Playcraft Trans-Glide 1975 Programming manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 1 of 19
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height of
the equipment or consult your surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Concrete must be allowed to cure completely before installing the equipment (at least 72 hours).
(C) Refer to Installation Manual for R5-09 Collars and R5-11 Socket Clamps installation instructions.
(D) Follow the installation procedure for expansion anchors (min. 1/2" x 5-1/2") as provided by the manufacturer.
Expansion anchors and hardware are not included with assembly.
(E) Important: Gap between Trans-Glide Deck and Transition Deck must be between 1-1/8" [29mm] to 1-1/4"
[32mm]. The top of Trans-Glide Deck to top of Transition Deck must be flush 1/4" [6mm].
(F) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
FIGURE 1
Trans-Glide
See Footing Detail
and R5-11 Clamps
See Installation Manual
Sections R5-09 Collars
Figure 1.1

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 2 of 19
30
516
"
770mm
11
1316
"
300mm
51
14
"
1302mm
86
58
"
2200mm
Concrete Footing
2b Stone, drain rock
Undisturbed Soil
LOOSE FILL SURFACING MATERIAL SHOWN:
9" compressed or 12" uncompressed depth.
Compressed depth shown. (See Note F)
Deck Gap
(Finish Grade)
(Top of Soil)
6
58
"
168mm **
24"
610mm
15"
381mm *
Footing Detail
Step 1
Refer to Footing Layout and mark footing hole
location. Dig (1) 86-5/8" x 51-1/4" footing hole.
Refer to Footing Detail for depth and details.
Pour concrete into footing hole. (See Note B)
IMPORTANT: For areas with soft soil
conditions, larger footings may be required.
* Footing depth must be adjusted to
compensate for the depth/thickness
requirements of selected safety surfacing.
See Section 06.1 of the Installation Manual.
** Height shown from top of deck to top of
collar.
Top View - Footing Layout
Driver Side
Passenger Side
Decks flush
1/4" [6mm]
(See Note E)
Detail View - Deck Gap
1-1/8" to 1-1/4"
(See Note E)

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 3 of 19
FIGURE 5
3/8" Lock Nut
3/8" x 7/8" O.D.
Washer
3/8" x 7/8" O.D.
Washer
3/8" x 1-1/4"
Button Head Bolt
WHEEL HUB
STIFFENER
WHEEL HUB
Step 6
(Factory Assembled)
Attach Wheel Hub Stiffeners to Wheel Hubs as shown
in Figure 5. (See Note A)
Step 4
(Factory Assembled)
Attach Trans-Glide Decks together as shown
in Figure 3. (See Note A)
Step 5
(Factory Assembled)
Attach Trans-Glide Decks to Wheel Hubs and
Stiffeners as shown in Figure 4. (See Note A)
Step 3
(Factory Assembled)
Press Sealed Ball Bearings into Track Wheels
and attach to Wheel Hubs as shown in Figure 2.
EXTERNAL
SNAP RING
1" X 1-1/2" O.D.
Shim
SEALED BALL
BEARING
TRACK WHEEL
SEALED BALL
BEARING
WHEEL HUB
FIGURE 2
FIGURE 3
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
TRANS-GLIDE
DECK
TRANS-GLIDE
DECK
FIGURE 4
3/8" x 1" O.D.
Washer
3/8" x 1-1/4"
Hex Bolt TRANS-GLIDE
DECK
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
WHEEL HUB
STIFFENER
WHEEL HUB

