Playcore Swing-N-Slide PB 9240 User manual

STOP
READ THIS FIRST
FOR DIRECTIO S
O ATTACHI G
THE TURBO TUBE
SLIDE TO THE
SKY TOWER KIT:
When attaching the Turbo Tube Slide to the Sky Tower Kit,
certain parts of the tower must be modified. Please familiarize
yourself with the steps included in this plan so that you can
adapt your unit properly as you construct it.
o. of Children: Up to 12
Min. Use Zone:
30 ' x 29 '
Set Dim.
18 'W x 14 ' x 12'H
Est. Building Time: 10-12 hr.
30'
29'
PB 9240
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
1-800-888-1232
To register your product visit:
http://www.swing-n-slide.com
Other benefits include information on product warranties, assembly plan updates, joining our
mailing list for new products and promotions, receiving our newsletter, and providing feedback
on products.
IMPORTA T!!
P EASE READ BEFORE BEGINNING ASSEMB Y!!
Please make sure all lumber, hardware and accessory parts are accounted for. If you are
missing anything, please DO OT RETUR to the store where purchased. Please call our
Customer Service Department at the number below.

2
Installation Safety – Have You:
Consulted the assembly instructions supplied with your particular model?
Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components.)
Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.)
Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with
a metal file as needed, and coated fastener ends with lead free paint?
Placed the equipment on level ground, not less than six feet (1. meters) from any structure or obstruction such as a fence, garage,
house, overhanging branches, laundry lines, or electrical wires?
Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto
a hard surface can result in serious injury to the equipment user.)
Verified that suspended climbing ropes, chain,or cable are secured at both ends?
Consulted in assembly instructions of your particular model for minimum use zones?
Used a water sealant on your play set to protect the wood and prevent cracking and warping?
Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply?
Made sure not to allow children to use equipment until it is properly installed?
Made sure to adjust all swings so there is a minimum '' clearance between the swing and the ground surface?
Operating Safety – Have You:
Determined that on-site adult supervision is provided for children of all ages?
Warned children the following before allowing them to use the equipment?
Not to walk close to, in front of, behind or between moving items.
Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the
strength of chain or rope.
Not to swing empty seats or other accessories.
Not to slide down swing chains.
Be sure to sit in the center of the swing seat and other accessories with full weight on the seat.
Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not
limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard.
Not to climb or walk on the top of swing beams, railings or roof.
Not to use equipment in a manner other than intended.
Not to get off equipment while it is in motion.
Not to climb on the equipment when it is wet.
Be sure to go down slides feet first.
Determined that only one child per planned occupant seat should be allowed on this set at one time.
Determined children must be dressed appropriately for play. Avoid hooded jackets, bicycle helmets, clothing with draw strings and
loose fitting clothes which could become entangled or snagged on equipment.
Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself.
Made certain the slide is placed so that is is not in direct sunlight.
Safety Maintenance – At the beginning of every season and twice monthly thereafter:
Rake and check depth of loose fill protective surfacing material to prevent compaction and maintain appropriate depth. Replace as
necessary.
Check all nuts, bolts and C-Links during the usage season for tightness and tighten as required. (It is
particularly important that this procedure be followed at the beginning of each season.)
To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories when outdoors temp dips down to
or below 32° F and take indoors.
Oil all metallic moving parts monthly during usage period.
Check all hardware and equipment for sharp edges during usage season. (Replace when necessary. It is especially
important to do this at the beginning of each new season.)
Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration. Severe rusting or excessive wear,
especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic sleeve
or seat itself are also signs of deterioration. If any of these conditions exist, call 1- 00- -1232 to order replacement accessories.
Sand rusted metal parts and repaint using non-lead based paint.
Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.
Disposal Instructions
When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards
will exist at the time the set is discarded.
Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment.
Save this instruction sheet in the event the manufacturer needs to be contacted.
Observing the following statements and warnings reduces the likelihood of serious or fatal in ury
Safety Checklist for Swing-N-Slide Play Sets and Accessories

