Pioneer 3CB100 Series User manual

Engineering Excellence
Installation Guide
Two Handle Lavatory Faucet:
3CB100* • 3BR120 • 3BR300*•
3CB101* • 3BR130* • 3BR310*•
3PR100* • 3BR200* • 3BR320•
3AM100* • 3BR210* • 3BR330*•
3BR100* • 3BR220 • 3MT100*•
3BR110* • 3BR230* • 3MT110*•
This product meets the following standards:
ASME A112.18.1 •
ANSI A117.1 •
ANSI / NSF 61, SECTION 9 •
CUPC / IAPMO LISTED / *ADA COMPLIANT•
CONTAINS NO MORE THAN 0.25% WEIGHTED AVERAGE LEAD •
CONTENT
Pioneer Industries, Inc. © 2012

Thank you for purchasing this Pioneer quality product.
Prior to Installation
Observe all local plumbing and building codes before you begin •
installation.
Carefully shut off both hot and cold water supplies from under the sink. •
Plug the sink drain with a soft cloth to prevent intrusion of debris or the •
loss of any faucet parts.
For replacement installations, carefully remove the existing •
faucet and clean the entire surface of the sink mounting holes.
Pioneer reserves the right to make changes in the design of faucets without •
notice as specied in the pricebook.
2
Tools Required
Adjustable-
Wrench
Sealant Tape Rags
Plumbers Putty

Thank you for purchasing this Pioneer quality product.
Prior to Installation
Observe all local plumbing and building codes before you begin •
installation.
Carefully shut off both hot and cold water supplies from under the sink. •
Plug the sink drain with a soft cloth to prevent intrusion of debris or the •
loss of any faucet parts.
For replacement installations, carefully remove the existing •
faucet and clean the entire surface of the sink mounting holes.
Pioneer reserves the right to make changes in the design of faucets without •
notice as specied in the pricebook.
2
Faucet Installation
Clean lavatory surface (A) from oil, grease or debris.•
Apply adequate amount of plumbers putty or sealant underneath of base •
plate.
Lead the faucet shank (B) through faucet holes. •
Slide the mounting washers (C) through faucet shank (B). •
Thread and hand tighten the mounting nut (D) through faucet shank (B). Make •
sure both side of mounting nuts (D) are securely tighten.
3

Pop-Up Drain Installation
Remove the pop-up stopper (E) and pop-up ange (F) from the pop-up 1.
assembly.
Apply adequate amount of plumbers putty underside of pop-up ange (F) 2.
then insert pop-up drain assembly from underside of the sink and secure the
pop-up ange (F) from the top.
Rotate the drain body so that horizontal rod hole faces back of the faucet.3.
Hold the pop-up assembly in place and tighten the locknut (G).
Remove the excess putty. Connect the trap (H) (check manufacturer’s instruc-4.
tions for installation).
Remove rod nut (I).5.
Ensure the washer (K) is in place (for brass pop-up only). Insert rod (J). Tighten 6.
the rod nut (I).
Push rod down to open drain. Insert the pop-up stopper (E) carefully. Test if the 7.
pop-up stopper (E) is working properly.
Connect pop-up bracket to the rod using clip (L). Tighten the thumbscrew (M) 8.
to connect pop-up bracket to pop-up lift rod.
4

Pop-Up Drain Installation
Remove the pop-up stopper (E) and pop-up ange (F) from the pop-up 1.
assembly.
Apply adequate amount of plumbers putty underside of pop-up ange (F) 2.
then insert pop-up drain assembly from underside of the sink and secure the
pop-up ange (F) from the top.
Rotate the drain body so that horizontal rod hole faces back of the faucet.3.
Hold the pop-up assembly in place and tighten the locknut (G).
Remove the excess putty. Connect the trap (H) (check manufacturer’s instruc-4.
tions for installation).
Remove rod nut (I).5.
Ensure the washer (K) is in place (for brass pop-up only). Insert rod (J). Tighten 6.
the rod nut (I).
Push rod down to open drain. Insert the pop-up stopper (E) carefully. Test if the 7.
pop-up stopper (E) is working properly.
Connect pop-up bracket to the rod using clip (L). Tighten the thumbscrew (M) 8.
to connect pop-up bracket to pop-up lift rod.
4
Main Supply Connection
Connect the faucet shank to inlet supply lines (N). Connect the supply stops •
(O) to the inlet supply lines (N) (left is hot water supply and right is cold water
supply). Make sure inlet supply lines (N) are securely tighten. Do not overtight-
en.
Turn on water. Check for any leaks. Make sure all the connections are secure.•
Remove aerator (P).•
Open the handle.•
Flush and allow water to run at full ow for at least one minute.•
Replace aerator (P).•
For more care information or trouble shooting inquiries about your
Pioneer product, please see the contact information on the back page.
5

3325 S. Gareld Ave | City of Commerce, CA 90040
Telephone: [phone] | [phone] | Fax: [phone]
Hours: M - F, 7:30am to 5:00pm PST
Engineering Excellence