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 4 of 19
Step 7
(Factory Assembled)
Install Nutserts to Trans-Glide Base as shown
in Figure 6. (See Note A)
Step 8
(Factory Assembled)
Slide Trans-Glide Deck into Base and attach Bumpers
to Trans-Glide Base as shown in Figure 7. (See Note A)
Step 9
(Factory Assembled)
Attach Torsion Spring, Caps and Arm to Torsion Bracket
as shown in Figure 8. (See Note A)
FIGURE 6
TRANS-GLIDE
BASE
3/8" Nutsert
FIGURE 7
3/8" Lock
Nut
3/8" x 1" O.D.
Washer
BUMPER
3/8" x 1" O.D.
Washer
3/8" x 2-1/2"
Button Head Bolt
TRANS-GLIDE
BASE
TRANS-GLIDE
DECK
RETAINER PLATE
FIGURE 8
1/2" x 1" Button
Head Bolt
1/2" SAE
Washer
TORSION
SPRING CAP
TORSION
SPRING
TORSION
ARM
3/8" x 5/8" Socket
Set Screw
TORSION
SPRING CAP 1/2" x 1" Button
Head Bolt
1/2" SAE
Washer
TORSION
BRACKET

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 5 of 19
Step 11
(Factory Assembled)
Attach Dampener Plate to Dampener Bracket
as shown in Figure 10. (See Note A)
Step 12
(Factory Assembled)
Insert Torsion Arm into Dampener Plate and attach
Dampener Bracket to Trans-Glide Base as shown
in Figure 11. (See Note A)
Step 10
(Factory Assembled)
Attach Torsion Bracket to Passenger Side Wheel
Hub as shown in Figure 9. (See Note A)
FIGURE 10
3/8" x 7/8" O.D.
Washer
3/8" Lock Nut DAMPENER
PLATE
DAMPENER
BRACKET
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
FIGURE 11
3/8" x 1" O.D.
Washer
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
DAMPENER BRACKET
TORSION ARM
TRANS-GLIDE
BASE
FIGURE 9
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
TORSION BRACKET
WHEEL HUB

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 6 of 19
FIGURE 13
3/8" x 3/4"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
HANDLE GUARD
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
DRIVE HOUSE
2" x 3/4"L
Flanged Bearing
2" x 3/4"L
Flanged Bearing
Step 13
(Factory Assembled)
Assemble Grips to Trans-Glide Handle and attach
to Driveshaft as shown in Figure 12. (See Note A)
Step 14
(Factory Assembled)
Press Bearings into Drive House and attach Handle
Guard as shown in Figure 13. (See Note A)
Step 15
(Factory Assembled)
Press Bearings into Drive Arm, Drive Plate, and
Driveshaft Bracket as shown in Figure 14.
FIGURE 12
3/8" x 2"
Barrel Nut
1/2" SAE
Washer
TAICHI SPINNER
CAP
TAI CHI SPINNER
GRIP
TAICHI SPINNER
BUSHING
TAICHI SPINNER
SPACER
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
DRIVESHAFT
3/8" x 1-1/4"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
TRANS-GLIDE
HANDLE
BEARING
DRIVE ARM
FIGURE 14
DRIVE PLATE
BEARING
BEARING
DRIVESHAFT
BRACKET

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 7 of 19
Step 16
(Factory Assembled)
Attach Back Accents to Back Side Panels as shown
in Figure 15. (See Note A)
NOTE: Back Right Side Panel shown.
Step 17
(Factory Assembled)
Attach Back Handles and Guards to Back Side Panels
as shown in Figure 16. (See Note A)
NOTE: Back Right Side Panel shown.
Step 18
(Factory Assembled)
Attach Front Accents to Front Side Panels as shown
in Figure 17. (See Note A)
NOTE: Front Right Side Panel shown.
FIGURE 17
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut FRONT ACCENT
FRONT SIDE
PANEL
FIGURE 16
BACK GUARD
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
BACK HANDLE
BACK SIDE
PANEL
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
FIGURE 15
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
1/2" SAE Washer
3/8" x 5/8" Barrel Nut
BACK ACCENT
BACK SIDE
PANEL

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 8 of 19
FIGURE 19
3/8" x 1-3/8"
Shoulder Bolt
1/2" SAE
Washer
DOOR TRIM
DOOR PANEL
DOOR TRIM
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
Step 19
(Factory Assembled)
Attach Front Handles and Guards to Front Side Panels
as shown in Figure 18. (See Note A)
NOTE: Front Right Side Panel shown.
Step 20
(Factory Assembled)
Attach Door Trim to Door Panel as shown in Figure 19.
(See Note A)
Step 21
(Factory Assembled)
Attach Skirt Panels to Skirts as shown in Figure 20.
(See Note A)
FIGURE 18
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
FRONT GUARD
FRONT HANDLE
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
FIGURE 20
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 7/8" O.D.
Washer
3/8" x 3/4"
Button Head Bolt
SKIRT PANEL SKIRT

