Pknight Atomic SWB FX 960 User manual

Atomic SWB FX 960
user manual

CONTENTS
Introduction 1
Customer Support 1
REMOTE DEVICE MANAGEMENT 2
Control Panel 3
Menu Function
4~5
DMX Modes 6
·
DMX Mode | 3CH 6
·
DMX Mode | 9CH 6~8
·
DMX Mode | 24CH 9~10
Technical Features 11

Introduction
Customer Support
Congratulations and thank you for purchasing the
Atomic SWB FX 960.The Atomic SWB FX 960 is a DMX
intelligent, high powered LED xture.Designed for mobile
or permanent lighting of stages, clubs, dance floors
and churches. please read these operating instructions
carefully to familiarize yourself with the basic operations
of this unit.These instructions contain important safety
information regarding the use and maintenance of this
unit. Please keep this manual with the unit for future
reference.
Pknight Products,LLC provides a toll free customer
support,to provide set up help and to answer any
question should you encounter problems during your set
up or initial operation.You may also visit us on the web at
www.pknightpro.com for any comments or suggestions.
E-mail: [email protected]
We will contact you within 24 hours
Page 1

REMOTE DEVICE MANAGEMENT
NOTE: In order for RDM to work properly, RDM
enabled equipment must be used throughout
the entire system, including DMX data splitters and
wireless systems.
Remote Device Management (RDM) is a protocol that
sits on top of the DMX512 data standard for lighting, and
allows the DMX systems of the fixtures to be modified
and monitored remotely. This protocol is ideal for
instances in which a unit is installed in a location that is
not easily accessible.
With RDM, the DMX512 system becomes bi-directional,
allowing a compatible RDM enabled controller to send
out a signal to devices on the wire, as well as allowing
the fixture to respond (known as a GET command).
The controller can then use its SET command to modify
settings that would typically have to be changed or
viewed directly via the unit’s display screen, including the
DMX Address, DMX Channel Mode, and Temperature
Sensors.
Please be aware that not all RDM devices support all
RDM features, and therefore it is important to check
beforehand to ensure that the equipment that you are
considering includes all of the features that you require.
Page 2

Control Panel
The fixture includes an easy to navigate
system menu control panel display where
all necessary settings and adjustments are
made. (See image above)
MENU :To select the functions
UP :To go forward in the selected functions
DOWN :To go backward in the selected functions
ENTER : Select an option or conrm a selection.
Page 3

Page 4
Menu Function
LED DISPLAY
MAIN click enter
to SUB FUNCTION
→Select the DMX address by UP or DOWN, and click ENTER to save.
→Three DMX modes(3CH,9CH,24CH),Select the DMX modes by UP or
DOWN,and click ENTER to save.CH9 is default
→Built-in programs Effect 1,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 2,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 3,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 4,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 5,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 6,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 7,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 8,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 9,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 10,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 11,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 12,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 13,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.

LED DISPLAY
MAIN click enter
to SUB FUNCTION
→Built-in programs Effect 14,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 15,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 16,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 17,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 18,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
→Built-in programs Effect 19,press ENTER and adjust the speed of the
effect by UP or DOWN (1~50),and click ENTER to save.
Activating sound control mode
→Manually set the brightness of the red LED (r000 ~ r255) and press
ENTER to save.
→Manually set the brightness of the green LED (g000 ~ g255) and press
ENTER to save.
→Manually set the brightness of the blue LED (b000 ~ b255) and press
ENTER to save.
→Manually set the rate of Strobe Effects,Slow to Fast(t000~t255)
→Temperature display | Factory default, do not recommend changing
→Fan switch | Factory default, do not recommend changing
→Automatic power reduction | Factory default, do not recommend changing
→Click ENTER not to restore Factory setting
→Click ENTER to restore Factory setting
Page 5

Page 6
DMX Modes - 3CH | 9CH | 24CH
DMX Mode | 3CH
NO. VALUE NAME FUNCTION
1 000~255 Red Dimmer Red Dimmer, 0% to 100%
2 000~255 Green Dimmer Green Dimmer, 0% to 100%
3 000~255 Blue Dimmer Blue Dimmer, 0% to 100%
DMX Mode | 9CH
NO. VALUE NAME FUNCTION
1 000~255 Total Dimmer Total Dimmer, 0% to 100%
2 000~255 RGB Strobe Red&Green&Blue Strobe Effects,Slow to Fast
3 000~255 Effect Direction 1~127 is one direction, 128~255 is the opposite direction
4 000~255 Auto Mode*A 50 built-in programs/effects
5 000~255 Mode speed Adjust the Speed of Auto Mode,Slow to Fast
Only works for ch4
6 000~255 Background
Color*B Add Some Background Color for monochrome effect
Only works for ch4
7 000~255 Red Dimmer Red Dimmer, 0% to 100%
8 000~255 Green Dimmer Green Dimmer, 0% to 100%
9 000~255 Blue Dimmer Blue Dimmer, 0% to 100%
Auto Mode*A/Background Color*B These parts are described in detail in the table below

DMX TRAITS*A for CH4 - Auto Mode*A
NO. DMX
VALUE FUNCTION
0 000~004 No function
1 005~009 Effect 1
2 010~014 Effect 2
3 015~019 Effect 3
49 240~244 Effect 48
50 245~249 Effect 49
51 250~255 Effect 50
Page 7