINGS in this manual
before attempting operation. Should
you have
any questions, contact your nearest Pioneer
authorized dealer or installation specialist. (!)
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user's right to operate the equipment.
After-sales service for
Pioneer produds
Please contact the dealer or distributor from
where
you purchased this unit for after-sales
service (including warranty conditions) or any
other information.
In case the necessary infor-
mation
is not available, please contact the
companies listed
below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R OP2
1-877 - 283-5901
905-479-4411
For warranty information please see the lim-
ited Warranty sheet included with this unit.(!)
Visit ourwebsite
Visit us at the following site:
http://www.pioneerelectronics.com
1 Register your product. We will keep the details
of your purchase on file to help you refer to
this information in the event of an insurance
clai m such as loss or theft.
2 Receive updates on the latest products and
technologies.
3 Download owner's manuals. order product
catalogues. research new products, and
much more.C!J
m
:::J
cc
-
iii'
:::J"
En (])

section
ED (Before you start
)c )
Before connedingl
installing the amplifier
AWARNING
•Handling the cord on this product or cords as-
sociated with accessories sold with the pro-
duct will expose you to chemicals listed on
proposition
65 known to the State of California
and other governmental entities to cause can-
cer and birth defect orother reproductive
harm.
Wash hands after handling.
• The use of aspecial red battery and ground
wire
RD-223, available separately, is recom-
mended. Connect the battery wire directlyto
the car battery positive terminal ®and the
ground wire
to the car body.
•This unit is for vehicles with a 12 Vbattery and
negative grounding. Before installing in
re-
creational vehicles, trucks or buses, check the
battery voltage,
•The black cable is ground. When installing
this unit, make sure to connect the ground
wire first. Ensure that the ground wire is prop-
erly connected to metal parts of the car's
body. The ground wire of the one of this unit
must
be connected to the car separately with
different screws. If the screw forthe ground
wire loosens or falls out, it could result in fire,
generation of smoke or malfunction.
•Use afuse of the rating prescribed.
•Check the connections of the power supply
and speakers if the fuse of the separately sold
batterywire orthe amplifier fuse blows. Deter-
mine and resolve the cause, then replace the
fuse with identical equivalent.
•Always install the amplifier on aflat surface.
Do not install the amplifier on asurface that
is not flat oron asurface with aprotrusion.
Doing so could result in malfunction.
•When installing the amplifier, do not allow
parts such
as extra screws to get caught be-
tween the amplifier and the automobile.
Doing so could cause malfunction.
CD En
• Do not allowthis unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and
over-
heating could result from contact with liquids.
The surfaces of the amplifier and any attached
speakers may also heat up and cause
minor
burns.
•
In the event of any abnormality, the power
supply to the amplifier is
cut off to prevent
equipment malfunction. If this occurs, switch
the system power
OFF and check the power
supply and speaker connections. If
you are un-
able to determine
the cause, please contact
your dealer.
•Disconnect the negative terminal of the bat-
tery before installation.
ACAUTION
•Always keep the volume low enough to hear
outside sounds.
•Extended use of the car stereo while the en-
gine is at rest or idling may exhaust the bat-
tery.
'-' Important (Serial number)
The serial number is located on the bottom of
this unit.
For your own security and convenience,
be sure to record this number on the enclosed
warranty
card.~
section
ED (Before you start
)c )
Before connedingl
installing the amplifier
AWARNING
•Handling the cord on this product or cords as-
sociated with accessories sold with the pro-
duct will expose you to chemicals listed on
proposition
65 known to the State of California
and other governmental entities to cause can-
cer and birth defect orother reproductive
harm.
Wash hands after handling.
• The use of aspecial red battery and ground
wire
RD-223, available separately, is recom-
mended. Connect the battery wire directlyto
the car battery positive terminal ®and the
ground wire
to the car body.
•This unit is for vehicles with a 12 Vbattery and
negative grounding. Before installing in
re-
creational vehicles, trucks or buses, check the
battery voltage,
•The black cable is ground. When installing
this unit, make sure to connect the ground
wire first. Ensure that the ground wire is prop-
erly connected to metal parts of the car's
body. The ground wire of the one of this unit
must
be connected to the car separately with
different screws. If the screw forthe ground
wire loosens or falls out, it could result in fire,
generation of smoke or malfunction.
•Use afuse of the rating prescribed.
•Check the connections of the power supply
and speakers if the fuse of the separately sold
batterywire orthe amplifier fuse blows. Deter-
mine and resolve the cause, then replace the
fuse with identical equivalent.
•Always install the amplifier on aflat surface.
Do not install the amplifier on asurface that
is not flat oron asurface with aprotrusion.
Doing so could result in malfunction.
•When installing the amplifier, do not allow
parts such
as extra screws to get caught be-
tween the amplifier and the automobile.
Doing so could cause malfunction.
CD En
• Do not allowthis unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and
over-
heating could result from contact with liquids.
The surfaces of the amplifier and any attached
speakers may also heat up and cause
minor
burns.
•
In the event of any abnormality, the power
supply to the amplifier is
cut off to prevent
equipment malfunction. If this occurs, switch
the system power
OFF and check the power
supply and speaker connections. If
you are un-
able to determine
the cause, please contact
your dealer.
•Disconnect the negative terminal of the bat-
tery before installation.
ACAUTION
•Always keep the volume low enough to hear
outside sounds.
•Extended use of the car stereo while the en-
gine is at rest or idling may exhaust the bat-
tery.
'-' Important (Serial number)
The serial number is located on the bottom of
this unit.
For your own security and convenience,
be sure to record this number on the enclosed
warranty
card.~

C S_e_tt_in---=g=--t_h_e_u_n_it )SectIon
C ) &I
What's what
Front side
Rear side
.,.-±rJ
~
"--~~~~~@~~:I~ ~~ ~ - ---.-_...... ~
._ ...
2 3 4 5
To adjust the switch, use aflathead screwdri-
ver if needed.
CD Power indicator
The power indicator lights up to indicate
power ON.
tIl GAIN (gain) control
Adjusting gain controls CHANNEL A(chan-
nel
A) and CHANNEL B(channel B) helps
align the car stereo outputto the Pioneer
amplifier. Default setting
is the NORMAL
position.
If output remains
low, even when the car
stereo volume
is turned up, turn controls to
lower level. If distortion occurs when the car
stereo volume
is turned up, turn these con-
trols to higher level.
•If using only one input plug, set the gain
controls for speaker outputs Aand Bto
the same position.
•
For use with an RCA equipped car stereo
(standard output of
500 mV), set to the
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with max.
output of 4 V or more, adjust level to
match that of the car stereo output.
®lPF (low-pass filter)/HPF (high-pass fil-
ter)
select switch
Switch the settings based on the connected
speaker.
•When the Subwoofer is connected:
Select lPF. This eliminates high range
frequency and outputs low range fre-
quency.
•When the full range speaker is con-
nected:
Select
HPF or OFF. HPF eliminates low
range frequency and output high range
frequency.
OFF outputs the entire fre-
quency range.
@ FREQ (cut off frequency) control
Cut off frequency selectable from 40 Hz to
500 Hz if the lPF/HPF select switch is set to
lPF or HPF.
® INPUT SELECT (input select) switch
Select 2CH for two-channel input and 4CH
for four-channel input. ~
Setting gain properly
•Protective function included to prevent
malfunction of the
unit and/or speakers
due to excessive output, improper use or
improper connection.
•When outputting high volume sound etc.,
this function cuts off the output for afew
seconds as anormal function, but output
is restored when the volume of the head
unit is turned down.
En CD
C S_e_tt_in---=g=--t_h_e_u_n_it )SectIon
C ) &I
What's what
Front side
Rear side
.,.-±rJ
~
"--~~~~~@~~:I~ ~~ ~ - ---.-_...... ~
._ ...
2 3 4 5
To adjust the switch, use aflathead screwdri-
ver if needed.
CD Power indicator
The power indicator lights up to indicate
power ON.
tIl GAIN (gain) control
Adjusting gain controls CHANNEL A(chan-
nel
A) and CHANNEL B(channel B) helps
align the car stereo outputto the Pioneer
amplifier. Default setting
is the NORMAL
position.
If output remains
low, even when the car
stereo volume
is turned up, turn controls to
lower level. If distortion occurs when the car
stereo volume
is turned up, turn these con-
trols to higher level.
•If using only one input plug, set the gain
controls for speaker outputs Aand Bto
the same position.
•
For use with an RCA equipped car stereo
(standard output of
500 mV), set to the
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with max.
output of 4 V or more, adjust level to
match that of the car stereo output.
®lPF (low-pass filter)/HPF (high-pass fil-
ter)
select switch
Switch the settings based on the connected
speaker.
•When the Subwoofer is connected:
Select lPF. This eliminates high range
frequency and outputs low range fre-
quency.
•When the full range speaker is con-
nected:
Select
HPF or OFF. HPF eliminates low
range frequency and output high range
frequency.
OFF outputs the entire fre-
quency range.
@ FREQ (cut off frequency) control
Cut off frequency selectable from 40 Hz to
500 Hz if the lPF/HPF select switch is set to
lPF or HPF.
® INPUT SELECT (input select) switch
Select 2CH for two-channel input and 4CH
for four-channel input. ~
Setting gain properly
•Protective function included to prevent
malfunction of the
unit and/or speakers
due to excessive output, improper use or
improper connection.
•When outputting high volume sound etc.,
this function cuts off the output for afew
seconds as anormal function, but output
is restored when the volume of the head
unit is turned down.
En CD

section
m( Setting the Unit
)c)
Amplifier gain ... ~ Amplifier gain
(normal) (maximum)
Signal waveform when outputting at
high volume using amplifier gain
control
IMaximum gain I
Signal
waveform
........ Equal power·"
INormal gain
Signal waveform distorted with high output, if
you raise the gain of the amplifier the power
changes only slightly.
C!J
• A cut in sound output may indicate impro-
per setting of the gain control.
To ensure
continuous sound output with the head
unit at ahigh volume, set amplifier gain
control to alevel appropriate
for the preout
maximum output level of the head unit,
so
that volume can remain unchanged and to
control excess output.
•Despite correct volume and gain settings,
the
unit sound still cuts out periodically. In
such cases, please contact the nearest
authorized Pioneer Service Station.