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 9 of 19
FIGURE 22
DRIVESHAFT
BRACKET
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
TRANS-GLIDE
BASE
Step 23
(Factory Assembled)
Attach Driveshaft Bracket to Trans-Glide Base as
shown in Figure 22. (See Note A)
Step 22
(Factory Assembled)
Insert Driveshaft into Drive House and attach Snap Ring.
Attach Drive Plate to Driveshaft as shown in Figure 21.
(See Note A)
Step 24
Attach Drive House to Trans-Glide Decks as shown
in Figure 23. (See Note A)
Step 25
Attach Drive Arm to Drive Plate and Driveshaft
Bracket as shown in Figure 24. (See Note A)
FIGURE 21
DRIVE PLATE
1/2" x 1" Button
Head Bolt
9/16" X 2-1/8" O.D.
WASHER
DRIVESHAFT
SNAP RING
FIGURE 23
DRIVESHAFT
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" Lock Nut
3/8" x 1" O.D.
Washer
TRANS-GLIDE
DECK
DRIVE HOUSE
FIGURE 24
3/8" x 1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
DRIVE ARM
PINION ROD
1-3/8 x 5/8" THICK
NYLON WASHER
3/8" x 7/8" O.D.
Washer
3/8" x 1/2"
Button Head Bolt
DRIVE PLATE

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 10 of 19
FIGURE 26
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
TRANS-GLIDE
TRANSITION DECK
FIGURE 27
3/8" Lock Nut
3/8" x 1" O.D.
Washer
SIGN
TRANS-GLIDE
TRANSITION DECK
3/8" x 1" O.D.
Washer
3/8" x 1-3/4"
Button Head Bolt
Step 29
Attach Signs to Trans-Glide Transition Deck as
shown in Figure 27. (See Note A)
Step 27
Locate and attach collars to posts at heights shown
in Footing Detail. Attach Trans-Glide Transition Deck
to collars as shown in Figure 1.1. (See Notes A & C)
Step 26
Attach Trans-Glide Transition Deck to collars as shown
in Figure 25. (See Note A)
Step 28
Attach Trans-Glide Transition Deck to deck
as shown in Figure 26. (See Note A)
Figure 1.1
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
MOUNTING INSERT
FIGURE 25
3/8" x 2-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
TRANS-GLIDE
TRANSITION DECK
MOUNTING BLOCK
TOP
3/8" x 2"
Barrel Nut
1/2" SAE
Washer
MOUNTING BLOCK
BOTTOM

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 11 of 19
FIGURE 29
3/8" x 3/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
SPRING RIDER
BRACKET
HALF WALL
HALF WALL
FIGURE 30
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
TRANS-GLIDE
DECK
FIGURE 28
TRANS-GLIDE
BASE
BASE CAP
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
Step 30
Attach Base Caps to Trans-Glide Base as shown
in Figure 28.
NOTE: Do not use liquid thread lock.
(such as Loctite
®
)
Step 31
Attach Spring Rider Brackets to Half Walls
as shown in Figure 29. (See Note A)
Step 32
Attach Half Walls to Trans-Glide Decks
as shown in Figure 30. (See Note A)

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 12 of 19
FIGURE 31
3/8" Lock Nut3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" x 1-3/4"
Button Head Bolt
FRONT SIDE
PANEL
DECK SPACER
BACK SIDE
PANEL
TRANS-GLIDE
DECK
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 7/8" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
Step 33
Attach Back and Front Side Panels and Deck Spacer
to Trans-Glide Deck as shown in Figure 31.
(See Note A)
Step 34
Attach Back and Front Side Panels to Half Walls
as shown in Figure 32. (See Note A)
Step 35
Attach Back and Front Side Trim to Panels
and Trans-Glide Deck as shown in Figure 33.
(See Note A)
FIGURE 33
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
FRONT DECK
TRIM
FRONT SIDE
PANEL
TRANS-GLIDE
DECK
DECK SPACER
BACK SIDE PANEL
BACK DECK
TRIM
FIGURE 32
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 1" O.D.
Washer
3/8" x 3/4"
Button Head Bolt
FRONT SIDE
PANEL
BACK SIDE
PANEL
HALF WALL