3
This product is intended for single family home/residential use only and not intended for use in any public setting.
Placement in any public setting constitutes a misuse of this product.
IMPORTANT!
ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS
According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions
permit stakes to be pulled out easily, cementing into ground is necessary.
• To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 1 " (45mm x 95mm x 457mm) pressure-
treated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2")
galvanized nails per stake into each tower and/or A-frame upright.
• If the unit has a climbing rope, anchor the rope end.
• Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by
using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission “Handbook for Public Playground Safety” lists the following materials and required
depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for Swing•N•Slide kits]:
LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH1in. (mm)
Wood Mulch 9" (229mm)
Double Shredded Bark Mulch 9" (229mm)
Uniform Wood Chips 12" (305mm)
Fine Sand 12" (305mm)
Fine Gravel 12" (305mm)
These depths were derived from the CPSC Handbook. Swing•N•Slide has not done independent tests to determine these required depths.
When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft.
(1. 2 m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have
protective surfacing at least 6 ft. (1. 2 mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m) out from both the back and
front of the swing when the swing is in its rest position.
Sw ng-N-Sl de® MANUFACTURERS LIMITED WARRANTY
Swing-N-Slid ® tak s gr at prid in th quality and durability of our products. Our Manufactur r’s Limit d Warranty provid s confid nc and d monstrat s our commitm nt
to providing quality r sid ntial playground products.
MANUFACTURER’S LIFETIME LIMITED WARRANTY
Swing-N-Slid ® warrants its th rmoform d slid s and climbing mountains to b fr from d f cts in workmanship and mat rials, und r normal us and conditions, for th
lif tim of th product.
MANUFACTURER’S 5 YEAR LIMITED WARRANTY
Sw ng-N-Sl de® warrants its Custom R ady-to-Build Play S t kits and acc ssori s to b fr from d f cts in workmanship and mat rials, und r normal us and conditions,
for a p riod of 5 y ars.
MANUFACTURER’S 5 YEAR LIMITED WARRANTY
Sw ng-N-Sl de® warrants its No-Cut and Wood Compl t R ady-to-Ass mbl Play S t kits against wood rot and t rmit damag , and to b fr from d f cts in
workmanship and mat rials, und r normal us and conditions, for a p riod of 5 y ars for structural wood compon nts.
Cosmet c defects that do not aff ct th structural int grity of th product, or natural d f cts of wood such as warping, splitting, ch cking, twisting, shrinkag , sw lling or
any oth r physical prop rti s of wood that do not pr s nt a saf ty hazard, ar not cov r d by this warranty.
MANUFACTURER’S ONE YEAR WARRANTY
Sw ng-N-Sl de® warrants its canopy roofs and/or tarps, and Timb r GLOVE lumb r wrap to b fr from d f cts in workmanship and mat rials, und r normal us and
conditions, for a p riod of on y ar.
Sw ng-N-Sl de® will r pair, or at its discr tion, r plac any part within th stat d warranty p riod which is d f ctiv in workmanship or mat rials. This d cision is subj ct
to v rification of th d f ct upon d liv ry of th d f ctiv part to Swing-N-Slid ® at 1212 Barb rry Driv , Jan svill , Wisconsin, 53545. Any part(s) r turn d to Swing-N-
Slid ® must hav prior approv d R turn Authorization Numb r and proof of purchas , including th dat of purchas . This warranty is valid only if th product is us d for
th purpos for which it was d sign d and install d at a r sid ntial, singl family dw lling. This warranty is void if th product is put to comm rcial or institutional us . This
warranty do s not cov r (a) products which hav b n damag d by acts of Natur , n glig nc , misus , or accid nt, or which hav b n modifi d or r pair d by
unauthoriz d p rsons; (b) th cost of labor; or th cost of shipping th product, any part, or any r plac m nt product or part.
Sw ng-N-Sl de® DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Swing-N-Slid ® WILL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. This warranty is non-transf rabl and do s not xt nd to th own rs of th product subs qu nt to th original purchas r. Som stat s do not
allow limitations on impli d warranti s or xclusion of incid ntal or cons qu ntial damag s, so th s r strictions may not b applicabl to you. This warranty giv s you
sp cific l gal rights. You may also hav oth r rights, which vary from stat to stat .
Th s warranty also does not apply to:
• Structur s not r ct d, maintain d or insp ct d in conformanc with Sw ng-N-Sl de® installation plans
• Structur s that hav had parts add d or substitut d not in conformanc with Sw ng-N-Sl de® installation plans
•Parts that hav b n modifi d, alt r d or misus d
•Parts that hav not b n us d as d sign d or int nd d
•Damag du to acts of Natur , vandalism, abnormal us or abus as d t rmin d by Sw ng-N-Sl de®
For further information on playground safety, the Consumer Product Safety Commission
(CPSC) publishes the Outdoor Home Playground Safety Handbook which can be downloaded for free
from www.cpsc.gov. An additional resource is the American Society of Testing and Materials (ASTM)
Standard Consumer Safety Performance Specification for Home Playground Equipment (ASTM F1148)
which can be purchased and downloaded from www.astm.org.

