Turn on the power switch after the device is powered. Group A,B,C light indictocwill
light up and turn off automati@lly after 3 se@nds. This means it mds with lml
power and ente6 into the steady mode. lts default is under minimum brightnss-
5 When either Group A, B or C was light up, to join other groups, simply press
the group button that you want. To close other groups, simply press the group
button thatyou want. ln case of ABC in the same Eroup, AB in the same group
or AC in the same group, the default of brightness adjustment is under the light
of Group A. lf BC are in the same group, the default of brightness adjustment is
under the light of Group B.There are any groups of lights in groups of the same
can be adjusted. When you adjust the light as shown in Picture O, the Pictures
@ @ @ will change accordingly. When you adjust the light as shown in Picture
@, the Pictureso O @ will change accordingly. When you adjust the light as
shown in Picture @, the Pictures @ @ @ will change accordingly. When you
adjust the light as shown in Picture @, the Pictures @ @ @ @ will change
accordingly.
Flash Sync Mode
1. Using flash function must have a PC cable or Pixel King Pro transmitter
2. Using LED light as a tcnsmifting trigger, both (tEnsmitting and receiving) LED light need to
synchronous. Synchronous procedure same as Steady Synchrcnous Mode. Using the PC
sync cord to @nnect tEnsmitting LED light and cmeE, also turn on the LED flash settlng
button. Now when you press the shutter release on the GmeE, the LED light which under
the same channeugroup will be triggered. Flash sync setting and steady synchronous
stting are the sme.
3.Using King PRO tENmitter to triggetfirst, Alsoneedtosynchronousfirst.Then, hold
dom the Grup B sync sik}l button of the LID light and blm on the pMr sitcfi
und tne kht irdizttr of grup B lc€p blinhng. Rdeas the G@p B rync sitdr butbn
Ihff, hdd tE C lGry of lftE Prc ard trm s the porer si!d[ ttE display will shw:
CodirE ...whth rc6 tlE dEnrel rEt*fng b pGirE After the dEnnel is mathed
suc$fu|V, Grcup B liglt indiztor of LID liglt will nrm off automati@lly. Nw, ,}eu
hrye to restart the King Po tEnsmitter lf channel matdring is uEucc$fu|, deas
repeat the action. (For King Prc EatuB, pleas refer to King Prc user manual)
Under the steady mode, \r'ou cn adjust the tID lEtrt by rccting the adjLsErt daL 6deie
to illlrc bdghtE and @r,tedodoi* to rcdre brightE. Ihere are 30 l6€b d a4erEE
rI
UsirE flsh mode, affEr entering into tE steady mode, prc the flah euing siu$ hrtbn nd
li8lt up the light indizbr, tED lL*t will tum off and enter into ttre fla*r mode. Urds tE Hr
mode , the adjustmert of brighbs is iMlid . Pres the flash sltjng sib*l button €ah , ad
tum off the flash mode, @n restffi the original Etting of steady mode. f 'pu r the f,dr
fundion, \&u ned a PC eble or Pirel King PE tEnsmitter to tElMitslndrlm irstt-dir
(the PC @ble and King Prc tEnsmitter need to be ordered spactely)
Steady Synchronous Mode
1. When using the wirele$ slnc mode, both (tEnsmitting and reMng) LED liEht reed to
synchronous. First, on the tElMitting tfD light, pl6 and hold G@p A button tH tum
the power on. Rdeas the Grcup A button when the Grcup A indiEto. is fld{.E S€qd,
on the receiving LED litfit, pt6 and hold Grcup B bufton then tum tlE porEr m Relee
the Group B button when the Grcup B indi@tor is flashing.
The Grcup B indi@tor light willtum offwhen the rynchrcnous is finished. lf lou Ent to
st mutti @ivirg t.ED l€hts, iust Ep€at tiE aboE p.oedue- Ihe tEtMittirt LED light
need to restart s,hen finislr€d the syndlre
2, Under the steady mode, prs Co+ A syrE hrtb.r to inn it m ard light up the
light indi@to., ttEn Etate th€ adiuirErt dial lw. Ya cn adi6t tlE brightE
for those lights which rere set to G@p A sync P6 G@p A syrE button again
and to turn it off.
Under the steady mode, press Grcup B sync buttm to tum it on and light up the
light indi@tor, then rotate the adjustment dial now. You @n adjust the brightness
for those lights which were set to Grcup B sync Press Grcup B sync button atain
and to turn it off.
Under the steady mode, press Grcup C sync button to tum it on and light up the
light indi@tor, then rotate the adjustment dial now. You Gn adjust the brightness
for those lights which were set to Grcup C sync. Press Group C slnc button again
and to turn it off.
6
7
4.After finished the channel matching, press the flash setting switch and light up
the light indicator to enter into the flash mode.
5. Under the flash mode, open the Group A sync and light up the light indicator
to provide the flash signal. The LED lights which have set as Group A sync will
flash. To close Group A, press the Group A sync switch, the light indicator wil
turn off.
I
@@
rr)
