Pioneer PRA-BD11 User manual
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2004
PRA-BD12
PRA-BD11
RRV2971
SDI AES/EBU INPUT BOARD
PRA-BD11
SDI AES/EBU OUTPUT BOARD
PRA-BD12
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
PRA-BD11 ZUCYV/WL DC Power supply from other system
PRA-BD12 ZUCYV/WL DC Power supply from other system
For details, refer to "Important symbols for good services".
T-ZZY JULY 2004 printed in Japan
PRA-BD11
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are knownto the state of California to cause
cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 – Proposition 65
PRA-BD11 3
5678
5678
C
D
F
A
B
E
CONTENTS
1. SPECIFICATIONS .............................................................................................................................................4
2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................6
2.1 PACKING and EXTERIOR SECTION.........................................................................................................6
2.1.1 PRA-BD11 (SDI AES/ EBU INPUT BOARD ) ......................................................................................6
2.1.2 PRA-BD12 (SDI AES/ EBU OUTPUT BOARD) ...................................................................................8
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................10
3.1 BLOCK DIAGRAM....................................................................................................................................10
3.2 OVERALL CONNECTION DIAGRAM ......................................................................................................12
3.3 [PRA-BD11]: DINB ASSY (1/4).................................................................................................................14
3.4 [PRA-BD11]: DINB ASSY (2/4).................................................................................................................16
3.5 [PRA-BD11]: DINB ASSY (3/4).................................................................................................................18
3.6 [PRA-BD11]: DINB ASSY (4/4).................................................................................................................20
3.7 [PRA-BD12]: DOOB ASSY (1/2)...............................................................................................................22
3.8 [PRA-BD12]: DOOB ASSY (2/2)...............................................................................................................24
4. PCB CONNECTION DIAGRAM ......................................................................................................................26
5. PCB PARTS LIST ............................................................................................................................................30
6. ADJUSTMENT ................................................................................................................................................31
7. GENERAL INFORMATION .............................................................................................................................32
7.1 DIAGNOSIS..............................................................................................................................................32
7.1.1 [PRA-BD11]: HOW TO OPERATION CHECK ....................................................................................32
7.1.2 [PRA-BD11]: LIST OF STATUS LED INDICATION ............................................................................37
7.1.3 [PRA-BD11]: EXTERNAL I/F SPECIFICATIONS ...............................................................................38
7.1.4 [PRA-BD11]: TROUBLESHOOTING ..................................................................................................39
7.1.5 [PRA-BD12]: HOW TO OPERATION CHECK ....................................................................................45
7.1.6 [PRA-BD12]: LIST OF STATUS LED INDICATION ............................................................................48
7.1.7 [PRA-BD12]: TEST MODE .................................................................................................................50
7.1.8 [PRA-BD12]: OPERATION CHECK OF THE ASSY ...........................................................................51
7.1.9 [PRA-BD12]: TROUBLESHOOTING ..................................................................................................52
7.1.10 DISASSEMBLY ................................................................................................................................59
7.1.11 INSTALLATION.................................................................................................................................60
7.2 IC INFORMATION ....................................................................................................................................70
8. PANEL FACILITIES .........................................................................................................................................96
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
PRA-BD11
4
1234
1234
C
D
F
A
B
E
1. SPECIFICATIONS
[PRA-BD11]
SDI input connectors:
Connector configuration ................ BNC (1)
Input impedance ............................. 75 Ω
Supported video standard .............. SMPTE 259 M-C compliant
(270 Mb/S, 525i/625i 4:2:2 component input)
Supported audio standard .............. SMPTE 272 M compliant
(Linear PCM, 48 kHz, 20-bit, channel 1/2) *1, *2, *3
AES/EBU input connectors:
Connector configuration ................. BNC (1)
Input impedance ............................. 75 Ω
Supported audio standard .............. AES-3ID-1995 compliant (Linear PCM, 48 kHz, 16/18/20 bit, industrial format) ∗1,∗3, ∗4
General:
Power supply ................................. +5 V DC (supplied internally by PRV-LX1)
Weight ........................................... 0.3 kg
Dimensions .................................... 195.5 (W) x 101 (D) x 28.4 (H) mm (including projections)
Ambient operating temperature ..... +5 to +35 °C (PRV-LX1 it mounts)
Ambient operating humidity ........... 5 to 85 % RH (no condensation)
∗1 Quantization bits input to the PRV-LX1 are converted to 16 bits.