4
TURBO TUBE SLIDE TOWER I STRUCTIO S
(1) 2'' x 4'' x 96''
47-1/2'' 47-1/2''
(1) 2'' x 4'' x 96''
47-1/2'' 25'' 12'' 7-3/8''
(1) 2'' x 4'' x 96''
32'' 23'' 23''
(
(1) 2'' x 4'' x 96''
18'' 18'' 18'' 11-1/4'' 8-1/4'' 8-1/4''
Sky Tower Turbo Cut List
Lumber Purchased Separately - (4) 2'' x 4'' x 8’
63-1/8''
48-1/4''
Minimum
Safety Zone
72''
64''

TURBO TUBE SLIDE TOWER I STRUCTIO S
Fig. 3
MODIFICATION: Install PF 3907 as shown
above.
Frame Construct on cont.
1. Ass mbl Fram 1 as shown in (F g. 3).
GAP
Frame 1
Frame 1 Construction
Use a 2’’ lag screw
to hold bracket in
place for later use.
Look for ‘’TOP’’
stamp on brackets
while installing.
TOP
GAPon
thisside
•WARNING•
Avoid splitting your
lumber by offsetting
your screws at least
/4’’ from edge.
2-1/2'' screw
Tailor’s Chalk
96-1/8''
[PF 3892] 1'' x 6'' x 47-1/2''
[PF 3907] 5/4'' x 6'' x 47-1/2''
Offset Arch
[PF 3886] 1'' x 4'' x 45-3/4''
1-3/4''
114-3/4''
(2)
2-1/2''
screws
(3)
2-1/2''
screws
per joint
(3)
2-1/2''
screws
per joint
(3)
2-1/2''
screws
TIMBERG OVE SEAM
5

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Install PF 3883 as shown n (F g. 8) above.
Install Deck Boards
1. Attach D ck Support Board as shown in (F g. 8).
2. Attach D ck Boards as shown in (F g. 8a).
Note: Scr ws at c nt r will attach to c nt r support.
2-1/2'' screw
(2)
2-1/2''
screws
per joint
(2)
2-1/2''
screws
per joint
Fig. 8 OTE: There must be a 1/8''
Nominal Gap between all
deck boards.
Fig. 8a
[PF 3883] 1'' x 4'' x 40-1/4''
(11) [PF 3902] 5/4'' x 4'' x 47-1/2''
BACK OF U IT
(View Rotated 90˚)
6