Gain control of this unit
NORMAL
.--~
Preout level: 2 V
(Standard: 500mV)
~
6.5Y O.2Y
GAIN
Above illustration shows NORMAL gain set-
ting,
Relationship between amplifier gain
and head unit output power
Power _
IMaximum gain I
Equal power - ••• - ~
Head unit volume steps Head uni1 volume steps
Amplifier gain
----_.~ Amplifier gain
(normal) (maximum)
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power,
CD En
section
m( Setting the Unit
)c)
Amplifier gain ... ~ Amplifier gain
(normal) (maximum)
Signal waveform when outputting at
high volume using amplifier gain
control
IMaximum gain I
Signal
waveform
........ Equal power·"
INormal gain
Signal waveform distorted with high output, if
you raise the gain of the amplifier the power
changes only slightly.
C!J
• A cut in sound output may indicate impro-
per setting of the gain control.
To ensure
continuous sound output with the head
unit at ahigh volume, set amplifier gain
control to alevel appropriate
for the preout
maximum output level of the head unit,
so
that volume can remain unchanged and to
control excess output.
•Despite correct volume and gain settings,
the
unit sound still cuts out periodically. In
such cases, please contact the nearest
authorized Pioneer Service Station.
Gain control of this unit
NORMAL
.--~
Preout level: 2 V
(Standard: 500mV)
~
6.5Y O.2Y
GAIN
Above illustration shows NORMAL gain set-
ting,
Relationship between amplifier gain
and head unit output power
Power _
IMaximum gain I
Equal power - ••• - ~
Head unit volume steps Head uni1 volume steps
Amplifier gain
----_.~ Amplifier gain
(normal) (maximum)
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power,
CD En

(,--C_o_n_n_e_ct_i_ng~th_e_un_i_ts_~)
SectIon
C ) CD
Connection diagram
CD Special red battery wire
RD-223 (sold separately)
After completing all other amplifierconnec-
tions, finally connect the battery wire terminal
of the amplifier
to the positive (Ee) battery
terminal.
®Ground wire (Black)
RD-223 (sold separately)
Connect to a
clean, paint-free metal location.
® Car stereo with RCA output jacks (sold sepa-
rately)
@ External output
If only one input plug is used, do not connect
anything to
RCA input jack B.
®Connecting wire with RCA pin plugs (sold se-
parately)
® RCA output jack
([)
RCA input jack A
® RCA input jack B
®Amplifier with RCA input jacks (sold sepa-
rately)
@) Speaker output terminals
Please see the following section for speaker
connection instructions. Refer to Connections
when using the speaker input wire on page 10.
@ Fuse (40 A)
© System remote control wire (sold separately)
Connect male terminal of this wire to the sys-
tem remote control terminal of the car stereo.
The female terminal can be connected to the
auto-antenna
relay control terminal. If the car
stereo lacks a system remote control terminal,
connect the
male terminal to the power term-
inal via the ignition switch.
@ Fuse (30 A) x 2
@Grommet
@Rearside
@
Front side
•Note
INPUT SELEa (input select) switch must be set.
For details. see Setting the Unit on page 5. [!)
Before connecting the
amplifier
AWARNING
• Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap sections
in contact with metal parts in adhesive tape.
• Never cut the insulation of the power supply
to
feed power to other equipment. Current ca-
pacity of the wire is limited.
ACAUTION
• Never shorten any wires. the protection circuit
may malfunction.
•
Never wire the speaker negative cable directly-
to ground.
En CI)
(,--C_o_n_n_e_ct_i_ng~th_e_un_i_ts_~)
SectIon
C ) CD
Connection diagram
CD Special red battery wire
RD-223 (sold separately)
After completing all other amplifierconnec-
tions, finally connect the battery wire terminal
of the amplifier
to the positive (Ee) battery
terminal.
®Ground wire (Black)
RD-223 (sold separately)
Connect to a
clean, paint-free metal location.
® Car stereo with RCA output jacks (sold sepa-
rately)
@ External output
If only one input plug is used, do not connect
anything to
RCA input jack B.
®Connecting wire with RCA pin plugs (sold se-
parately)
® RCA output jack
([)
RCA input jack A
® RCA input jack B
®Amplifier with RCA input jacks (sold sepa-
rately)
@) Speaker output terminals
Please see the following section for speaker
connection instructions. Refer to Connections
when using the speaker input wire on page 10.
@ Fuse (40 A)
© System remote control wire (sold separately)
Connect male terminal of this wire to the sys-
tem remote control terminal of the car stereo.
The female terminal can be connected to the
auto-antenna
relay control terminal. If the car
stereo lacks a system remote control terminal,
connect the
male terminal to the power term-
inal via the ignition switch.
@ Fuse (30 A) x 2
@Grommet
@Rearside
@
Front side
•Note
INPUT SELEa (input select) switch must be set.
For details. see Setting the Unit on page 5. [!)
Before connecting the
amplifier
AWARNING
• Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap sections
in contact with metal parts in adhesive tape.
• Never cut the insulation of the power supply
to
feed power to other equipment. Current ca-
pacity of the wire is limited.
ACAUTION
• Never shorten any wires. the protection circuit
may malfunction.
•
Never wire the speaker negative cable directly-
to ground.
En CI)

section
• ( Connecting the units )c )
About suitable
specification
of speaker
Ensure speakers conform to the following
standards, otherwise there is arisk of fire,
smoke
or damage. Speaker impedance is 2n
to 8 n, or 4nto 8n for two-channel and other
bridge connections.
•Never band together multiple speaker'snega-
tive cables.
•If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch
(12 V DC), the amplifierwill re-
main on with the ignition whether the car
stereo is
on or off, which may exhaust battery
if the engine
is at rest or idling.
•Install and route the separately sold battery
wire
as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away
as possible from the anten-
na, antenna cable and tuner. C!J
About bridged mode
Subwoofer
Four-channel output
Two-channel output
Th ree-channel
Speaker output A
Nominal input:
Min,75W
Nominal input:
Min,200W
Nominal input:
Min,75W
Other than subwoofer
Diagram A- Proper
Pioneer
Amplifier
4Q Bridged Mode
Diagram B- Improper
2Q Bridged Mode
Three-channel
Speaker output B
Four-channel output
Two-channel output
Nominal input:
Min,200W
Max. input:
Min. 150W
Max. input:
Min,400W
Connecting the speakers
The speaker output mode can be four-channel,
three-channel (stereo and
mono) or two-chan-
nel (stereo
or mono), Connect the speaker
leads based on the
mode and the figures
shown below.
Speaker impedance
is max. 4 n, please carefully
check. Improper connection to the amplifiermay
result
in malfunction or personal injury due to
burns from overheating.
For bridged mode for atwo-channel amplifier,
with a
4.n load, either wire two 8.n speakers in
parallel, Left ®and Right 8(Diagram A) or use a
single
4.n speaker, For other amplifiers, please
follow the speaker output connection diagram for
bridging shown
on rear: two 8.n speakers in par-
allel for a
4.n load or asingle 4.n speaker per
channel.
For any further enquiries, contact your local
authorized Pioneer dealer or customer service,
C!J
CD En
Three-channel
Speaker output A
Three-channel
Speaker output B
Max. input:
Min. 150W
Max. input:
Min.400W
section
• ( Connecting the units )c )
About suitable
specification
of speaker
Ensure speakers conform to the following
standards, otherwise there is arisk of fire,
smoke
or damage. Speaker impedance is 2n
to 8 n, or 4nto 8n for two-channel and other
bridge connections.
•Never band together multiple speaker'snega-
tive cables.
•If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch
(12 V DC), the amplifierwill re-
main on with the ignition whether the car
stereo is
on or off, which may exhaust battery
if the engine
is at rest or idling.
•Install and route the separately sold battery
wire
as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away
as possible from the anten-
na, antenna cable and tuner. C!J
About bridged mode
Subwoofer
Four-channel output
Two-channel output
Th ree-channel
Speaker output A
Nominal input:
Min,75W
Nominal input:
Min,200W
Nominal input:
Min,75W
Other than subwoofer
Diagram A- Proper
Pioneer
Amplifier
4Q Bridged Mode
Diagram B- Improper
2Q Bridged Mode
Three-channel
Speaker output B
Four-channel output
Two-channel output
Nominal input:
Min,200W
Max. input:
Min. 150W
Max. input:
Min,400W
Connecting the speakers
The speaker output mode can be four-channel,
three-channel (stereo and
mono) or two-chan-
nel (stereo
or mono), Connect the speaker
leads based on the
mode and the figures
shown below.
Speaker impedance
is max. 4 n, please carefully
check. Improper connection to the amplifiermay
result
in malfunction or personal injury due to
burns from overheating.
For bridged mode for atwo-channel amplifier,
with a
4.n load, either wire two 8.n speakers in
parallel, Left ®and Right 8(Diagram A) or use a
single
4.n speaker, For other amplifiers, please
follow the speaker output connection diagram for
bridging shown
on rear: two 8.n speakers in par-
allel for a
4.n load or asingle 4.n speaker per
channel.
For any further enquiries, contact your local
authorized Pioneer dealer or customer service,
C!J
CD En
Three-channel
Speaker output A
Three-channel
Speaker output B
Max. input:
Min. 150W
Max. input:
Min.400W

( Conneding the units SectIon
) C ).
Four~hannelo~ut
-;;::::::::=ctJ: }
-,!
=n-i~
~~o
=. .II!.&"~ ·1rl:1~1~1~1=---
CD
CD Left
@Right
G) Speaker out A
G) Speaker out B
Three~hannel output
CD Left
@Right
G) Speaker out A
G) Speaker out B (Mono)
1w~hanneloutput(Stereo)
CD Speaker (Left)
@ Speaker (Right)
1wo~hannel output (Mono)
-l-r
~~l
CD Speaker (Mono) (!)
..
m
::::J
CO
-
ii
:r
En CD
( Conneding the units SectIon
) C ).
Four~hannelo~ut
-;;::::::::=ctJ: }
-,!
=n-i~
~~o
=. .II!.&"~ ·1rl:1~1~1~1=---
CD
CD Left
@Right
G) Speaker out A
G) Speaker out B
Three~hannel output
CD Left
@Right
G) Speaker out A
G) Speaker out B (Mono)
1w~hanneloutput(Stereo)
CD Speaker (Left)
@ Speaker (Right)
1wo~hannel output (Mono)
-l-r
~~l
CD Speaker (Mono) (!)
..
m
::::J
CO
-
ii
:r
En CD

SectIon
lED ( Conneding the units )
c'- )
Connedions when using
the RCA input jack
Connect the car stereo RCA output jack and
the RCA
input jack of the amplifier.
•The RCA
output jack of this unit outputs
the signal that comes from The RCA input
jack A.
Four<hanneI/Three<hanneloutput
•Slide INPUT SELECT (input select) switch
to 4CH position.