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 13 of 19
Step 36
Attach Back and Front Side Panels and Door
to Trans-Glide Deck as shown in Figure 34.
(See Note A)
Step 37
Attach Back and Front Side Panels to Half Walls
as shown in Figure 35. (See Note A)
Step 38
Attach Door Braces to Door, Back, and Front Panels
as shown in Figure 36. (See Note A)
FIGURE 34
3/8" x 1-3/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
TRANS-GLIDE
DECK 3/8" x 2-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
FRONT SIDE
PANEL
DOOR FRAME
DOOR PANEL
BACK SIDE
PANEL
FIGURE 35
3/8" x 1" O.D.
Washer
3/8" x 3/4"
Button Head Bolt
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
FRONT SIDE
PANEL
BACK SIDE
PANEL
HALF WALL
FIGURE 36
3/8" x 1-3/4"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
FRONT SIDE
PANEL
DOOR BRACE
DOOR PANEL
BACK SIDE
PANEL

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 14 of 19
Step 39
Attach Back and Front Deck Trim to Panels
and Trans-Glide Deck as shown in Figure 37.
(See Note A)
Step 40
Attach Spring Rider Brackets to Deck Trim
and Deck Trim to Trans-Glide Deck as shown
in Figure 38. (See Note A)
Step 41
Attach Bench Backs to Bench Seats as shown
in Figure 39. (See Note A)
FIGURE 38
3/8" x 2-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" Lock Nut
3/8" x 1" O.D.
Washer
TRANS-GLIDE
DECK
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
SPRING RIDER
BRACKET
3/8" x 1" O.D.
Washer
3/8" x 1-3/4"
Button Head Bolt
FIGURE 39
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer 3/8" Lock Nut
3/8" x 1" O.D.
Washer
BENCH SEAT
BENCH BACK
FIGURE 37
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut FRONT DECK
TRIM
BACK DECK
TRIM
BACK SIDE
PANEL
DOOR PANEL
FRONT SIDE
PANEL
TRANS-GLIDE
DECK

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 15 of 19
FIGURE 42
3/8" x 3/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
SEAT PANEL
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
SPRING RIDER
BRACKET
Step 42
Attach Bench Backs and Seats to Side Panels
as shown in Figure 40. (See Note A)
Step 43
Attach Bench Rails to Bench Backs and Side
Panels as shown in Figure 41. (See Note A)
Step 44
Attach Spring Rider Brackets to Seat Panels
as shown in Figure 42. (See Note A)
FIGURE 41
3/8" x 1-3/4"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
1/2" SAE
Washer
3/8" x 5/8"
Barrel Nut
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
BENCH RAIL
BENCH BACK
FIGURE 40
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 1" O.D.
Washer
3/8" x 1-3/4"
Button Head Bolt
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 1" Button
Head Bolt
3/8" x 1" O.D.
Washer
BENCH BACK
BENCH SEAT