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Install front PF 3900 as shown n (F g. 9a). DO NOT nstall the
PF 3900 on the back of the deck, as shown n (F g. 9a).
Install Barr er Support Boards
1. Install Barri r Support Boards as shown in (F g. 9) and (F g. 9a).
2-1/2'' screw
Fig. 9
[PF 3903] 5/4'' x 4'' x 47-1/2''
(3)
2-1/2''
screws
per joint
[PF 3903] 5/4'' x 4'' x 47-1/2''
[PF 3900] 5/4'' x 4'' x 20-3/4''
[PF 3900] 5/4'' x 4'' x 20-3/4''
(3)
2-1/2''
screws
per joint
(5)
2-1/2''
screws
Fig. 9a
F USH
F USH
7

TURBO TUBE SLIDE TOWER I STRUCTIO S
2-1/2'' screw
MODIFICATION: DO NOT nstall the PF
3881 Barr er on the back of the deck, as
shown n (F g. 17). Th s barr er w ll be
nstalled later.
Barr er Boards
1. Install Barri r Boards as shown in (F g. 17) and
(F g. 17a).
Fig. 17a
(2)
1-1/2'' deck
screws
per joint
Fig. 17
(3) [PF 3881] 1'' x 4'' x 36''
OTE: There must be a 2''
Nominal Gap between
barrier boards.
1-1/2'' screw
(7) [PF 3881] 1'' x 4'' x 36''
Use 2-1/2'' screws to
secure 1'' x 4'' to 4'' x 4''
8

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Install barr er as shown n
(F g. 18).
Barr er Boards cont.
1. Install Barri r Boards as shown in (F g. 18).
1-1/2'' screw
OTE: There must be a 2-3/8''
Nominal Gap between all
barrier boards.
(3) [PF 3881] 1'' x 4'' x 36''
(2)
1-1/2'' screws
per joint
Fig. 18
9

TURBO TUBE SLIDE TOWER I STRUCTIO S
OTE: Upper screws are (2) 1-1/4''
ag Screws, ower screws are (3) 2''
ag Screws.
(2)
1-1/4'' ag
(3)
2'' ag
MODIFICATION: Sw tch PF 3904 and PF 3707
as shown n (F g. 20).
Frame 3 Attachment
1. Attach Fram Support Boards as shown in (F g. 20) and
(F g. 20a).
2. Attach Fram 3 to unit as shown in (F g. 20a) and (F g. 20b).
2-1/2'' screw
Fig. 20
Double check to make
sure boards are square
Fig. 20b
2'' Lag screw
1-1/4'' Lag Screw
Fig.20a
(3)
2'' lag screws
Per Bracket
(2)
1-1/4'' lag screws
Per Bracket
(3)
2-1/2'' screws
per joint
(3)
2-1/2'' screws
per joint
[PF 3707] 2'' x 4'' x 30''
[PF 3904] 5/4'' x 6'' x 30''
Center Arch
[PF 3402] 2'' x 4'' x 30''
[PF 3402] 2'' x 4'' x 30'' [PF 3879] 1'' x 4'' x 28-1/4''
[PF 3879] 1'' x 4'' x 28-1/4''
(3)
2-1/2''
screws
per joint
(2)
2-1/2''
screws
per joint
Frame 3
Frame 3
F USH
10

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Move PF 3880 to back of un t,
as shown n (F g. 22a).
Lower Deck cont.
1. Install Low r D ck Boards as shown in (F g. 22).
Note: Scr ws at c nt r will attach to c nt r support.
2. Install Barri r Support Board as shown in (F g. 22a).
Fig. 22
2-1/2'' screw
OTE: There must be a 1/4''
Nominal Gap between all
deck boards.
(2)
2-1/2''
screws
per joint
(3)
2-1/2''
screws
per joint
(6) [PF 3902] 5/4'' x 4'' x 47-1/2''
[PF 3880] 1'' x 4'' x 30''
Fig. 22a
11

