Playcore BigToys MBT-410 User manual

Issued/Revised:
SHEET 1 OF 5
3/7/14
MBT-410 SYNCHRO SPINNER
1-866-814-8697 bigtoys.com
Parts List
PART NUMBERQTYDESCRIPTIONITEM
G887P
1
CENTER POLE
1
G4411PLAYPOD W/1.38" HOLE2
EGA201
1
545 HUB / SPINDLE ASSY, SYNCHRO
3
G433GS148" FOOTING PIPE4
4015852FINIAL 15
4015862WOBBLY DISC6
4046601
HARDWARE COMPLETE
4015881FINIAL SPACER 1
7
8173423
1/2" LOCKWASHER
81106231/2" x 1 1/4" B.H.C.S.
24413
CAP SCREW, RED.HD 3/8 x 1-1/2 SOC FLT HD SS
80481113/8" COUPLER NUT
8110522
3/8" x 3/4" B.H.C.S.
81741023/8" FLAT WASHER
15982
DOWEL NUT, 1/4-20
04312SCREW, 1/4 X 2-1/2" SS - SPANNER HEAD
8155174
#8 x 3/4" WOOD SCREW
24425
CAP SCREW, 3/8 x 1-1/4 SOC FLT HD SS
4021211
ANCHOR ROD
E4021
DECAL PACKAGE, 5-12 YEARS
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
INSTALLATION INSTRUCTIONS:
1. Dig footing holes as shown in Elevation and Plan Views.
2. Attach Playpod to Center Pole using 3/8" x 1 1/2" Cap Screws. See Detail A.
3. Attach Wobbly Discs to pole using 1/4" x 2 1/2" Spanner Head Screw and Dowel Nut. See Detail B.
4. Attach Finials and Finial Spacer to top of Center Pole Assembly using 3/8" x 3/4" B.H.C.S., 3/8" Flatwashers, #8 x 3/4" Wood
Screws, and 3/8" Coupler Nut. See Detail C
5. Attach Hub/Spindle Assembly to Center Pole Assembly using 3/8" x 1 1/4" B.H.C.S. See Detail D.
6. Insert Anchor Rod into Footing Pipe. Place footing Pipe into footing hole. Confirm that the Footing Pipe is plumb before filling
hole with concrete. Allow Concrete to cure at least 48 hours before use. Temporary bracing may be required until concrete cures.
7. Attach Synchro Spinner Assembly to Footing Pipe using 1/2" x 1" B.H.C.S. AND 1/2" Lockwasher. See Detail E.
8. Attach Warning Label and Age Appropriate Label on the outside of Footing Pipe as high as possible.
Note: Areas must be clean and dry before attaching Labels.

Issued/Revised:
SHEET 2 OF 5
3/7/14
MBT-410 SYNCHRO SPINNER
1-866-814-8697 bigtoys.com
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.
FINISHED ASSEMBLY
A
B
C
D
E
1
5
7
6
2
4
3
1

Issued/Revised:
SHEET 3 OF 5
3/7/14
MBT-410 SYNCHRO SPINNER
1-866-814-8697 bigtoys.com
3'-4" [101.60 cm]
2'-4" [71.72 cm]
MINIMUM
ELEVATION VIEW
1'-5 7/16" [44.28 cm]
--- RESILIENT SURFACE ---
5'-4 3/16" [163.01 cm]
BRICK OR EQUIVALENT
n2'-0" [60.96 cm]
PLAN VIEW
CONCRETE REQUIRED
.27 CUBIC YARDS
.21 [CUBIC METERS]

Issued/Revised:
SHEET 4 OF 5
3/7/14
MBT-410 SYNCHRO SPINNER
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
SCREW, 1/4 X 2-1/2"
SS - SPANNER HEAD
(0431)
DOWEL NUT, 1/4-20
(1598)
WOBBLY DISC
CENTER POLE
B
CAP SCREW,
RED.HD 3/8 x 1-1/2
SOC FLT HD SS
(2441)
CENTER POLE
ASSEMBLY
PLAYPOD
A
3/8" x 3/4" B.H.C.S.
(811052)
3/8" FLAT WASHER
(817410)
#8 x 3/4" WOOD
SCREW (815517)
3/8" COUPLER NUT
(804811)
3/8" FLAT WASHER
(817410)
3/8" x 3/4" B.H.C.S.
(811052)
FINIAL
FINIAL SPACER
C
CAP SCREW, 3/8 x
1-1/4 SOC FLT HD SS
(2442) HUB/SPINDLE
ASSEMBLY
CENTER POST
ASSEMBLY
D

Issued/Revised:
SHEET 5 OF 5
3/7/14
MBT-410 SYNCHRO SPINNER
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
1/2" x 1 1/4" B.H.C.S.
(811062)
1/2" LOCKWASHER
(817342)
FOOTING PIPE
SYNCHRO SPINNER
ASSEMBLY
E