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 16 of 19
FIGURE 45
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" x 1" Button
Head Bolt
3/8" x 2" Button
Head Bolt
3/8" x 1" O.D.
Washer
SKIRT
3/8" x 1-1/4"
Button Head Bolt
Step 45
Attach Seat Panels to Bench Backs and Side Panels
as shown in Figure 43. (See Note A)
Step 46
Using the Trans-Glide Base as a template locate
and mark anchor hole locations. Install Expansion
Anchors. (See Notes B, D & E)
IMPORTANT: Refer to Detail View Deck Gap and
Top View Footing Layout.
Step 47
Attach Trans-Glide Assembly to Expansion
Anchors. (See Notes B, D & E)
WARNING: The Required gap must be varified
prior to using. Refer to Detail View Deck Gap and
Top View Footing Layout.
Step 48
Attach Skirts to Side Panels as shown in Figure 44.
NOTE: Do not use liquid thread lock.
(such as Loctite
®
)
Step 49
Attach Skirts to Trans-Glide Decks and Side Panels
as shown in Figure 45.
NOTE: Do not use liquid thread lock.
(such as Loctite
®
)
Step 50
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
WARNING: The Required gap must be varified
prior to using. Refer to Detail View Deck Gap and
Top View Footing Layout.
Step 51
Place required protective surfacing under and
around Trans-Glide Assembly. (See Note F)
FIGURE 44
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" Lock Nut
SKIRT
FIGURE 43
3/8" x 5/8"
Barrel Nut
1/2" SAE
Washer
3/8" x 1" Button Head Bolt
3/8" x 1" O.D. Washer
BENCH BACK
SEAT PANEL
3/8" x 1-1/2"
Button Head Bolt
3/8" x 7/8" O.D.
Washer
1/2" SAE Washer
3/8" x 5/8"
Barrel Nut

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 17 of 19
Part # DESCRIPTION QTY
AE-0425 Trans-Glide Drive Plate 1
AE-0426 Trans-Glide Drive Arm 1
AE-0452 2" x 3-1/2" Retainer Plate 4
AE-0453 2-1/8" Dia. Pipe Plug - 9/16" Hole 1
BE-0418 Trans-Glide Wheel Hub Stiffener 4
BE-0419 Trans-Glide Torsion Bracket 1
BE-0420 Trans-Glide Dampener Bracket 1
CE-0445 Trans-Glide Bench Skirt 2
CE-0447-L Trans-Glide Left Deck 1
CE-0447-R Trans-Glide Right Deck 1
ED-0013-KB Tai Chi Spinner Knob Bushing 2
ED-0013-KC Tai Chi Spinner Knob Cap 2
ED-0013-KG Tai Chi Spinner Knob Grip 2
ED-0013-KS Tai Chi Spinner Knob Spacer 2
EE-0145 Square Torsion Spring Cap 2
EE-0235-BSP Trans-Glide Back Side Panel 2
EE-0235-DOOR Trans-Glide Door Panel 1
EE-0235-FSP Trans-Glide Front Side Panel 2
EE-0236-BGL Trans-Glide Back Guard Left 1
EE-0236-BGR Trans-Glide Back Guard Right 1
EE-0236-BHL Trans-Glide Back Handle Left 1
EE-0236-BHR Trans-Glide Back Handle Right 1
EE-0236-DT Trans-Glide Door Trim 2
EE-0236-FGL Trans-Glide Front Guard Left 1
EE-0236-FGR Trans-Glide Front Guard Right 1
EE-0236-FHL Trans-Glide Front Handle Left 1
EE-0236-FHR Trans-Glide Front Handle Right 1
EE-0236-SKT Trans-Glide Skirt Panel 2
EE-0237-BLA Trans-Glide Back Left Accent 1
EE-0237-BRA Trans-Glide Back Right Accent 1
EE-0237-FLA Trans-Glide Front Left Accent 1
EE-0237-FRA Trans-Glide Front Right Accent 1
EE-0238 Trans-Glide Handle Guard 1
EE-0239 Trans-Glide Handle 1
FS-1975-ARM Trans-Glide Torsion Arm 1
FS-1975-BASE Trans-Glide Base 1
FS-1975-DRV Trans-Glide Driveshaft 1
FS-1975-DSB Trans-Glide Driveshaft Bracket 1
FS-1975-HSE Trans-Glide Drive House 1
FS-1975-HUB Trans-Glide Wheel Hub 2
HE-0004 50 x 120 Torsion Spring 1
HE-0043 Trans-Glide Bumper 4
IE-0033 Trans-Glide Track Wheel 6
EE-0256 Trans-Glide Dampener Plate 1
455111 Nutsert 3/8 x .805 16
480314 Shim 1" X 1-1/2" O.D. 6
480320 External Snap Ring 1
481100-2 2" O.D. x 9/16" Double-Sealed Ball Bearing 1" I.D. 12
482100 1" I.D. External Snap Ring 6
561212 1/2" x 1/2"L Flanged Bearing 4
Part # DESCRIPTION QTY
561234 2" x 3/4"L Flanged Bearing 2
9103032-TR Bolt Button Head 3/8" x 3/4" 24
9103062-TR Bolt Button Head 3/8" x 1-1/4" 28
9103072-TR Bolt Button Head 3/8" x 1-1/2" 76
9103112-TR Bolt Button Head 3/8" x 2-1/2" 8
9105052 Bolt Button Head 1/2" x 1" 9
9123062 Bolt Hex 3/8 x 1-1/4" 8
9143062-TR Bolt Shoulder 3/8" x 1-3/8" BH 4
9263022 Screw Soc Set 3/8" x 5/8" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 74
9333042 Washer Flat 3/8" x 7/8" O.D. 122
9345002 Washer Flat SAE 1/2" 100
9413002 Nut Lock 3/8" 52
9443022-TR Nut Barrel 3/8" x 5/8" BH 86
9443092-TR Nut Barrel 3/8" x 2" BH 2
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
Assembled Parts List