Connedions when using
the speaker input wire
Connect the car stereo speaker output wires
to the amplifier using the supplied speaker
input wire with RCA pin cord.
<D RCA input jackA
For two-channel output. connect the RCA
plugs to the RCA inputjack A.
®Connecting wire with RCA pin plugs (sold se-
parately)
® From car stereo (RCA output)~
•
CD
<D RCA input jack A
® RCA input jack B
®Connecting wires with RCA plugs (sold sepa-
rately)
@ From car stereo (RCA output)
If only one input plug
is used, e.g. when the
car stereo has only one output
(RCA output),
connect the plug
to RCA input jack Arather
than
B.
lWo<hannel output (Stereo) I(Mono)
•Slide INPUT SELECT (input select) switch
to 2CH position.
<D Car Stereo
®Speaker output
® Red: Right (f)
@Black: Right e
®Black: Left e
®White: Left (f)
(J) Speaker input wire with RCA pin cord
To the RCA input jack of this unit
ill) En
SectIon
lED ( Conneding the units )
c'- )
Connedions when using
the RCA input jack
Connect the car stereo RCA output jack and
the RCA
input jack of the amplifier.
•The RCA
output jack of this unit outputs
the signal that comes from The RCA input
jack A.
Four<hanneI/Three<hanneloutput
•Slide INPUT SELECT (input select) switch
to 4CH position.
Connedions when using
the speaker input wire
Connect the car stereo speaker output wires
to the amplifier using the supplied speaker
input wire with RCA pin cord.
<D RCA input jackA
For two-channel output. connect the RCA
plugs to the RCA inputjack A.
®Connecting wire with RCA pin plugs (sold se-
parately)
® From car stereo (RCA output)~
•
CD
<D RCA input jack A
® RCA input jack B
®Connecting wires with RCA plugs (sold sepa-
rately)
@ From car stereo (RCA output)
If only one input plug
is used, e.g. when the
car stereo has only one output
(RCA output),
connect the plug
to RCA input jack Arather
than
B.
lWo<hannel output (Stereo) I(Mono)
•Slide INPUT SELECT (input select) switch
to 2CH position.
<D Car Stereo
®Speaker output
® Red: Right (f)
@Black: Right e
®Black: Left e
®White: Left (f)
(J) Speaker input wire with RCA pin cord
To the RCA input jack of this unit
ill) En

C_C_o_n_n_ed_i_ng_th_e_u"_i_t_s )
II Note
•If speaker wires with an RCA pin cord from a
headunit
are connected to this amplifier, the
amplifier will automatically turn
on when the
headunit
is turned on. When the headunit is
turned
off, the amplifierturns off automati-
cally. This function
may not work with some
headunits.
In such cases, please use a sys-
tem remote control wire (sold separately). If
multiple amplifiers are to be connected to-
gether synchronously, connect the head unit
and all amplifiers via the system remote con-
trol wire.
•Connect the system remote control wire when
you wish to only turn on the car stereo, not the
amplifier.
•This amplifier automatically selects
an input
signal mode between the
RCA level and the
speaker
level by detecting an input signal. (!)
Conneding the power
terminal
• The use of aspecial red battery and ground
wire RD-223, available separately, is recom-
mended. Connect the battery wire directly
to the
car battery positive terminal (Et» and
the ground wi
re to the car body.
AWARNING
If the battery wire is not securely fixed to the term-
inal using the terminal screws, there
is arisk of
overheating, malfunction
and injury, including
minor burns.
1Route battery wire from engine com-
partment
to the vehicle interior.
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive (Et» battery
terminal.
section
C~ ).
-m
~
ce.
in
::r
CD Positive (Ef») terminal
®Engine compartment
Q) Vehicle interior
CV Fuse (30 A) x2
®Insert the O-ring rubber grommet into the
vehicle
body.
®Drill a 14 mm hole into the vehicle body (1/2
in.) .
2Twist the battery wire, ground wire
and
system remote control wire.
Twist
--.
3Attach lugs to wire ends. Lugs not sup-
plied.
Use pliers, etc., to crimp lugs to wires.
CD Lug
®Battery wire
Q) Ground wire
4Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
En ®
C_C_o_n_n_ed_i_ng_th_e_u"_i_t_s )
II Note
•If speaker wires with an RCA pin cord from a
headunit
are connected to this amplifier, the
amplifier will automatically turn
on when the
headunit
is turned on. When the headunit is
turned
off, the amplifierturns off automati-
cally. This function
may not work with some
headunits.
In such cases, please use a sys-
tem remote control wire (sold separately). If
multiple amplifiers are to be connected to-
gether synchronously, connect the head unit
and all amplifiers via the system remote con-
trol wire.
•Connect the system remote control wire when
you wish to only turn on the car stereo, not the
amplifier.
•This amplifier automatically selects
an input
signal mode between the
RCA level and the
speaker
level by detecting an input signal. (!)
Conneding the power
terminal
• The use of aspecial red battery and ground
wire RD-223, available separately, is recom-
mended. Connect the battery wire directly
to the
car battery positive terminal (Et» and
the ground wi
re to the car body.
AWARNING
If the battery wire is not securely fixed to the term-
inal using the terminal screws, there
is arisk of
overheating, malfunction
and injury, including
minor burns.
1Route battery wire from engine com-
partment
to the vehicle interior.
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive (Et» battery
terminal.
section
C~ ).
-m
~
ce.
in
::r
CD Positive (Ef») terminal
®Engine compartment
Q) Vehicle interior
CV Fuse (30 A) x2
®Insert the O-ring rubber grommet into the
vehicle
body.
®Drill a 14 mm hole into the vehicle body (1/2
in.) .
2Twist the battery wire, ground wire
and
system remote control wire.
Twist
--.
3Attach lugs to wire ends. Lugs not sup-
plied.
Use pliers, etc., to crimp lugs to wires.
CD Lug
®Battery wire
Q) Ground wire
4Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
En ®

Section
• ( Conneding the units
CD System remote control terminal
CV GND terminal
Q) Power terminal
@Terminal screws
®Battery wi re
®Ground wire
(j) System remote control wireC!J
Conneding the speaker
output terminals
1Expose the end of the speaker wires
using nippers oracutter by about 10 mm
(3/8 in.) and twist.
Twist
-------,.t
r--r
10 mm (3/8 inch)
)
(~----~)
CD Lug
CV Speaker wi re
3Connect the speaker wires to the
speaker outputterminals.
Fix the speaker wires securely with the term-
inal screws.
CD Terminal screws
CV Speaker wires
Q) Speaker output terminals0
2Attach lugs to speaker wire ends. Lugs
not supplied.
Use pliers, etc., to crimp lugs to wires.
(ill En
Section
• ( Conneding the units
CD System remote control terminal
CV GND terminal
Q) Power terminal
@Terminal screws
®Battery wi re
®Ground wire
(j) System remote control wireC!J
Conneding the speaker
output terminals
1Expose the end of the speaker wires
using nippers oracutter by about 10 mm
(3/8 in.) and twist.
Twist
-------,.t
r--r
10 mm (3/8 inch)
)
(~----~)
CD Lug
CV Speaker wi re
3Connect the speaker wires to the
speaker outputterminals.
Fix the speaker wires securely with the term-
inal screws.
CD Terminal screws
CV Speaker wires
Q) Speaker output terminals0
2Attach lugs to speaker wire ends. Lugs
not supplied.
Use pliers, etc., to crimp lugs to wires.
(ill En

section
('-- ~) CI
('--I_ns_t_a_lIa_t_io_n ~)
Before installing the amplifier
AWARNING
• Do not use unauthorized parts as this may
cause malfunctions.
•
Do not install this unit where:
-it may interfere with operation of the vehi-
cle.
-it may cause injury to apassenger
as a re-
sult of asudden stop.
•Install tapping screws in such a
way that the
screw tip does not touch any wire. This
is im-
portant to prevent wires from being cut
by vi-
bration of the car, which can result in fire,
•Place all cables away from moving parts, such
as the gear shift and seat rails.
•When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
ACAUTION
• To ensure proper heat dissipation ofthe ampli-
fier, ensure the following during installation:
-Allow adequate space above the amplifier
for proper ventilation.
-
Do not cover the amplifier with afloor mat
orcarpet.
•Place all cables away from hot places, such
as near the heater outlet.
•The optimal installation location differs
de-
pending on the car model. Secure the ampli-
fier at asufficiently rigid location.
•Check all connections and systems before
final installation.
•After installing the amplifier, confirm that the
spare tire, jack and tools can
be easily re-
moved.(!)
Example of installation on
the floor mat or chassis
1 Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm x
18
mm) into the screw holes and push on the
screws with ascrewdriver so they make an im-
print where the installation holes are to be lo-
cated.
2Drill 2.5 mm (1/8 in.) diameter holes at
the imprints either on the carpet or directly
on the
chassis.
3Install the amplifier with the use of
supplied tapping screws (4 mm)( 18 mm).
CD Tapping-screws (4 mm x 18 mm)
®Drill a 2.5 mm (1/8 in.) diameter hole
®Floor mat or chassis (!)
-m
::s
ee.
iii"
::so
En ®
section
('-- ~) CI
('--I_ns_t_a_lIa_t_io_n ~)
Before installing the amplifier
AWARNING
• Do not use unauthorized parts as this may
cause malfunctions.
•
Do not install this unit where:
-it may interfere with operation of the vehi-
cle.
-it may cause injury to apassenger
as a re-
sult of asudden stop.
•Install tapping screws in such a
way that the
screw tip does not touch any wire. This
is im-
portant to prevent wires from being cut
by vi-
bration of the car, which can result in fire.
•Place all cables away from moving parts, such
as the gear shift and seat rails.
•When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
ACAUTION
• To ensure proper heat dissipation ofthe ampli-
fier, ensure the following during installation:
-Allow adequate space above the amplifier
for proper ventilation.
-
Do not cover the amplifier with afloor mat
orcarpet.
•Place all cables away from hot places, such
as near the heater outlet.
•The optimal installation location differs
de-
pending on the car model. Secure the ampli-
fier at asufficiently rigid location.
•Check all connections and systems before
final installation.
•After installing the amplifier, confirm that the
spare tire, jack and tools can
be easily reo
moved.(!)
Example of installation on
the floor mat or chassis
1 Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm x
18
mm) into the screw holes and push on the
screws with ascrewdriver so they make an im-
print where the installation holes are to be lo-
cated.
2Drill 2.5 mm (1/8 in.) diameter holes at
the imprints either on the carpet or directly
on the
chassis.
3Install the amplifier with the use of
supplied tapping screws (4 mm)( 18 mm).