∗2 Audio channel 3/4 input is not supported.
SDI audio can only be selected during SDI video input (audio only cannot be selected).
∗3 Compressed audio cannot be input.
∗4 Digital audio input of the CP-1201 consumer format is not supported.
[PRA-BD12]
SDI output connectors:
∗1
Connector configuration ................. BNC (1)
Output impedance .......................... 75 Ω
Supported video standard .............. SMPTE 259 M-C compliant
(270 Mb/S, 525i/625i 4:2:2 component output)
Supported audio standard ............. SMPTE 272 M compliant
(Linear PCM, 48 kHz, 20-bit, channel 1/2) ∗2, ∗3
AES/EBU output connectors : ∗1
Connector configuration .................. BNC (1)
Output impedance ........................... 75 Ω
Supported audio standard ............... AES-3ID-1995 compliant
(Linear PCM, 48 kHz industrial format) ∗2, ∗3
General:
Power supply .................................. +5 V DC (supplied internally by PRV-LX1)
Weight ............................................ 0.3 kg
Dimensions ...................................... 195.5 (W) x 101 (D) x 28.4 (H) mm (including projections)
Ambient operating temperature ...... +5 to +35 °C (PRV-LX1 it mounts)
Ambient operating humidity ............ 5 to 85% RH (no condensation)
∗1 Video/audio data is not output when playing back content containing signals preventing unauthorized copying to protect
copyright holders, etc.
The PRA-BD12 does not support through output of SDI and AES/EBU signals via the PRA-BD11 (SDI AES/EBU input
board).
∗2 Compressed audio cannot be output.
∗3 Output of the CP-1201 consumer format is not supported.
• Specifications and design are subject to possible modification without notice.
PRA-BD11 5
5678
5678
C
D
F
A
B
E
(DDD1267)
(DDD1266)
(DKP3673) (DKP3674)
(26pin)
(30pin)
• 4-pin cable (M) • 4-pin cable (L)
Short cable (1pin color : White)
(approx. 90 mm) Long cable (1pin color : Blue)
(approx. 130mm)
• FFC cable (M)
(DDD1267)
• FFC cable (L)
• FFC cable (L)
Narrow
Wide
(30pin)
Wide
Accessories
PRA-BD11 PRA-BD12
• IN Terminal Cover..1
(DNF1692)
• OUT Terminal Cover..1
(DNF1693)
Cushion
(DEC2716)
Cable Support
(DNG1090)
Binder
(ZCA-SKB90BK)
Ferrite Core
(DTH1188)
Cable Sheet
(DEC2710)
• Operating Instructions
(DRC1218)
• Warranty Card
(For Japan)
• Warranty Card PUSA2
• Board Connection Caution
(DRY1224)
• OPB User Sheet
(For U.S.)
(DRY1228)
• Screw..x2
(PMB40P070FCU)
• Screw..x2
(BMZ30P060FNI)
• Screw..x2
(PMB40P070FCU)
• Screw..x2
(BMZ30P060FNI)
• Nyron Rivet...x1
(DEC2698)
• Nyron Rivet...x1
(DEC2698)
• Operating Instructions
(DRC1218)
• Warranty Card
(For Japan)
• Warranty Card PUSA2
• Board Connection Caution
(DRY1224)
• OPB User Sheet
(For U.S.)
(DRY1228)
• Locking Wire Saddle..x1
(DEC1305)
• Locking Wire Saddle..x1
(DEC1305)
Double-sided
tape side
PRA-BD11
6
1234
1234
C
D
F
A
B
E
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING and EXTERIOR SECTION
2.1.1 PRA-BD11 (SDI AES/ EBU INPUT BOARD )
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
×5
26
2, 3, 4
5, 6, 27(x2), 30(x2)
13 14
16
32(x2)
17
12
7
23
19
15
11
31
17
9
2829
28
26
26
26
26
26
26
26
29
1
21
10
24
25
18
8
22
20
11
∗How to remove DINB Assy.