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 18 of 19
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
Part # DESCRIPTION QTY
BE-4466 Spring Rider Bracket 28
CE-0444-B Trans-Glide Bench - Back 2
CE-0444-S Trans-Glide Bench - Seat 2
CF-0446 Trans-Glide Transition Deck R5 1
EE-0235-HW Trans-Glide Half Wall 4
EE-0235-SPC Trans-Glide Deck Spacer 1
EE-0236-BDT Trans-Glide Back Deck Trim 2
EE-0236-DBL Trans-Glide Door Brace Left 1
EE-0236-DBR Trans-Glide Door Brace Right 1
EE-0236-DFM Trans-Glide Door Frame 1
EE-0236-FDT Trans-Glide Front Deck Trim 2
EE-0236-SEAT Trans-Glide Seat Panel 2
EE-0240 Trans-Glide Base Cap 2
EE-0251-L Trans-Glide Sign - Left 1
EE-0251-R Trans-Glide Sign - Right 1
FS-1975-BRL Trans-Glide Bench Rail 2
GE-7015 Mounting Insert 2
GF-7006-B Mounting Block R5 Bottom 2
GF-7006-T Mounting Block R5 Top 2
HS-1001-R5 Socket Clamp Set R5 2
IE-0038 Trans-Glide Pinion Rod 2
9103012-TR Bolt Button Head 3/8" x 1/2" 4
9103032-TR Bolt Button Head 3/8" x 3/4" 36
9103052-TR Bolt Button Head 3/8" x 1" 12
9103062-TR Bolt Button Head 3/8" x 1-1/4" 38
9103072-TR Bolt Button Head 3/8" x 1-1/2" 64
9103082-TR Bolt Button Head 3/8" x 1-3/4" 41
9103092-TR Bolt Button Head 3/8" x 2" 4
9103102-TR Bolt Button Head 3/8" x 2-1/4" 5
9103112-TR Bolt Button Head 3/8" x 2-1/2" 6
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 266
9333042 Washer Flat 3/8" x 7/8" O.D. 30
9345002 Washer Flat SAE 1/2" 102
9367055 1.07" x .645" x .065" Nylon Washer 2
9413002 Nut Lock 3/8" 86
9443022-TR Nut Barrel 3/8" x 5/8" BH 100
9443092-TR Nut Barrel 3/8" x 2" BH 2
RETAINER PLATE:
Shall be precision cut from 1/4" thick steel. The
Retainer Plate shall have a multi-stage baked-on
powder coat finish.
SPRING RIDER BRACKET:
Shall be precision cut and formed from 3/16" thick
steel. The Spring Rider Bracket shall have a multi-
stage baked-on powder coat finish.
TRANS-GLIDE BASE:
Shall be precision cut and welded from 1/4" thick
steel with welded 1.900" 11 gauge steel stiffeners.
The Trans-Glide Base shall have a multi-stage
baked-on powder coat finish.
TRANS-GLIDE BENCH BACK & SEAT:
Shall be punched, formed and welded from 14
gauge sheet steel with 12 gauge steel gussets and
end caps. The Trans-Glide Bench Back and Seat
shall be Play-Tuff™ coated after fabrication.
TRANS-GLIDE BENCH RAIL:
Shall be fabricated using 1.660" O.D. 11 gauge
steel tubing with welded 1.315" O.D. 12 gauge steel
handle and 1/4" thick steel mounting tabs. The
Trans-Glide Bench Rail shall have a multi-stage
baked-on powder coat finish.
TRANS-GLIDE BENCH SKIRT:
Shall be punched, formed and welded from 10
gauge sheet steel. The Trans-Glide Bench Skirt
shall have a multi-stage baked-on powder coat
finish.
TRANS-GLIDE BUMPER:
Shall be 3/8" thick, 3-ply rubber belt.
TRANS-GLIDE DAMPENER & TORSION
BRACKET:
Shall be precision cut and formed from 3/8" thick
steel. The Trans-Glide Dampener and Torsion
Bracket shall have a multi-stage baked-on powder
coat finish.
TRANS-GLIDE DECK & TRANSITION DECK:
Shall be punched formed and welded from 12
gauge sheet steel. The Trans-Glide Deck and
Transition Deck shall be Play-Tuff™ coated after
fabrication.