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Move barr er to back of un t, as
shown n (F g. 23).
Lower Deck cont.
1. Install Barri r Boards as shown in (F g. 23) and (F g. 23a).
1-1/2'' screw
(2)
1-1/2''
screws
per joint
OTE: There must be a 1''
Nominal Gap between
barrier boards. (5) [PF 3879] 1'' x 4'' x 28-1/4''
Fig. 23
Fig. 23a
(2) [PF 3910] 5/4'' x 4'' x 28-1/4''
(2)
1-1/2''
screws
per joint
1'' GAP
12

TURBO TUBE SLIDE TOWER I STRUCTIO S
(3)
2-1/2''
screws
per joint
(4)
2'' screws
from Top of
Deck
Fig. 27c
1-1/2'' screw
MODIFICATION: Mount ladder to front of un t as
shown n (F g. 27c).
Ladder Assembly
1. Laminat Ladd r Uprights as shown in (F g. 27).
2. Install Ladd r Support Boards as shown in (F g. 27a).
3. Attach Ladd r Rungs as shown in (F g. 27b).
Pre-Dr ll Note: To pr v nt wood from splitting, pr -drill all hol s for th
Ladd r Rungs. Us a 1/8'' drill bit & drill to a maximum d pth of th
l ngth of th Lag Scr w us d.
4. Attach ladd r to tow r as shown in (F g. 27c).
1-1/4'' screw
2-1/2'' screw
2'' Lag screw
[PF 3875]
1'' x 4'' x 18-1/4''
[PF 3887]
1'' x 4'' x 46-1/4''
[PF 3875] 1'' x 4'' x 18-1/4''
[PF 3887] 1'' x 4'' x 46-1/4''
Fig. 27 Fig. 27a Fig. 27b
[PF 3908] 2'' x 4'' x 11-7/8''
[PF 3873] 1'' x 4'' x 14-1/8''
x2
5''
11-5/8''
11-5/8''
11-5/8''
11-5/8''
(16)
1-1/4'' screws
per side
(2)
1-1/2'' screws
per joint
(2)
2'' ag screws
per rung
2'' screw
(2) 2-1/2'' screws per joint
(5)
13-7/8''
ADDER RUNG
Pre-Drill
Perforaciones previas
F USH
A INEADO
13

TURBO TUBE SLIDE TOWER I STRUCTIO S
Fig. 32
(3)
1-1/4'' Lag Screws per bracket
9-1/2"
Fig. 32a
MODIFICATION: Install Monkey Bars on front of un t, as shown n (F g. 32a) and
(F g. 32b).
Monkey Bar Assembly Cont.
1. Attach th Monk y Bar Fram to th Monk y Bar Ladd r as shown in (F g. 32).
2. Dig (2) 8'' diam t r hol s, 16'' d p, at th locations shown in (F g. 32b).
3. Attach th Monk y Bar Ladd r to th unit as shown in (F g. 32a) and (F g. 32b).
Pre-Dr ll Note: To pr v nt wood from splitting, pr -drill th (6) hol s for th 1-1/4'' Lag Scr ws. Us a 1/8'' drill bit & drill to
a maximum d pth of 1-1/4''.
4. L v l th ass mbly, fill in hol s and compact arth around posts.
Fig. 32b
(3)
1-1/4'' Lag screws
per bracket
FLUSH
(3)
1-1/4'' Lag Screws
per bracket
1-1/4'' Lag screw
1-3/4''
24-1/2''
FLUSH
Pre-Drill
Perforaciones previas
74-5/8"
6'
16"
8'' Diameter
14