CD Tapping-screws (4 mm x 18 mm)
®Drill a 2.5 mm (1/8 in.) diameter hole
®Floor mat or chassis (!)
-m
::s
ee.
iii"
::so
En ®

Appendix~ _
• ( Additional information)
Specifications
Power source 14.4 VDC (10.8 Vto 15.1 V
allowable)
Grounding system Negative type
Current consumption
25 A(at continuous power,
4U)
Average current drawn ......... 7.9 A (4 U for four channels)
10.5 A (4 Ufor two chan-
nels)
10.7 A (2 Ufor four chan-
nels)
Fuse 40 Ax1
Dimensions
0N xHx D) 245 x 56 x 200 mm
(9-5/8 x2-1/4 x7-7/8 in.)
Weight 2.2
kg (4.9 Ibs)
(Leads
for wiring not in-
cluded)
Maximum power output ....... 150 Wx4 (40) /400 Wx2
(4U)
Continuous power output ... 75 Wx4(at 14.4 V, 4n 20
Hz to 20 kHz, ~ 1%THD)
200 Wx2(at 14.4 V, 4U
BRIDGE, 1kHz, ~ 1% THD)
100 Wx4(at 14.4 V, 2n1
kHz,
~ 1%THD)
Load impedance 4U
(20 to 8Uallowable)
(Bridge connection:
40 to 8
oallowable)
Frequency response
10Hz to 35 kHz (+0 dB. -3
dB)
Signal-to-noise ratio
95 dB (IHF-A network)
Distortion
006 % (10 W, 1kHz)
Separation
67 dB (1 kHz)
60 dB (100 Hz to 10 kHz)
Low pass filter:
Cut off frequency
40 Hz to 500 Hz
Cut off slope
-12 dB/oct
High pass filter:
Cut off frequency
40 Hz to 500 Hz
Cut off slope -12 dB/oct
Gain control:
RCA
200 mV to 6.5 V
Speaker 0.8 Vto
10 V
Maximum input level/impedance:
RCA 6.5 V/ 22 kn
Speaker 10 V /22 kn
® En
(~----~)
CEA2006 Specifications
~t.-r~
:."" i
,.
~.
tEa-I.
Power output 75 WRMS x4Channels (at
14.4
V, 4U and ~ 1%THD
+N)
200 WRMS x2Channels
(at 14.4
V, 40 BRIDGE and
~ 1% THD+N)
100 WRMS x4Channels
(at 14.4
V, 2 0 and ~ 1%
THD+N)
SIN ratio 77 dBA (reference: 1W into
4U)
aNotes
•Specifications and the design are subject to
modifications without notice.
•
The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn
by multiple
power amplifiers.(!)
Appendix~ _
• ( Additional information)
Specifications
Power source 14.4 VDC (10.8 Vto 15.1 V
allowable)
Grounding system Negative type
Current consumption
25 A(at continuous power,
4U)
Average current drawn ......... 7.9 A (4 U for four channels)
10.5 A (4 Ufor two chan-
nels)
10.7 A (2 Ufor four chan-
nels)
Fuse 40 Ax1
Dimensions
0N xHx D) 245 x 56 x 200 mm
(9-5/8 x2-1/4 x7-7/8 in.)
Weight 2.2
kg (4.9 Ibs)
(Leads
for wiring not in-
cluded)
Maximum power output ....... 150 Wx4 (40) /400 Wx2
(4U)
Continuous power output ... 75 Wx4(at 14.4 V, 4n 20
Hz to 20 kHz, ~ 1%THD)
200 Wx2(at 14.4 V, 4U
BRIDGE, 1kHz, ~ 1% THD)
100 Wx4(at 14.4 V, 2n1
kHz,
~ 1%THD)
Load impedance 4U
(20 to 8Uallowable)
(Bridge connection:
40 to 8
oallowable)
Frequency response
10Hz to 35 kHz (+0 dB. -3
dB)
Signal-to-noise ratio
95 dB (IHF-A network)
Distortion
006 % (10 W, 1kHz)
Separation
67 dB (1 kHz)
60 dB (100 Hz to 10 kHz)
Low pass filter:
Cut off frequency
40 Hz to 500 Hz
Cut off slope
-12 dB/oct
High pass filter:
Cut off frequency
40 Hz to 500 Hz
Cut off slope -12 dB/oct
Gain control:
RCA
200 mV to 6.5 V
Speaker 0.8 Vto
10 V
Maximum input level/impedance:
RCA 6.5 V/ 22 kn
Speaker 10 V /22 kn
® En
(~----~)
CEA2006 Specifications
~t.-r~
:."" i
,.
~.
tEa-I.
Power output 75 WRMS x4Channels (at
14.4
V, 4U and ~ 1%THD
+N)
200 WRMS x2Channels
(at 14.4
V, 40 BRIDGE and
~ 1% THD+N)
100 WRMS x4Channels
(at 14.4
V, 2 0 and ~ 1%
THD+N)
SIN ratio 77 dBA (reference: 1W into
4U)
aNotes
•Specifications and the design are subject to
modifications without notice.
•
The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn
by multiple
power amplifiers.(!)

Register your product at
Enregistrez votre produit
au
Registre suproducto en
http://www.pioneerelectronics.com
See "Visit our website" page
Voir fa page "Visitez notre site Web"
Consufte
fa pagina sobre "Visite nuestro sitio Web"
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU
TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: [phone]
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: [phone]
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: [phone]
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: [phone]
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL:
1-877-283-5901
TEL: [phone]
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col. Lomas de Chapultepec, Mexico, D.E 11000
TEL: [phone]
stc.llifS}fillll~ii)
.i}iSJ : ti~t"$J:Pu.J~tH=~i44~13.
• Ili: [phone]
stc •• =f(.5I)fiPll~~
jfji.1Lft~ 7'p*~.jit911!t W ill. J:P ILJ.
9.901-6~
.liS: [phone]
Published by PioneerCorporation.
Copyright©2009 by PioneerCorporation.
All rights reserved.
Publie par Pioneer Corporation. Copyright
© 2009 par Pioneer Corporation. Tous
droits reserves.
<KNAZX> <09100000>
BA0987654321
Printed in China
Imprime en Chine
<YRD5290-A/S> UC
Register your product at
Enregistrez votre produit
au
Registre suproducto en
http://www.pioneerelectronics.com
See "Visit our website" page
Voir fa page "Visitez notre site Web"
Consufte
fa pagina sobre "Visite nuestro sitio Web"
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU
TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: [phone]
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: [phone]
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: [phone]
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: [phone]
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL:
1-877-283-5901
TEL: [phone]
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col. Lomas de Chapultepec, Mexico, D.E 11000
TEL: [phone]
stc.llifS}fillll~ii)
.i}iSJ : ti~t"$J:Pu.J~tH=~i44~13.
• Ili: [phone]
stc •• =f(.5I)fiPll~~
jfji.1Lft~ 7'p*~.jit911!t W ill. J:P ILJ.
9.901-6~
.liS: [phone]
Published by PioneerCorporation.
Copyright©2009 by PioneerCorporation.
All rights reserved.
Publie par Pioneer Corporation. Copyright
© 2009 par Pioneer Corporation. Tous
droits reserves.
<KNAZX> <09100000>
BA0987654321
Printed in China
Imprime en Chine
<YRD5290-A/S> UC

PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONIQUES
DU CANADA, INC.
Main-d'<8uvre
1 an
GARANTIE LIMITEE . . .
GARANTIE VALIDE SEULEMENT DANS LE PAYS OU LE PRODUIT A ETE ACHETE
GARANTIE
Pioneer Electronics (USA) Inc. (PUSA) et Pioneer Electronique du Canada, Inc. (POC) garantissent que les produits distribues par PUSA aux Etats-Unis et par POC au Canada qui, apres
avoir ete installes et utilises conformement au manuel de I'utilisateur inclus avec I'unite, ne fonctionnent pas de
fa~on appropriee dans des conditions d'utilisation normales en raison d'un
vice defabrication. seront repares ou
rem places parune unite devaleur comparable, au choix de PUSAou de POC, sans que vous deviez payerpour les pieces ou les travaux de reparation.
Les unites ou pieces de rechange fournies en vertu de la presente garantie peuvent etre neuves ou remises aneuf. au choix de PUSA ou de
POCo
LA PRESENTE GARANTIE LIMITEE S'APPLIQUE AU PROPRIETAIRE INITIAL AINSI QU'A TOUT PROPRIETAIRE SUBSEQUENT DU PRESENT PRODUIT PIONEER PENDANT LA PERI ODE DE GARANTIE.
A CONDITION QUE LE PRODUIT AIT ETE ACHETE CHEZ UN DISTRIBUTEUR OU MARCHAND PIONEER AUTORISE AUX ETATS·UNIS OU AU CANADA. VOUS DEVREZ FOURNIR UN RELEVE DE CAISSE
OU UNE AUTRE PREUVE D'ACHAT VALl DE INDIQUANT LA DATE DE L'ACHAT INITIAL OU, SI VOUS LOUEZ LE PRODUIT, VOTRE CONTRAT DE LOCATION INDIQUANT L'ENDROIT ET LA DATE DE
LA PREMIERE LOCATION. SI JAMAIS UN SERVICE DE REPARATION EST REQUIS, LE PRODUIT DOlT ETRE EXPEDIE PENDANT LA PERIODE DE GARANTIE, EN PORT PREPAYE, A L'INTERIEUR DU
PAYS OU L'ACHAT A ETE EFFECTUE SEULEMENT, TEL QU'IL EST EXPLIQUE DANS LE PRESENT DOCUMENT. VOUS eTES RESPONSABLE DU DEMONTAGE ET DE L'INSTALLATION DU PRODUIT.
PUSA OU POC, LE CAS ECHEANT, PAIERA POUR VOUS RETOURNER LE PRODUIT REPARE OU REMPLACE, A L'INTERIEUR DU PAYS OU L'ACHAT A ETE EFFECTuE.
PERIODE DE GARANTIE DES PRODUITS Pieces
Produits stereo pour I'auto 1 an
La periode de garantie pour lesclients qui louent Ie produil commence Ie jour ou Ie produil est utilise pour la premiere fois (a) pendant la periode de location ou (b) apres la vente au detail, selon ce qui se produit en premier.