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
TRANS-GLIDE ASSEMBLY
INSTALLATION INSTRUCTIONS
Rev B
10/13/2016
1975
Page 19 of 19
TRANS-GLIDE DAMPENER PLATE:
Shall be made from Ultra High Molecular Weight
Polyethylene for lasting durability.
TRANS-GLIDE DRIVE ARM & DRIVE PLATE:
The Trans-Glide Drive Arm and Drive Plate shall be
precision cut from 1/2" thick steel. The Trans-Glide
Drive Arm and Drive Plate shall have a multi-stage
baked-on powder coat finish.
TRANS-GLIDE DRIVESHAFT:
Shall be fabricated using 1.660" O.D. 11 gauge
steel tubing with welded machined steel spindles
and 1/4" thick steel mounting plate.The Trans-Glide
Driveshaft shall have a multi-stage baked-on
powder coat finish.
TRANS-GLIDE DRIVESHAFT BRACKET:
Shall be fabricated using precision cut and welded
1/2" thick steel tabs. The Trans-Glide Driveshaft
Bracket shall have a multi-stage baked-on powder
coat finish.
TRANS-GLIDE HANDLE:
Shall be made from high density 1" sheet plastic
specially formulated for optimum UV stability and
color retention.
TRANS-GLIDE DRIVE HOUSE:
Shall be fabricated using 3.5" O.D. 11 gauge steel
tubing with welded 10 gauge steel gussets and 1/4"
thick steel mounting plates. The Trans-Glide Drive
House shall have a multi-stage baked-on powder
coat finish.
TRANS-GLIDE PANEL SET:
Shall be made from high density 3/4" sheet plastic
specially formulated for optimum UV stability and
color retention.
TRANS-GLIDE TORSION ARM:
Shall be fabricated using 3-1/2" square 3/16" thick
wall tubing with welded 1/4" thick steel gussets and
1-1/4" square 1/8" thick wall tubing arm. The Trans-
Glide Torsion Arm shall have a multi-stage baked-
on powder coat finish.
TRANS-GLIDE TRACK WHEEL:
Shall be machined Nylon 6/6.
TRANS-GLIDE WHEEL HUB:
Shall be fabricated using precision cut and formed
3/8" thick steel and machined stainless steel axles.
TRANS-GLIDE WHEEL HUB STIFFENER:
Shall be punched, formed, and welded from 10
gauge sheet steel. The Trans-Glide Wheel Hub
Stiffener shall be Play-Tuff™ coated after
fabrication.
MOUNTING BLOCKS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy. The Mounting Blocks have
a multi-stage baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance