Playcore BigToys Junior Synchro User manual

Issued/Revised:
SHEET 1 OF 4
4/14/15
MEC-130 SYNCHRO JR.
1-866-814-8697 bigtoys.com
Parts List
PART NUMBER
QTYDESCRIPTION
ITEM
24351CENTER POLE1
G441
1
PLAYPOD W/1.38" HOLE
2
G433GS148" FOOTING PIPE3
4046551
HUB/SPINDLE ASSY
4
4015852FINIAL 1
5
4046591
HARDWARE COMPLETE
4021391
PLAYPOD TO HUB ADAPTER
6
4015881
FINIAL SPACER 1
7
4021211
ANCHOR ROD
8173423
1/2" LOCKWASHER
8110623
1/2" x 1 1/4" B.H.C.S.
81144413/8" x 2" FLAT HEAD SOCKET CAP SCREW
8114425
3/8" x 1 1/2" FLAT HEAD SOCKET CAP SCREW
81746815/8" FLAT WASHER
8013011
BOLT, HEX 5/8-11 x 1 GRD 2 PLTD
81741023/8" FLAT WASHER
8110522
3/8" x 3/4" B.H.C.S.
80481113/8" COUPLER NUT
8155174
#8 x 3/4" WOOD SCREW
E402E1LABEL PACKAGE, 2-5 YEARS
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plan Views.
2. Attach Finials and Finial Spacer to top of Center Pole Assembly using 3/8" x 3/4" B.H.C.S., 3/8" Flatwashers, #8 x 3/4" Wood
Screws, and 3/8" Coupler Nut. See Detail A.
2. Attach Playpod to Center Pole using 3/8" x 1 1/2" Flat Head Cap Screws, 5/8" x 1" Hex Bolt, 5/8" Flatwasher and Hub Adapter.
See Detail B.
3. Attach Hub/Spindle Assembly to Center Pole Assembly using 3/8" x 1 1/4" B.H.C.S. See Detail C.
6. Insert Anchor Rod into Footing Pipe. Place footing Pipe into footing hole. Confirm that the Footing Pipe is plumb before filling
hole with concrete. Allow Concrete to cure at least 48 hours before use. Temporary bracing may be required until concrete cures.
7. Attach Synchro Spinner Assembly to Footing Pipe using 1/2" x 1 1/4" B.H.C.S. AND 1/2" Lockwasher. See Detail D.
8. Attach Warning Label and Age Appropriate Label on the outside of Footing Pipe as high as possible.
Note: Areas must be clean and dry before attaching Labels.

Issued/Revised:
SHEET 2 OF 4
4/14/15
MEC-130 SYNCHRO JR.
1-866-814-8697 bigtoys.com
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.
A
B
C
D
5
7
5
2
1
4
6
3
FINISHED ASSEMBLY

Issued/Revised:
SHEET 3 OF 4
4/14/15
MEC-130 SYNCHRO JR.
1-866-814-8697 bigtoys.com
3'-7 5/16" [109.94 cm]
2'-7 5/16" [79.46 cm]
MINIMUM
2'-6 3/16" [76.67 cm]
--- RESILIENT SURFACE ---
CONCRETE REQUIRED
.30 CUBIC YARDS
.23 [CUBIC METERS]
ELEVATION VIEW
PLAN VIEW
1'-2" [35.56 cm]
MAXIMUM
n2'-0" [60.96 cm]

Issued/Revised:
SHEET 4 OF 4
4/14/15
MEC-130 SYNCHRO JR.
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
A
3/8" x 3/4" B.H.C.S.
(811052)
3/8" COUPLER NUT
(804811)
#8 x 3/4" WOOD
SCREW (815517)
3/8" FLAT WASHER
(817410)
3/8" x 3/4" B.H.C.S.
(811052)
3/8" FLAT WASHER
(817410)
CENTER POST
FINIAL
FINIAL
SPACER
BOLT, HEX 5/8-11 x 1
GRD 2 PLTD (801301)
5/8" FLAT WASHER
(817468)
3/8" x 1 1/2" FLAT
HEAD SOCKET CAP
SCREW (811442)
PLAYPOD
HUB ADAPTER
CENTER POLE
B
3/8" x 1 1/2" FLAT
HEAD SOCKET CAP
SCREW (811442)
3/8" x 2" FLAT HEAD
SOCKET CAP
SCREW (811444)
3/8" x 1 1/2" FLAT
HEAD SOCKET CAP
SCREW (811442)
HUB/SPINDLE
ASSEMBLY
CENTER POLE
ASS'Y
CD
1/2" x 1 1/4" B.H.C.S.
(811062)
1/2" LOCKWASHER
(817342)
HUB/SPINDLE
ASSEMBLY
FOOTING PIPE