ELEMENTS NON COUVERTS PAR LA GARANTIE
UN PRODUIT ACHETE CHEZ UN DISTRIBUTEUR NON AUTORISE N'EST COUVERT PAR AUCUNE GARANTIE EXPRESSE OU IMPLICITE, YCOMPRIS QUELQUE GARANTIE
IMPLICITE
DE QUALITE MARCHANDE OU D'ADAPTATION it. UN USAGE PARTICULIER QUE CE SO IT. DE PLUS. CE PRODUIT EST STRICTEMENT VENDU "TEL QUEL " ET
"AVEC TOUS SES DEFAUTS EVENTUELS ".
PIONEER N'EST PAS RESPONSABLE
DE QUELQUE DOMMAGE CONSECUTIF ET(OU) INDIRECT QUE CE SOIT.
PIONEER
NE GARANTIT PAS LES PRODUITS ENUMERES CI-DESSUS LORSQU'ILS SONT UTILISES ADES FINS COMMERCIALES OU PROFESSIONNELLES, OU AU SEIN
DE TOUTE APPLICATION INDUSTRIELLE OU COMMERCIALE QUE CE SOIT.
LA PRESENTE GARANTIE
NE S'APPLIQUE PAS SI LE PRODUIT AETE SOUMIS it. UNE PUISSANCE NOMINALE EXCEDANT CELLE QUI A ETE ETABLIE DANS LES
DOCUMENTS S'Y APPLIQUANT.
LA PRESENTE GARANTIE NE COUVRE PAS LES TELEVISEURS OU LES ECRANS ENDOMMAGES EN RAISON DE L'APPLICATION D'IMAGES STATIQUES ET IMMOBILES
PENDANT
DE LONGUES PERIODES (IMAGES REMANENTES).
LA PRESENTE GARANTIE
NE COUVRE PAS LE COFFRAGE OU LES ELEMENTS ESTHETIQUES, LES ANTENNES INSTALLEES PAR L'UTILISATEUR. LES DOMMAGES AUX
DISQUES OU AUX RUBANS OU DISQUES D'ENREGISTREMENT, LES DOMMAGES AU PRODUIT DECOULANT D'UNE RETOUCHE, D'UNE MODIFICATION NON AUTORISEE
PAR ECRIT PAR PIONEER, D'UN ACCIDENT, D'UN USAGE INAPPROPRIE
OU D'UN USAGE ABUSIF. LES DOMMAGES PRODUITS PAR LA FOUDRE OU LA SURTENSION,
LES DOMMAGES SUBSEQUENTS DECOULANT
DE FUITES, LES DOMMAGES DECOULANT DE PILES DEFECTUEUSES OU DE L'UTILISATION DE PILES NON
CONFORMES it. CELLES QUI SONT SPECIFIEES DANS LE MANUEL DE L'UTILISATEUR.
LA PRESENTE GARANTIE
NE COUVRE PAS LE COOT DES PIECES OU DE LA MAIN·D'lEUVRE QUI SERAIENT AUTREMENT OFFERTES SANS FRAIS EN VERTU DE LA
PRESENTE GARANTIE.
SI ELLES SONT OBTENUES AUPRES D'UNE SOURCE AUTRE QU'UNE SOCIETE DE SERVICE OU AUTRE AUTORISEE OU DESIGNEE PAR
PIONEER. LA PRESENTE GARANTIE
NE COUVRE PAS LES DEFECTUOSITES OU LES DOMMAGES CAUSES PAR L'UTILISATION D'UNE MAIN·D'lEUVRE OU DE PIECES
NON AUTORISEES, NI D'UN ENTRETIEN INADEQUAT.
LES NUMEROS
DE SERlE MODIFIES. OBLITERES OU ENLEVES ANNULENT LA PRESENTE GARANTIE DANS SA TOTALITE.
INVALIDITE DE TOUTE AUTRE GARANTIE
AUX ETATS·UNIS -PIONEER LIMITE SES OBLIGATIONS EN VERTU DE TOUTE GARANTIE IMPLICITE QUE CE SOIT, YCOMPRIS ENTRE AUTRES LES GARANTIES IMPLICITES
DE QUALITE MARCHANDE OU D'ADAPTATION it. UN USAGE PARTICULlER, it. UNE PERIODE N'EXCEDANT PAS LA PERIODE DE GARANTIE. AUCUNE GARANTIE NE S'APPLIQUE
APRES LA PERIODE
DE GARANTIE. CERTAINS ETATS NE PERMETIENT PAS LA LIMITATION DE LA DUREE D'UNE GARANTIE IMPLICITE, ET CERTAINS NE PERMETTENT PAS
L'EXCLUS10NOO
LA LIMITATION DES DOMM-AGES GONSEw'l'IFS-~u.:CHl~TS-A.ES- L-lWMTIONS .£TEXCl.US'ONS El'ABLISS Cl·OESSUS P6U¥5f\1T-OO!I!C ~JS PAS
S'APPLIQUER
it. VOUS. LA PRESENTE GARANTIE VOUS DONNE DES DROITS LEGAUX SPECIFIQUES. VOUS POUVEZ JOUIR D'AUTRES DROITS, QUI PEUVENT VARIER D'UN
ETAT A L'AUTRE.
AU CANADA -SOUS RESERVE DE CE QUI EST EXPRESSEMENT STIPULE DANS LES PRESENTES, AUCUNE REPRESENTATION, GARANTIE, OBLIGATION OU CONDITION,
QU'ELLE SOIT IMPLICITE. OBLIGATOIRE
OU AUTRE. NE S'APPLIQUE it. CE PRODUIT.
SERVICE
Pour profiter du service en vertu de la garantie aux Etats-Unis et au Canada, vous devez presenter votre reieve de caisse ou, si vous louez Ie produit, votre contrat de location
indiquant I'endroit et la date de la transaction
par Ie premier proprietaire.
AUX ETATS-UNIS -Communiquez avec un des partenaires Pioneer suivants pour Ie service:
Votre marchand Pioneer autorise -Votre marchand Pioneer peut reparer ou remplacer votre unite, ou bien vous diriger vers une societe de service Pioneer autorisee. Votre re.;u
de caisse devrait enumerer ses coordonnees (numeros de telephone et de telecopieur, courriel, etc.).
Votre societe de service autorisee •Celle-ci peut reparer la plupart des produits electroniques pour "auto et vous aviser des options supplementaires qui pourraient s·appliquer.
Veuillez acceder au site Web de Pioneer awww.pioneerelectronics.com.c1iquer sur I'onglet "Service and
Support" et choisir "Authorized Service Locator" pour trouver la societe
de service Pioneer la plus proche.
Pioneer Electronics Service -Ce service peut vous aviserdesoptions de service optimales pourvotre modele et votre emplacement geographique. Veuillez consulter les coordonnees
ci-dessous pour communiquer avec Pioneer par telephone, par courrier ou par
Ie biais de son site Web.
AU
CANADA -POC adesigne un certain nombre de societes de service autorisees partout au Canada si jamais vous avez besoin de services de reparation pour votre produit.
Communiquez avec Pioneer Electronique du Canada (Ies coordonnees se trouvent ci-dessous) pour trouver une societe de service autorisee.
Expedition de votre unite aux fins de service - Si vous expediez I'unite, vous devez I'emballer soigneusement et I'envoyer aune societe de service autorisee ou aPioneer,
en port prepaye et selon une methode de transport pouvant etre suivie
et assuree. Emballez Ie produit au moyen de materiaux coussines adequats pour eviter les dommages
pendant
Ie transport. Incluez votre nom, votre adresse et un numero de telephone ou nous pouvons vous joindre pendant les heures de bureau.
Pour toutes les plaintes et problemes aux Etats-Unis, communiquez avec
Ie service de Soutien ala clientele au 1-800-421-1404. Au Canada, communiquez avec Ie groupe de
Satisfaction de la clientele au 1-877-283-5901.
Pour
Ie raccordement ou Ie fonctionnement de votre unite, ou pour trouver une societe de service autorisee, appelez ou ecrivez a:
AUX ETATS-UNIS AU CANADA
PIONEER ELECTRONICS SERVICE, INC. GROUPE DE SATISFACTION DE LA CLIENTELE
P.O. BOX 1760 PIONEER ELECTRONIQUES DU CANADA, INC.
LONG BEACH CALIFORNIA 90801 300 ALLSTATE PARKWAY
1-800-421-1404 MARKHAM, ON L3R
OP2
[phone]
http://www.pioneerelectronics.com1-877-283-5901
http://www.pioneerelectronics.ca
REGLEMENT DES CONFLITS
AUX ETATS-UNIS -SI un canflit se produit entre vous et Pioneer apres la n!ponse it une demande initiale faite au service de Soutien it la clientele, vous pouvez avoir
recours au Programme de resolution des plaintes de Pioneer pour resoudre Ie conflit. Ce programme vous est offert sans frais. Vous devez avoir recours au Programme
de
resolution des plaintes avant de vous prevaloir de vos droits ou de chercher reparation en vertu du Titre Ide la loi Magnuson-Moss Warranty-Federal Trade Commission
Improvement Act, 15 U.S.C. 2301 et S.S.
Pour avoir recours au Programme de resolution des plaintes, appelez au 1800 421-1404 et expliquez au representant du service it la clientele qui vous repondra Ie
probleme auquel vous faites face et les demarches que vous avez entreprises pour faire reparer Ie produit pendant la periode de garantie. puis don nez-lui Ie nom du
distributeur / marchand autorise aupres duquel vous vous etes procure Ie produit Pioneer. Une fois que votre plainte aete expliquee au representant, un numero de
resolution vous sera communique. Pioneer etudiera Ie conflit et, dans un delai de quarante (40) jours apres la reception de votre plainte, (1) repondra it votre plalnte
par ecrit pour vous aviser des demarches qu'elle entreprendra pour resoudre Ie con flit, et indiquera combien de temps ces demarches prendront ;ou (2) repondra
a votre plainte par ecrit pour vous indiquer les raisons pour lesquelles elle n'entreprendra aucune demarche,
AU CANADA· Communiquez avec Ie directeur de la Satisfaction de la clientele au (905) 946·7446 pour discuter de votre plainte et resoudre rapidement Ie probleme,
ENREGISTREZLE LIEU ET LA DATE D'ACHATPOUR REFERENCE ULTERIEURE
NO. dumodele: NO.deserie :, _
Date d'achat: Achete
de: ~
PRENEZSOIN DE GARDERCEITE INFORMATlO'.J ETVOTRE REGU D'Aa-lATDANSUN ENDROlTSUR
<CRY1276-A/U >
Imprime en Chine
PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONIQUES
DU CANADA, INC.
Main-d'<8uvre
1 an
GARANTIE LIMITEE . . .