(Refer to "7.1.10 DISASSEMBLY")
AA
PRA-BD11 7
5678
5678
C
D
F
A
B
E
PRA-BD11 Parts List
Mark No. Description Part No.
1 DINB Assy DWV1200
2 Flexible Cable (26P) DDD1266
(FFC cable (M))
3 Flexible Cable (30P) DDD1267
(FFC cable (L))
4 Connector Assy DKP3673
(4-pin cable (M))
5 Locking Wire Saddle DEC1305
6 Nyron Rivet DEC2698
7 Shield Case UP DNF1691
8 IN Terminal Cover DNF1692
NSP 9 IN Case Bottom DNF1694
NSP 10 Warranty Card ARY1093
NSP 11 Polyethylene Bag DHL1113
NSP 12 Polyethylene Bag DHL1139
13 Operating Instructions DRC1218
(English, French,Duch, Japanese)
NSP 14 Warranty Card PUSA2 DRY1210
15 Board Connection Caution DRY1224
NSP 16 OPB User Sheet DRY1228
NSP 17 Polyethylene Bag Z21-004
(0.03 x 60 x 120)
NSP 18 Polyethylene Bag Z21-010
(0.018 x 100 x 230)
NSP 19 Polyethylene Bag Z21-019
(0.06 x 235 x 320)
20 Upper Pad DHA1606
21 Unit Pad DHA1607
22 Accessory Box DHA1609
23 Upper Spacer DHA1612
24 Packing Case IN DHG2435
25 Master Carton IN DHG2436
26 Screw BBZ30P060FNI
27 Screw BMZ30P060FNI
28 Lock Washer DBG1003
29 JAM Nut DBN1005
30 Screw PMB40P070FCU
NSP 31 Name Label IN DRW2204
NSP 32 Serial Paper DRW1846
PRA-BD11
8
1234
1234
C
D
F
A
B
E
2.1.2
PRA-BD12 (SDI AES/ EBU OUTPUT BOARD)
×5
30
2, 3
4, 5, 31(x2), 34(x2)
6, 7, 11, 12, 35
20
15
8
26
22
16
17
20
20
27
10
3233
32
30
30
30
30
30
30
30
33
1
24
13
28
29
21
9
25
23 14
19
37(x2)
18
11
36
∗How to remove DOOB Assy.
(Refer to "7.1.10 DISASSEMBLY")
BB
PRA-BD11 9
5678
5678
C
D
F
A
B
E
PRA-BD12 Parts List
Mark No. Description Part No.
1 DOOB Assy DWV1201
2 Flexible Cable (30P) DDD1267
(FFC cable (L))
3 Connector Assy DKP3674
(4-pin cable (M))
4 Locking Wire Saddle DEC1305
5 Nyron Rivet DEC2698
6 Cable Sheet DEC2710
7 Cushion DEC2716
8 Shield Case UP DNF1691
9 OUT Terminal Cover DNF1693
NSP 10 OUT Case Bottom DNF1695
11 Cable Support DNG1090
12 Ferrite Core DTH1188
NSP 13 Warranty Card ARY1093
NSP 14 Polyethylene Bag DHL1113
NSP 15 Polyethylene Bag DHL1139
16 Operating Instructions DRC1218
(English, French,Duch, Japanese)
NSP 17 Warranty Card PUSA2 DRY1210
18 Board Connection Caution DRY1224
NSP 19 OPB User Sheet DRY1228
NSP 20 Polyethylene Bag Z21-004
(0.03 x 60 x 120)
NSP 21 Polyethylene Bag Z21-010
(0.018 x 100 x 230)
NSP 22 Polyethylene Bag Z21-019
(0.06 x 235 x 320)
23 Upper Pad DHA1606
24 Unit Pad DHA1607
25 Accessory Box DHA1609
26 Upper Spacer DHA1612
27 Bracket Spacer DHA1617
28 Packing Case OUT DHG2437
29 Master Carton OUT DHG2438
30 Screw BBZ30P060FNI
31 Screw BMZ30P060FNI
32 Lock Washer DBG1003
33 JAM Nut DBN1005
34 Screw PMB40P070FCU
35 Binder (SKB-90BK) ZCA-SKB90BK
NSP 36 Name Label OUT DRW2205
NSP 37 Serial Paper DRW1846
PRA-BD11
10
1234
1234
C
D
F
A
B
E
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
Main Device
• SDI section
• AES/EBU section
• Common section
∗1
Note ;
∗1 : 27MHz clock from PRV-LX1
∗2 : 27MHz clock to PRV-LX1
∗2
IC Name Function
IC8103 (GS9025A) SDI Receiver SDI Receiver receive a SDI signal, and extract the 270MHz clock and equalize the signal.
