Playcraft Zig Zag Steel Net Wall 1968 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
ZIG ZAG STEEL NET WALL
Rev B
8/13/2010
1968
Page 1 of 3
NOTE: R5 Configuration shown.
R3.5 will vary slightly, but does
not affect the assembly.
Sections R5-09 Collars
See Installation Manual
Figure 1.1
FIGURE 1
Zig Zag Steel Net Wall R5
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for 09 Collars assembly instructions.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult your surfacing supply representative.

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
ZIG ZAG STEEL NET WALL
Rev B
8/13/2010
1968
Page 2 of 3
63
12
"
1613mm
13
14
"
337mm 13
14
"
337mm
12"
305mm
Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (2) Ø 12" footing holes. Refer to Footing Detail for
depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required.
Step 2
Locate collars at height shown in
Footing Detail. (See Note C)
** Height shown from finish grade
to top of collar.
* Footing depth must be adjusted to
compensate for the depth/thickness
requirements of selected safety surfacing.
See Section 06.1 of the Installation Manual
Installers Manual
Blocking, See
Footing Detail
Pea Gravel (for drainage)
Concrete Footing
Footing Anchor
2b Stone, drain rock
Undisturbed Soil
Optional Filter Fabric Over
LOOSE FILL GROUND COVER:
Impact attenuating (resilient) surfacing
9" compacted or 12" uncompressed depth
Compacted depth shown. (See Note D)
18"
457mm
27" *
686mm
85" **
2159mm
R3.5 Top View - Footing Layout
(Top of Soil)
(Finish Grade)
R5 Top View - Footing Layout
12
116
"
307mm 59
78
"
1521mm 12
116
"
307mm

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
ZIG ZAG STEEL NET WALL
Rev B
8/13/2010
1968
Page 3 of 3
R5 Parts List Specifications
ZIG ZAG STEEL NET WALL:
Shall be fabricated from 2.375" O.D. 11 gauge
steel outer frame welded to 1.315" O.D. 11 gauge
steel rungs. 1/4" steel clevises will be welded to
frame. Zig Zag Steel Net Wall will have a multi-stage
baked-on powder coat finish.
MOUNTING BLOCKS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy. The Mounting Blocks have
a multi-stage baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
R3.5 Parts List
Part #
DESCRIPTION
QTY.
FS-1968-R5 Zig Zag Steel Net Wall 90 R5 1
GF-7006-B Mounting Block R5 Bottom 2
GF-7006-T Mounting Block R5 Top 2
9143112-TR Bolt Shoulder 3/8" x 2-1/2" BH 2
9281062-5-TR Screw Soc HD CS 1/4" x 1-3/8" TR 2
9345002 Washer Flat SAE 1/2" 4
9443092-TR Nut Barrel 3/8" x 2" BH 2
Part #
DESCRIPTION
QTY.
FS-1968-R35 Zig Zag Steel Net Wall 84 R3.5 1
GG-8110 Mounting Block 4 Top R3.5 2
GG-8111 Mounting Block 4 Bottom R3.5 2
9143112-TR Bolt Shoulder 3/8" x 2-1/2" BH 2
9281062-5-TR Screw Soc HD CS 1/4" x 1-3/8" TR 2
9345002 Washer Flat SAE 1/2" 4
9443092-TR Nut Barrel 3/8" x 2" BH 2
Step 3
Insert legs into footing holes and attach Zig Zag
Steel Net Wall to collars as shown in Figure 1.1.
(See Note A)
Figure 1.1
Step 4
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE" section
of the Installation Manual.
Step 5
Plumb and level entire component. Pour concrete into
footing hole. Allow at least 72 hours to cure before
using this equipment. (See Note B)
Step 6
Place appropriate compliant protective surfacing under
and around Zig Zag Steel Net Wall. (See Note D)
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
BLOCK
BOTTOM
Shoulder Bolt
3/8" x 2-1/2"
Washer
1/2" SAE
Washer
1/2" SAE
Barrel Nut
3/8" x 2"
WALL
STEEL NET
BLOCK TOP
MOUNTING
ZIG ZAG
MOUNTING
1/4" x 1-3/8" TR
Socket Head Screw