GARANTIE VALIDE SEULEMENT DANS LE PAYS OU LE PRODUIT A ETE ACHETE
GARANTIE
Pioneer Electronics (USA) Inc. (PUSA) et Pioneer Electronique du Canada, Inc. (POC) garantissent que les produits distribues par PUSA aux Etats-Unis et par POC au Canada qui, apres
avoir ete installes et utilises conformement au manuel de I'utilisateur inclus avec I'unite, ne fonctionnent pas de
fa~on appropriee dans des conditions d'utilisation normales en raison d'un
vice defabrication. seront repares ou
rem places parune unite devaleur comparable, au choix de PUSAou de POC, sans que vous deviez payerpour les pieces ou les travaux de reparation.
Les unites ou pieces de rechange fournies en vertu de la presente garantie peuvent etre neuves ou remises aneuf. au choix de PUSA ou de
POCo
LA PRESENTE GARANTIE LIMITEE S'APPLIQUE AU PROPRIETAIRE INITIAL AINSI QU'A TOUT PROPRIETAIRE SUBSEQUENT DU PRESENT PRODUIT PIONEER PENDANT LA PERI ODE DE GARANTIE.
A CONDITION QUE LE PRODUIT AIT ETE ACHETE CHEZ UN DISTRIBUTEUR OU MARCHAND PIONEER AUTORISE AUX ETATS·UNIS OU AU CANADA. VOUS DEVREZ FOURNIR UN RELEVE DE CAISSE
OU UNE AUTRE PREUVE D'ACHAT VALl DE INDIQUANT LA DATE DE L'ACHAT INITIAL OU, SI VOUS LOUEZ LE PRODUIT, VOTRE CONTRAT DE LOCATION INDIQUANT L'ENDROIT ET LA DATE DE
LA PREMIERE LOCATION. SI JAMAIS UN SERVICE DE REPARATION EST REQUIS, LE PRODUIT DOlT ETRE EXPEDIE PENDANT LA PERIODE DE GARANTIE, EN PORT PREPAYE, A L'INTERIEUR DU
PAYS OU L'ACHAT A ETE EFFECTUE SEULEMENT, TEL QU'IL EST EXPLIQUE DANS LE PRESENT DOCUMENT. VOUS eTES RESPONSABLE DU DEMONTAGE ET DE L'INSTALLATION DU PRODUIT.
PUSA OU POC, LE CAS ECHEANT, PAIERA POUR VOUS RETOURNER LE PRODUIT REPARE OU REMPLACE, A L'INTERIEUR DU PAYS OU L'ACHAT A ETE EFFECTuE.
PERIODE DE GARANTIE DES PRODUITS Pieces
Produits stereo pour I'auto 1 an
La periode de garantie pour lesclients qui louent Ie produil commence Ie jour ou Ie produil est utilise pour la premiere fois (a) pendant la periode de location ou (b) apres la vente au detail, selon ce qui se produit en premier.
ELEMENTS NON COUVERTS PAR LA GARANTIE
UN PRODUIT ACHETE CHEZ UN DISTRIBUTEUR NON AUTORISE N'EST COUVERT PAR AUCUNE GARANTIE EXPRESSE OU IMPLICITE, YCOMPRIS QUELQUE GARANTIE
IMPLICITE
DE QUALITE MARCHANDE OU D'ADAPTATION it. UN USAGE PARTICULIER QUE CE SO IT. DE PLUS. CE PRODUIT EST STRICTEMENT VENDU "TEL QUEL " ET
"AVEC TOUS SES DEFAUTS EVENTUELS ".
PIONEER N'EST PAS RESPONSABLE
DE QUELQUE DOMMAGE CONSECUTIF ET(OU) INDIRECT QUE CE SOIT.
PIONEER
NE GARANTIT PAS LES PRODUITS ENUMERES CI-DESSUS LORSQU'ILS SONT UTILISES ADES FINS COMMERCIALES OU PROFESSIONNELLES, OU AU SEIN
DE TOUTE APPLICATION INDUSTRIELLE OU COMMERCIALE QUE CE SOIT.
LA PRESENTE GARANTIE
NE S'APPLIQUE PAS SI LE PRODUIT AETE SOUMIS it. UNE PUISSANCE NOMINALE EXCEDANT CELLE QUI A ETE ETABLIE DANS LES
DOCUMENTS S'Y APPLIQUANT.
LA PRESENTE GARANTIE NE COUVRE PAS LES TELEVISEURS OU LES ECRANS ENDOMMAGES EN RAISON DE L'APPLICATION D'IMAGES STATIQUES ET IMMOBILES
PENDANT
DE LONGUES PERIODES (IMAGES REMANENTES).
LA PRESENTE GARANTIE
NE COUVRE PAS LE COFFRAGE OU LES ELEMENTS ESTHETIQUES, LES ANTENNES INSTALLEES PAR L'UTILISATEUR. LES DOMMAGES AUX
DISQUES OU AUX RUBANS OU DISQUES D'ENREGISTREMENT, LES DOMMAGES AU PRODUIT DECOULANT D'UNE RETOUCHE, D'UNE MODIFICATION NON AUTORISEE
PAR ECRIT PAR PIONEER, D'UN ACCIDENT, D'UN USAGE INAPPROPRIE
OU D'UN USAGE ABUSIF. LES DOMMAGES PRODUITS PAR LA FOUDRE OU LA SURTENSION,
LES DOMMAGES SUBSEQUENTS DECOULANT
DE FUITES, LES DOMMAGES DECOULANT DE PILES DEFECTUEUSES OU DE L'UTILISATION DE PILES NON
CONFORMES it. CELLES QUI SONT SPECIFIEES DANS LE MANUEL DE L'UTILISATEUR.
LA PRESENTE GARANTIE
NE COUVRE PAS LE COOT DES PIECES OU DE LA MAIN·D'lEUVRE QUI SERAIENT AUTREMENT OFFERTES SANS FRAIS EN VERTU DE LA
PRESENTE GARANTIE.
SI ELLES SONT OBTENUES AUPRES D'UNE SOURCE AUTRE QU'UNE SOCIETE DE SERVICE OU AUTRE AUTORISEE OU DESIGNEE PAR
PIONEER. LA PRESENTE GARANTIE
NE COUVRE PAS LES DEFECTUOSITES OU LES DOMMAGES CAUSES PAR L'UTILISATION D'UNE MAIN·D'lEUVRE OU DE PIECES
NON AUTORISEES, NI D'UN ENTRETIEN INADEQUAT.
LES NUMEROS
DE SERlE MODIFIES. OBLITERES OU ENLEVES ANNULENT LA PRESENTE GARANTIE DANS SA TOTALITE.
INVALIDITE DE TOUTE AUTRE GARANTIE
AUX ETATS·UNIS -PIONEER LIMITE SES OBLIGATIONS EN VERTU DE TOUTE GARANTIE IMPLICITE QUE CE SOIT, YCOMPRIS ENTRE AUTRES LES GARANTIES IMPLICITES
DE QUALITE MARCHANDE OU D'ADAPTATION it. UN USAGE PARTICULlER, it. UNE PERIODE N'EXCEDANT PAS LA PERIODE DE GARANTIE. AUCUNE GARANTIE NE S'APPLIQUE
APRES LA PERIODE
DE GARANTIE. CERTAINS ETATS NE PERMETIENT PAS LA LIMITATION DE LA DUREE D'UNE GARANTIE IMPLICITE, ET CERTAINS NE PERMETTENT PAS
L'EXCLUS10NOO
LA LIMITATION DES DOMM-AGES GONSEw'l'IFS-~u.:CHl~TS-A.ES- L-lWMTIONS .£TEXCl.US'ONS El'ABLISS Cl·OESSUS P6U¥5f\1T-OO!I!C ~JS PAS
S'APPLIQUER
it. VOUS. LA PRESENTE GARANTIE VOUS DONNE DES DROITS LEGAUX SPECIFIQUES. VOUS POUVEZ JOUIR D'AUTRES DROITS, QUI PEUVENT VARIER D'UN
ETAT A L'AUTRE.
AU CANADA -SOUS RESERVE DE CE QUI EST EXPRESSEMENT STIPULE DANS LES PRESENTES, AUCUNE REPRESENTATION, GARANTIE, OBLIGATION OU CONDITION,
QU'ELLE SOIT IMPLICITE. OBLIGATOIRE
OU AUTRE. NE S'APPLIQUE it. CE PRODUIT.
SERVICE
Pour profiter du service en vertu de la garantie aux Etats-Unis et au Canada, vous devez presenter votre reieve de caisse ou, si vous louez Ie produit, votre contrat de location
indiquant I'endroit et la date de la transaction
par Ie premier proprietaire.
AUX ETATS-UNIS -Communiquez avec un des partenaires Pioneer suivants pour Ie service:
Votre marchand Pioneer autorise -Votre marchand Pioneer peut reparer ou remplacer votre unite, ou bien vous diriger vers une societe de service Pioneer autorisee. Votre re.;u
de caisse devrait enumerer ses coordonnees (numeros de telephone et de telecopieur, courriel, etc.).
Votre societe de service autorisee •Celle-ci peut reparer la plupart des produits electroniques pour "auto et vous aviser des options supplementaires qui pourraient s·appliquer.
Veuillez acceder au site Web de Pioneer awww.pioneerelectronics.com.c1iquer sur I'onglet "Service and
Support" et choisir "Authorized Service Locator" pour trouver la societe
de service Pioneer la plus proche.
Pioneer Electronics Service -Ce service peut vous aviserdesoptions de service optimales pourvotre modele et votre emplacement geographique. Veuillez consulter les coordonnees
ci-dessous pour communiquer avec Pioneer par telephone, par courrier ou par
Ie biais de son site Web.
AU
CANADA -POC adesigne un certain nombre de societes de service autorisees partout au Canada si jamais vous avez besoin de services de reparation pour votre produit.
Communiquez avec Pioneer Electronique du Canada (Ies coordonnees se trouvent ci-dessous) pour trouver une societe de service autorisee.
Expedition de votre unite aux fins de service - Si vous expediez I'unite, vous devez I'emballer soigneusement et I'envoyer aune societe de service autorisee ou aPioneer,
en port prepaye et selon une methode de transport pouvant etre suivie
et assuree. Emballez Ie produit au moyen de materiaux coussines adequats pour eviter les dommages
pendant
Ie transport. Incluez votre nom, votre adresse et un numero de telephone ou nous pouvons vous joindre pendant les heures de bureau.
Pour toutes les plaintes et problemes aux Etats-Unis, communiquez avec
Ie service de Soutien ala clientele au 1-800-421-1404. Au Canada, communiquez avec Ie groupe de
Satisfaction de la clientele au 1-877-283-5901.