TURBO TUBE SLIDE TOWER I STRUCTIO S
MODIFICATION: Attach Decorat ve
Boards as shown n the f gures shown.
Decorat ve Assembl es
1. Install Window Sill Boards as shown in (F g. 37).
2. Plac th Nam Tag in a visibl ar a on on of th
uprights using (2) 1/2'' Pan H ad Scr ws as shown
in (F g. 37).
3. Install Window Chamf r Boards as shown
in (F g. 37a).
2'' screw
1-1/4'' screw
[PF 3882] 1'' x 4'' x 40-1/4''
(4)
2'' screws
[PF 3876] 1'' x 4'' x 22-3/4''
[PF 3882] 1'' x 4'' x 40-1/4''
(3)
2'' screws (4)
2'' screws
(3) [PF 3899] 5/4'' x 4'' x 9''
(2)
1-1/2''
screws
per board
Fig. 37
Fig. 37a
1-1/2'' screw
1/2'' Pan Head screw
THIS PRODUCT IS
INTENDED FOR USE
BY CHILDREN FROM
AGES 2-10 YEARS
For Home / Residential
Use ONLY
1212 Barberry Drive
Janesville, WI 53545
1-800-888-1232
www.swing-n-slide.com
R
15

TURBO TUBE SLIDE TOWER I STRUCTIO S
2'' screw 1-1/4'' screw
MODIFICATION: Attach Decorat ve Boards as shown n the f gures shown.
Decorat ve Assembl es Cont.
1. Install Chamf r Boards as shown in (F g. 38) and (F g. 38a).
2. Install Window S parators as shown in (F g. 38b) and (F g. 38c).
(4) [PF 3898] 5/4'' x 4'' x 3-1/2''
(2)
2'' screws
per board
(2) [PF 3898]
5/4'' x 4'' x 3-1/2''
(2)
2'' screws
per board
(2) [PF 3874] 1'' x 4'' x 18''
(2)
2'' screws
(2) [PF 3874] 1'' x 4'' x 18''
(4)
1-1/4''
screws
(4)
1-1/4''
screws
(2)
2'' screws
16-7/8''
16-7/8''
16-7/8''
16-7/8''
Fig. 38 Fig. 38a
Fig. 38b Fig. 38c
16

17
TURBO TUBE SLIDE TOWER I STRUCTIO S
Fig. 1
Sl de Barr er Construct on
1. Install slid and barri r support boards as shown
in (F g. 1), making c rtain th op ning b tw n
th m is 25''.
2. Install barri r as shown in (F g. 1a). Mak
c rtain slid op ning is 23''.
Fig. 1a
2-1/2'' screw
2'' x 4'' x 47-1/2''
23''
3-1/4'' Gap
Between Each
Barrier Board
2'' x 4'' x 32''
(4)
2''
screws
per barrier
board
2'' x 4'' x 47-1/2''
2'' x 4'' x 47-1/2''
92''
63-1/2''
31-1/2''
25''
(2) [PF 3881]1'' x 4'' x 36''
2'' screw
(3)
2-1/2''
screws
per board
(3)
2-1/2''
screws
per board

18
TURBO TUBE SLIDE TOWER I STRUCTIO S
2'' x 4'' x 12''
Fig. 2
I SIDE VIEW
U IT WAS ROTATED 180˚ FOR THIS VIEW
2'' x 4'' x 23''
(4)
2-1/2'' screws
per board
Fig. 2a
(4)
2-1/2'' screws
Sl de Barr er Cont.
1. Install (3) 2'' x 4'' Boards as shown in (F g. 2).
2. Install (2) 2'' x 4'' x 23'' Slid Support Boards on
th insid of your barri r as shown in (F g. 2a).
Turbo Tube Sl de: Ass mbl and attach Turbo Tub
Slid and Foot r as instruct d in th plan includ d
with your slid .
2-1/2'' screw
2'' x 4'' x 25''
2'' x 4'' x 23''
2'' x 4'' x 7-3/8''
(2)
2-1/2'' screws
(2)
2-1/2'' screws

19
TURBO TUBE SLIDE TOWER I STRUCTIO S
REFERE CE THE PLA PICTURED FOR SLIDE ASSEMBLY

© PlayCore Inc. 2012 Printed In USA A xxxx
Questions???...
Call our Customer Service Department
at 1-800-888-1232