IC8108 (GS9020A) SDI Decoder SDI Decoder receive the output of SDI Receiver, and perform the serial/parallel conversion and
27MHz clock generation.
IC8106 (GS9023A) Audio Processor Audio Processor demultiplex the video/audio signal from the SDI parallel, and each output it.
IC Name Function
IC8301 (CS8414-CS) AES/EBU
Receiver
AES/EBU Receiver receive an AES/EBU signal, and judge a format.
Then generate audio data and output it.
IC Name Function
IC8201
(XC2S50-5PQ208C) FPGA
FPGA convert a format of the video signal and the audio signal which extracted from SDI and
AES/EBU signals.
Switching control of 27MHz main clock of PRV-LX1, and the control of each IC.
CN8101
BNC
Connector
CN8203
FFC (30P)
IC8103
GS9025A
SDI Receiver
• SDO
• SDO#
• SCO
• SCO#
• 20 DOUT [0:9]
• PCLKOUT
• AOUTA
• AOUTB
• WCOUT
• 23 DOUT [0:9]
Digital Video Data
MAIN Clock
Select
• PCLKOUT (27MHz)
SDI IN
IC8108
GS9020A
SDI Decoder
IC8205
PE9016A
PROM
X8301
27MHz OSC
IC8106
GS9023A
Audio Processor
IC8306
5V →3.3V
Regulator
IC8203
27MHz
Clock Select
IC8201
XC2S50-5PQ208C
FPGA
CN8301
BNC
Connector IC8301
CS8414-CS
AES/EBU Receiver
• 14 SDATA
• 14 FSYNC
• 14 SCK
AES/EBU
IN
SDI Embedded Digital Audio Data
AES/EBU Digital Audio Data
+5V
+5V +3.3V
IC8307
5V →2.5V
Regulator
+2.5V
GND
SDI Video
Format det.
Copy protect det.
SDI Audio
Format det.
AES/EBU
Format det.
Control
Device etc.
Control BUS
JTAG BUS
CN8202
FFC (26P)
CN8201
PH (4P)
From AVIBFrom AVIBFrom AVIB
PRA-BD11
PRA-BD11 11
5678
5678
C
D
F
A
B
E
Main Device
Block, IC Function
Regulator block Generate +3.3V and +2.5V power from +5V power supplied by AVIB
Clock control block Generate 27MHz and 36.864MHz clocks for video and audio from 27MHz clock supplied by AVIB, and
supply to each IC
Clock generation block
Generate 18.432MHz that are a basic clock for RS-232C I/F of FPGA
Work with asynchronization for a audio 36.864MHz clock of the clock control block
Generate 27MHz to use for the simple signal generator function for board check
FPGA (IC8611)
FPGA Communication with RS-232C for inside status display
Communication control with AVIB
Operation setting of each IC in the board and the LED control for status display
CCIR656 video data control
3-wires audio data control
Sampling frequency 96kHz of audio data convert to 48kHz
Generate 6.144MHz and 12.288MHz clocks for audio (dividing by 36.864MHz clock)
Simple signal generator function for board check (switching by a DIP switch)
Digital audio transmitter
(IC8614) Convert 3-wires audio data from the FPGA into AES/EBU data
Embedded audio processor
(IC8613)
Superimposing the 3-wires audio data from the FPGA on the CCIR656 video data from the FPGA, and
convert 8-bit to 10-bit.
Digital video serializer
(IC8617) Convert 10-bit CCIR656 video data from the embedded audio processor to SDI serial data
Regulator
Block
Clock Control
Block
Clock Generate
Block
IC8611
XC2S50-5PQ208C
FPGA
IC8613
GS9023A
Embedded
Audio
Processor
IC8617
GS7032
Digital Video
Serializer
IC8614
AK4103A
Digital Audio
Transmitter
Control Control
CCIR656 Video
CCIR656 Video CCIR656 Video
(Audio Superimposing) SDI Data
3-wires Audio
3-wires Audio
6.144MHz Clock
3-wires Audio
+5V
+3.3V
+3.3V +5V
+5V
+2.5V
+3.3V +2.5V
CN8601
PH (4P)
From AVIBFrom AVIB
CN8610
FFC (7P)
CN8602
FFC (30P)
CN8608
BNC
Connector
SDI OUT
AES/EBU Data
RS-232C Control
CN8609
BNC
Connector
AES/EBU OUT
RS-232C
PRA-BD12
27MHz Clock 27MHz Clock
12.288MHz Clock
27MHz Clock
18.432MHz
Clock
36.864MHz Clock
PRA-BD11
12
1234
1234
C
D
F
A
B
E
3.2 OVERALL CONNECTION DIAGRAM
÷When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷The >mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷: The power supply is shown with the marked box.
A1/4 - A4/4
PRV-LX1
AVIB ASSY (DWV1198)
A
B1/2 - B2/2
B
1234
OFF FSK
DINB ASSY
(DWV1200)
PRA-BD11 PRA-BD12
DOOB ASSY
(DWV1201)
To. PCIB ASSY
(CN2104, CN2103)
To. JKIB ASSY
(CN7613)
To. JKIB ASSY (CN7611)
To. JKIB ASSY (CN7402)
To. PWRB ASSY
(CN2)
To. DECB ASSY
(CN1651, CN1811)
To. PCIB ASSY
(CN2101)
S8602 (DIP- SW)
AKN7032 DKN1192 DKN1192
PRA-BD11 13
5678
5678
C
D
F
A
B
E
Connection and Pin Function
DINB ASSY (DWV1200)
CN8201 ↔AVIB ASSY (CN3203)
CN8202 ↔AVIB ASSY (CN5502)
CN8203 ↔AVIB ASSY (CN5501)
CN8101 ↔External Unit
CN8301 ↔External Unit
No. Name I/O Function
1, 4 GND −Ground
2, 3 +5V −+5V power supply input
No. Name I/O Function
2 AES_LRCK O LR clock output for AES/EBU
3 AES_DAI O Data output for AES/EBU
4 AES_BCK O Audio clock output for AES/EBU
6 SDI_LRCK O LR clock output for SDI embedded audio
7 SDI_DAI O Data output for SDI embedded audio
8 SDI_BCK O Audio clock output for SDI embedded audio
11-25 SDI [0 : 7] O SDI digital video signal output
27 CLK_27MSDI_SEL O 27MHz clock output
29 CLK_27MAVIB I 27MHz clock input
CN8610 ↔RS-232C jig GGF1348
(DVD interface jig for service)
CN8602 ↔AVIB ASSY (CN5503)
No. Name I/O Function
1 DINB_EXIST O A signal to judge installation of DINB
H : DINB is installed.
2 SDI_VALID O
Lock to the SDI signal, and a signal to show
whether the signal is a component SD
signal or not.
H:Lock to a SDI signal, and signal format is valid.
L:SDI signal is invalid or there is no input.
3 SDI_NP O
Inputted video signal to SDI to show
whether the signal is NTSC or PAL.
H : NTSC , L : PAL
4 SDI_LOCK O
Signal to show whether the audio signal
that is included in SDI signal is locked or
not.
H:Locks to the embedded audio
L:Unlocks to the embedded audio
5 SDI_RST I DINB system reset signal input
6 AES_ERROR O
A signal to show whether the error of
AES/EBU signal exists.
H:There is no error with AES/EBU signal.
L:There is an error with AES/EBU signal.
7 MODE_SEL I
Set the operating mode of the AES/EBU
receiver.
H:Clock output (master) mode
L:Clock input (slave) mode
8-25 TP [1 : 16] O FPGA test signal output
No. Name I/O Function
1 GND I GND input for SDI
2 SDI I
SDI input Signal level is PECL (800mVp-p) at input
No. Name I/O Function
1 GND I GND input for AES/EBU
2 AES/EBU I
AES/EBU input Signal level is 1Vp-p at input
CN8608 ↔External Unit (SDI input)
DOOB ASSY (DWV1201)
CN8601 ↔AVIB ASSY (CN3204)
No. Name I/O Function
1, 4 GND −Digital ground
2, 3 +5V −+5V power supply input
CN8609 ↔External Unit (AES/EBU input)
Switch 1
Switch 2
Switch 3
Switch 4
OFF side
ON side
1234
1
2
3
4
5
6
7
8
OFF FSK
S8602 (DIP switch)
No. Name I/O Function
1 GND −Digital ground
2 N.C. −Reserve
3 SDO_ENA I/O DOOB system control signal (LVTTL level)
4 XRESET I System reset input (LVTTL level)
5 GND −Digital ground
6 SDO_LRCK I 3-line audio LR clock input (LVTTL level)
7 SDO_DAI I 3-line audio data input (LVTTL level)
8 SDO_BCK I 3-line audio bit clock input (LVTTL level)
9 N.C. −Reserve
10 GND −Digital ground
11 SDO_D0 I CCIR Rec656 data input (LVTTL level)
12 GND −Digital ground
13 SDO_D1 I CCIR Rec656 data input (LVTTL level)
14 GND −Digital ground
15 SDO_D2 I CCIR Rec656 data input (LVTTL level)
16 GND −Digital ground
17 SDO_D3 I CCIR Rec656 data input (LVTTL level)
18 GND −Digital ground
19 SDO_D4 I CCIR Rec656 data input (LVTTL level)
20 GND −Digital ground
21 SDO_D5 I CCIR Rec656 data input (LVTTL level)
22 GND −Digital ground
23 SDO_D6 I CCIR Rec656 data input (LVTTL level)
24 GND −Digital ground
25 SDO_D7 I CCIR Rec656 data input (LVTTL level)
26 GND −Digital ground
27 N.C. −Reserve
28 GND −Digital ground
29 27MSDO I27MHz clock input (LVTTL level)
30 GND −Digital ground
No. Name I/O Function
1 GND −Analog ground
2 DATA O Output (800mVp-p ±10%,
output impedance 75Ω, 270Mbps)
No. Name I/O Function
1 GND −Analog ground
2 DATA O AES/EBU output (1.0Vp-p ±20%,
output impedance 75Ω, 3.072Mbps)
No. Name I/O Function
1 N.C. −Reserve
2 GND −Digital ground
3 +5V −+5V power supply input
4 CTS I Reserve (RS-232C CTS inut at LVTTL level)
5 RTS O Reserve (RS-232C RTS inut at LVTTL level)
6 RxD I Reserve (RS-232C RxD inut at LVTTL level)
7 TxD O RS-232C TxD input (LVTTL level)
No. Name Function Land Setting for Land
1 Test mode setting OFF : Normal operation
ON : Test mode TP8660 OFF : Open
ON : L (GND)
2NTSC/PAL setting
at test mode
OFF : Video is NTSC at test mode
ON : Video is PAL at test mode TP8661 OFF : Open
ON : L (GND)
3, 4 Reserve −−−
PRA-BD11
18
1234
1234
C
D
F
A
B
E
3.5 [PRA-BD11]: DINB ASSY (3/4)
A3/4
A3/4
DINB ASSY (DWV1200)
2/4A
2/4
A
2/4
A
2/4, 4/4
A
2/4, 4/4
A
1/4, 2/4
A
PRA-BD11 19
5678
5678
C
D
F
A
B
E
A3/4
PRA-BD11
20
1234
1234
C
D
F
A
B
E
3.6 [PRA-BD11]: DINB ASSY (4/4)
A4/4
A4/4
DINB ASSY (DWV1200)
1/4, 2/4A
1/4, 2/4
A
1/4, 2/4
A
1/4, 2/4
A
2/4, 3/4
A
1/4
A
Other manuals for PRA-BD11
1
This manual suits for next models
1
Table of contents