Pour
Ie raccordement ou Ie fonctionnement de votre unite, ou pour trouver une societe de service autorisee, appelez ou ecrivez a:
AUX ETATS-UNIS AU CANADA
PIONEER ELECTRONICS SERVICE, INC. GROUPE DE SATISFACTION DE LA CLIENTELE
P.O. BOX 1760 PIONEER ELECTRONIQUES DU CANADA, INC.
LONG BEACH CALIFORNIA 90801 300 ALLSTATE PARKWAY
1-800-421-1404 MARKHAM, ON L3R
OP2
[phone]
http://www.pioneerelectronics.com1-877-283-5901
http://www.pioneerelectronics.ca
REGLEMENT DES CONFLITS
AUX ETATS-UNIS -SI un canflit se produit entre vous et Pioneer apres la n!ponse it une demande initiale faite au service de Soutien it la clientele, vous pouvez avoir
recours au Programme de resolution des plaintes de Pioneer pour resoudre Ie conflit. Ce programme vous est offert sans frais. Vous devez avoir recours au Programme
de
resolution des plaintes avant de vous prevaloir de vos droits ou de chercher reparation en vertu du Titre Ide la loi Magnuson-Moss Warranty-Federal Trade Commission
Improvement Act, 15 U.S.C. 2301 et S.S.
Pour avoir recours au Programme de resolution des plaintes, appelez au 1800 421-1404 et expliquez au representant du service it la clientele qui vous repondra Ie
probleme auquel vous faites face et les demarches que vous avez entreprises pour faire reparer Ie produit pendant la periode de garantie. puis don nez-lui Ie nom du
distributeur / marchand autorise aupres duquel vous vous etes procure Ie produit Pioneer. Une fois que votre plainte aete expliquee au representant, un numero de
resolution vous sera communique. Pioneer etudiera Ie conflit et, dans un delai de quarante (40) jours apres la reception de votre plainte, (1) repondra it votre plalnte
par ecrit pour vous aviser des demarches qu'elle entreprendra pour resoudre Ie con flit, et indiquera combien de temps ces demarches prendront ;ou (2) repondra
a votre plainte par ecrit pour vous indiquer les raisons pour lesquelles elle n'entreprendra aucune demarche,
AU CANADA· Communiquez avec Ie directeur de la Satisfaction de la clientele au (905) 946·7446 pour discuter de votre plainte et resoudre rapidement Ie probleme,
ENREGISTREZLE LIEU ET LA DATE D'ACHATPOUR REFERENCE ULTERIEURE
NO. dumodele: NO.deserie :, _
Date d'achat: Achete
de: ~
PRENEZSOIN DE GARDERCEITE INFORMATlO'.J ETVOTRE REGU D'Aa-lATDANSUN ENDROlTSUR
<CRY1276-A/U >
Imprime en Chine

PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONICS
OF CANADA, INC.
LIMITED WARRANTY
WARRANTY VALID ONLY IN COUNTRY OF PRODUCT PURCHASE
WARRANTY
Pioneer Electronics (USA) Inc. (PUSA), and Pioneer Electronics Of canada, Inc. (POC), warrant that products distributed by PUSA in the U.S.A., and by POC in canada that fail to
function properly under nonnal use due to amanufacturing defect when installed and operated according to the owner's manual endosed with the unit will
be repaired or replaced with a
unit of comparable value, at the option
of PUSA or POC, without charge to you for parts or actual repair work. Replacement units and/or parts supplied underthis warranty may be
new or rebui~ at the option of PUSA or POCo
THISLIMITEDWARRANTYAPPLIESTOTHEORIGINALOR ANYSUBSEQUENTOWNER OFTHIS PIONEER PRODUCTDURINGTHEWARRANTYPERIODPROVIDEDTHE
PRODUCT
WAS PURCHASEDFROM AN AUTHORIZED PIONEER DISTRIBUTOR/DEALER IN THE U.S.A.OR CANADA. YOU WILL BE REQUIREDTO PROVIDE A SALES
RECEIPTOROTHERVALIDPROOFOFPURCHASESHOWING THEDATE OF ORIGINALPURCHASEOR, IFRENTED, YOUR RENTALCONTRACTSHOWINGTHEPLACE
ANDDATEOFFIRST
RENTAL INTHEEVENTSERVICEISREQUIRED,THEPRODUCTMUSTBEDELIVEREDWITHINTHEWARRANTYPERIOD,TRANSPORTATIONPREPAID,
ONLY FROM WITHIN
THE COUNTRY OF PURCHASE AS EXPLAINEDINTHIS DOCUMENT. YOU WILL BE RESPONSIBLEFOR REMOVAL AND INSTALLATION OF THE
PRODUCT. PUSAOR POC, AS APPROPRIATE,
WILL PAY TO RETURN THE REPAIREDOR REPLACEMENTPRODUCTTO YOU WITHINTHECOUNTRYOF PURCHASE.
PRODUCTWARRANTVPERIOD f4m ld.b2r
Car Stereo Products 1 Year 1 Year
The warranty perlod for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IFTHISPRODUCTWASPURCHASEDFROMANUNAUTHORIZEDDISTRIBUTOR, THEREARENOWARRANTIES, EXPRESSORIMPLIED,INCLUDINGTHE IMPLIEDWARRANTY
OFMERCHANTABILITYANDTHEIMPLIEDWARRANTY
OF FITNESS FORA PARTICULARPURPOSEANDTHIS PRODUCTISSOLDSTRICTLY "AS IS"AND"WITH ALL FAULTS".
PIONEERSHALLNOTBELIABLEFORANYCONSEQUENTIALANDIORINCIDENTALDAMAGES.
PIONEER DOESNOTWARRANTANY PRODUCTLISTEDABOVEWHEN IT
IS USED IN ATRADEOR BUSINESS OR IN ANYINDUSTRIAL OR COMMERCIALAPPLICATION.
THISWARRANTYDOESNOTAPPLYIFTHEPRODUCTHAS BEENSUBJECTEDTO POWER
IN EXCESSOFITSPUBLISHEDPOWER RATlNG.
THIS WARRANTYDOESNOTCOVER DISPLAYSCREENSDAMAGEDBYSTATIC,NON-MOVING,IMAGESAPPLIED FOR LENGTHY PERIODS(BURN-IN).
THISWARRANTYDOESNOTCOVERTHECABINETORANYAPPEARANCErTEM,USERATTACHEDANTENNA,ANYDAMAGETORECORDSORRECORDlNGTAPESORDISCS,ANY
DAMAGETOTHEPRODUCTRESULTlNGFROM
AL TERATlONS,MOOIFlCATlONSNOTAUTHORIZED IN WRITINGBYPIONEER,ACClDENT,MISUSE OR ABUSE, DAMAGEDUETO
UGtmlNGORTOPOWERSURGES,SUBSEQUENTDAMAGEFROMLEAKING,DAMAGEFROMN>PERATlVEBATTERIES,ORTHEUSEOFBATTERlESNOTCONFOR~TOTHOSE
SPECIAEDINTHEOWNER'SMANUAL
THISWARRANTYDOESNOTCOVERTHECOST
OF PARTS OR LABORWHICHWOULDBEOTHERWISEPROVIDEDWITHOUTCHARGEUNDERTHISWARRANTY OBTAfED FROM
ANYSOURCEOTHERTHANAPIONEERAUTHORIZEDSERVJCEcotIPANYOROTHERDESlGNATEDLOCATION.THISWARRANTYDOESNOTCOVERDEFECTSORDAMAGECAUSED
BYTHEUSEOFUNAUTHORIZEDPARTSORLABORORFROMIMPROPERMAINTENANCE.
ALTERED,DEFACED,ORREMOVEDSERIALNUMBERSVOID
THIS ENTIREWARRANTY
NOOTHERWARRANTIES
IN THE U.S.A. -PIONEER LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITYANDFITNESSFORAPARTlCULARPURPOSE, TO APERIODNOTTOEXCEEDTHEWARRANTYPERIOD. NOWARRANTlESSHALLAPPLY AFTERTHE
WARRANTYPERIOD. SOMESTATESDONOT
ALLOW LIMITATIONSON HOWLONGANIMPLIEDWARRANTYLASTSANDSOMESTATESDONOTALLOWTHEEXCLUSIONS
OR LIMITATIONSOFINCIDENTALOR CONSEQUENTIALDAMAGES, SOTHEABOVE LIMITATIONS OREXCLUSIONS
MAY NOT APPL YTO YOU. THIS WARRANTYGIVES
YOU SPECIFIC
LEGAL RIGHTS ANDYOU MAY HAVEOTHER RIGHTS WHICH MAY VARYFROM STATE TO STATE.
IN
CANADA· EXCEPT AS EXPRESSLYPROVIDEDHEREIN,THEREARENOREPRESENTATIONS,WARRANTIES,OBLIGATIONS OR CONDITIONS,IMPLIED,STATUTORY
OR OTHERWISE,APPLICABLETOTHIS PRODUCT.
TO OBTAIN SERVICE
In the U.S.A. or Canada to receive warranty service you need to present your sales receipt or your rental contract showing place and date of original owner's transaction.
Y.SA - Please contact one of the following Pioneer partners to obtain service:
Your Authorized Pioneer Dealer - Your Pioneer Dealer may repair or replace your unit, or refer you to an Authorized Pioneer Service Company. Your sales receipt should
list the contact information (phone number, fax, email, etc.)
for your Dealer.
Your Authorized Pioneer Service Company -Can perform repairs for most Car Electronics products and can advise
other options as applicable. Please access the
Pioneer website at
www.pioneerelectronlcs.com and click on Service and Support and select Authorized Service Locator to find the nearest Pioneer servicer.
Pioneer Electronics Service -Can advise the optimal service option
for your model and geographic location. Please reference the information listed below and phone,
email or access the Pioneer website to contact Pioneer.
~ -POC has anumber of Authorized Service Companies should your product require service. Contact Pioneer of Canada as listed below to obtain alocal service location.
Shipping Your Unit for Service· Please package it carefull'( and send it, transportation prepaid by atraceable, insured method, to an Authorized Service Company or Pioneer.
Use adequate padding material to prevent damage in
transi. Include your name, address and telephone number where you can be reached during business hours.
On all complaints and concerns in the U.S.A. call Customer Support at 1-800-421-1404, or, in Canada, call Customer Satisfaction at 1-877-283-5901.
IN THE U.S.A. IN CANADA
For hook-up and ~peration of your unit or to locat~ an For additional information on this warranty, please call or write:
AuthOrized Service Company, please call or write: CUSTOMERSATISFACTIONGROUP
PIONEER ELECTRONICS SERVICE, INC. PIONEER ELECTRONICS OF CANADA INC
P.O. BOX 1760 300 ALLSTATE PARKWAY' .
LONG BEACH, CALIFORNIA 90801 MARKHAM ON L3R OP2
1-800-421-1404 [phone]' 1-877-283-5901
http://www . pioneerelectronics.com http://www.pioneerelectronics.ca
DISPUTERESOLUTION
IN THE U.S.A .• Following our response to any initial request to Customer Support, should adispute arise between you and Pioneer, Pioneer makes available its Complaint
Resolution Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program
before you exercise any rights under, or seek any remedies, created
by Title Iof the Magnuson-Moss Warranty-Federal Trade ConYnission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-421-1404 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer product was purchased. After the complaint
has been explained to the representative, aresolution number will be issued. Within
40 days of receiving your complaint, Pioneer will investigate the dispute and will either:
(1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing
informing you
why it will not take any action.
IN
CANADA -Call the Customer Satisfaction Manager at [phone] to discuss your complaint and to obtain aprompt resolution.
RECORDTHE PLACEAND DATEOFPURCHASE FOR FUTUREREFERENCE
Model No. Serial No. Purchase Date _
Purchased From KEEP THIS INFORMATION AND YOUR SALES RECEIPT
IN ASAFE PLACE <
CRY1276-A/U >
Printed in China
PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONICS
OF CANADA, INC.
LIMITED WARRANTY
WARRANTY VALID ONLY IN COUNTRY OF PRODUCT PURCHASE
WARRANTY
Pioneer Electronics (USA) Inc. (PUSA), and Pioneer Electronics Of canada, Inc. (POC), warrant that products distributed by PUSA in the U.S.A., and by POC in canada that fail to
function properly under nonnal use due to amanufacturing defect when installed and operated according to the owner's manual endosed with the unit will
be repaired or replaced with a
unit of comparable value, at the option
of PUSA or POC, without charge to you for parts or actual repair work. Replacement units and/or parts supplied underthis warranty may be
new or rebui~ at the option of PUSA or POCo
THISLIMITEDWARRANTYAPPLIESTOTHEORIGINALOR ANYSUBSEQUENTOWNER OFTHIS PIONEER PRODUCTDURINGTHEWARRANTYPERIODPROVIDEDTHE
PRODUCT
WAS PURCHASEDFROM AN AUTHORIZED PIONEER DISTRIBUTOR/DEALER IN THE U.S.A.OR CANADA. YOU WILL BE REQUIREDTO PROVIDE A SALES
RECEIPTOROTHERVALIDPROOFOFPURCHASESHOWING THEDATE OF ORIGINALPURCHASEOR, IFRENTED, YOUR RENTALCONTRACTSHOWINGTHEPLACE
ANDDATEOFFIRST
RENTAL INTHEEVENTSERVICEISREQUIRED,THEPRODUCTMUSTBEDELIVEREDWITHINTHEWARRANTYPERIOD,TRANSPORTATIONPREPAID,
ONLY FROM WITHIN
THE COUNTRY OF PURCHASE AS EXPLAINEDINTHIS DOCUMENT. YOU WILL BE RESPONSIBLEFOR REMOVAL AND INSTALLATION OF THE
PRODUCT. PUSAOR POC, AS APPROPRIATE,
WILL PAY TO RETURN THE REPAIREDOR REPLACEMENTPRODUCTTO YOU WITHINTHECOUNTRYOF PURCHASE.
PRODUCTWARRANTVPERIOD f4m ld.b2r
Car Stereo Products 1 Year 1 Year
The warranty perlod for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IFTHISPRODUCTWASPURCHASEDFROMANUNAUTHORIZEDDISTRIBUTOR, THEREARENOWARRANTIES, EXPRESSORIMPLIED,INCLUDINGTHE IMPLIEDWARRANTY
OFMERCHANTABILITYANDTHEIMPLIEDWARRANTY
OF FITNESS FORA PARTICULARPURPOSEANDTHIS PRODUCTISSOLDSTRICTLY "AS IS"AND"WITH ALL FAULTS".
PIONEERSHALLNOTBELIABLEFORANYCONSEQUENTIALANDIORINCIDENTALDAMAGES.
PIONEER DOESNOTWARRANTANY PRODUCTLISTEDABOVEWHEN IT
IS USED IN ATRADEOR BUSINESS OR IN ANYINDUSTRIAL OR COMMERCIALAPPLICATION.
THISWARRANTYDOESNOTAPPLYIFTHEPRODUCTHAS BEENSUBJECTEDTO POWER
IN EXCESSOFITSPUBLISHEDPOWER RATlNG.
THIS WARRANTYDOESNOTCOVER DISPLAYSCREENSDAMAGEDBYSTATIC,NON-MOVING,IMAGESAPPLIED FOR LENGTHY PERIODS(BURN-IN).
THISWARRANTYDOESNOTCOVERTHECABINETORANYAPPEARANCErTEM,USERATTACHEDANTENNA,ANYDAMAGETORECORDSORRECORDlNGTAPESORDISCS,ANY
DAMAGETOTHEPRODUCTRESULTlNGFROM
AL TERATlONS,MOOIFlCATlONSNOTAUTHORIZED IN WRITINGBYPIONEER,ACClDENT,MISUSE OR ABUSE, DAMAGEDUETO
UGtmlNGORTOPOWERSURGES,SUBSEQUENTDAMAGEFROMLEAKING,DAMAGEFROMN>PERATlVEBATTERIES,ORTHEUSEOFBATTERlESNOTCONFOR~TOTHOSE
SPECIAEDINTHEOWNER'SMANUAL
THISWARRANTYDOESNOTCOVERTHECOST
OF PARTS OR LABORWHICHWOULDBEOTHERWISEPROVIDEDWITHOUTCHARGEUNDERTHISWARRANTY OBTAfED FROM
ANYSOURCEOTHERTHANAPIONEERAUTHORIZEDSERVJCEcotIPANYOROTHERDESlGNATEDLOCATION.THISWARRANTYDOESNOTCOVERDEFECTSORDAMAGECAUSED
BYTHEUSEOFUNAUTHORIZEDPARTSORLABORORFROMIMPROPERMAINTENANCE.
ALTERED,DEFACED,ORREMOVEDSERIALNUMBERSVOID
THIS ENTIREWARRANTY
NOOTHERWARRANTIES
IN THE U.S.A. -PIONEER LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITYANDFITNESSFORAPARTlCULARPURPOSE, TO APERIODNOTTOEXCEEDTHEWARRANTYPERIOD. NOWARRANTlESSHALLAPPLY AFTERTHE
WARRANTYPERIOD. SOMESTATESDONOT
ALLOW LIMITATIONSON HOWLONGANIMPLIEDWARRANTYLASTSANDSOMESTATESDONOTALLOWTHEEXCLUSIONS
OR LIMITATIONSOFINCIDENTALOR CONSEQUENTIALDAMAGES, SOTHEABOVE LIMITATIONS OREXCLUSIONS
MAY NOT APPL YTO YOU. THIS WARRANTYGIVES
YOU SPECIFIC
LEGAL RIGHTS ANDYOU MAY HAVEOTHER RIGHTS WHICH MAY VARYFROM STATE TO STATE.
IN
CANADA· EXCEPT AS EXPRESSLYPROVIDEDHEREIN,THEREARENOREPRESENTATIONS,WARRANTIES,OBLIGATIONS OR CONDITIONS,IMPLIED,STATUTORY
OR OTHERWISE,APPLICABLETOTHIS PRODUCT.
TO OBTAIN SERVICE
In the U.S.A. or Canada to receive warranty service you need to present your sales receipt or your rental contract showing place and date of original owner's transaction.
Y.SA - Please contact one of the following Pioneer partners to obtain service:
Your Authorized Pioneer Dealer - Your Pioneer Dealer may repair or replace your unit, or refer you to an Authorized Pioneer Service Company. Your sales receipt should
list the contact information (phone number, fax, email, etc.)
for your Dealer.
Your Authorized Pioneer Service Company -Can perform repairs for most Car Electronics products and can advise
other options as applicable. Please access the
Pioneer website at
www.pioneerelectronlcs.com and click on Service and Support and select Authorized Service Locator to find the nearest Pioneer servicer.
Pioneer Electronics Service -Can advise the optimal service option
for your model and geographic location. Please reference the information listed below and phone,
email or access the Pioneer website to contact Pioneer.
~ -POC has anumber of Authorized Service Companies should your product require service. Contact Pioneer of Canada as listed below to obtain alocal service location.
Shipping Your Unit for Service· Please package it carefull'( and send it, transportation prepaid by atraceable, insured method, to an Authorized Service Company or Pioneer.
Use adequate padding material to prevent damage in
transi. Include your name, address and telephone number where you can be reached during business hours.
On all complaints and concerns in the U.S.A. call Customer Support at 1-800-421-1404, or, in Canada, call Customer Satisfaction at 1-877-283-5901.
IN THE U.S.A. IN CANADA
For hook-up and ~peration of your unit or to locat~ an For additional information on this warranty, please call or write:
AuthOrized Service Company, please call or write: CUSTOMERSATISFACTIONGROUP
PIONEER ELECTRONICS SERVICE, INC. PIONEER ELECTRONICS OF CANADA INC
P.O. BOX 1760 300 ALLSTATE PARKWAY' .
LONG BEACH, CALIFORNIA 90801 MARKHAM ON L3R OP2
1-800-421-1404 [phone]' 1-877-283-5901
http://www . pioneerelectronics.com http://www.pioneerelectronics.ca
DISPUTERESOLUTION
IN THE U.S.A .• Following our response to any initial request to Customer Support, should adispute arise between you and Pioneer, Pioneer makes available its Complaint
Resolution Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program
before you exercise any rights under, or seek any remedies, created
by Title Iof the Magnuson-Moss Warranty-Federal Trade ConYnission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-421-1404 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer product was purchased. After the complaint
has been explained to the representative, aresolution number will be issued. Within
40 days of receiving your complaint, Pioneer will investigate the dispute and will either:
(1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing
informing you
why it will not take any action.
IN
CANADA -Call the Customer Satisfaction Manager at [phone] to discuss your complaint and to obtain aprompt resolution.
RECORDTHE PLACEAND DATEOFPURCHASE FOR FUTUREREFERENCE
Model No. Serial No. Purchase Date _
Purchased From KEEP THIS INFORMATION AND YOUR SALES RECEIPT
IN ASAFE PLACE <
CRY1276-A/U >
Printed in China