PLAYNETIC KineticSeesaw User manual

KineticSeesaw
User Manual
SS90018_19022020
Loohorst 3 | 7207 BL Zutphen | The Netherlands
[email protected] | www.playnetic.nl | [phone]

Loohorst 3 | 7207 BL Zutphen | The Netherlands
[email protected] | www.playnetic.nl | [phone]
Install the Product
Overview Product
Control the Volume
Change the Content
Maintenance
Check Interactive Elements
Play and Test
Install and Manage a Timelock
3
3
4
5
8 8
3
4
7
Reset the LED
2

Install the Product
Install the product according to the Playnetic Installation Manual.
During the installation, make sure that the potential users can not
be exposed to hazards / dangerous situations. Check the stability
of the product.
Overview Product
The overview above shows where all important parts can be
found.
Check Interactive Elements
Use the product and generate energy. If applicable, check that the
interactive elements such as the music, lights, smell, electronic- and
mechanical parts are working properly.
Number of Users
Playnetic recommends you to use the product with a maximum of
two users.
3
Service hatch
Energy box
LED lineSeat
Shock absorber
Handle

Control the Volume
1. Remove the bolts with the supplied hex key.
2. Remove the service hatch.
3. Generate energy with the product.
4. Adjust the volume.
5. Close the service hatch.
Play and Test
1. Generate energy with the product.
2. Test if the correct MP3 files are played.
3. Test if the LED line runs in the correct direction on the beam.
*Are the tests incorrect? Then change the content and reset
the LED. Follow the instructions in the Playnetic User Manual.
4
Volume

Change the Content
1. Get a USB stick. Make sure that you meet the following requirements:
a. Only use MP3-files.
b. The name of the MP3 file needs to have at least 5 characters.
c. The name of the MP3 file can’t contain any strange characters.
d. A single MP3 file can not be bigger than 2 MB.
2. Use the supplied hex key and unscrew the bolts.
3. Remove the service hatch.
5
D
E
Read more
USB port

6
Change the Content
4. Put the USB stick into the computer.
5. Generate energy with the product. Wait until the update is
completed. Remove the USB stick after completion.
6. Make sure that you put the dust cover back over the USB port.
7. Close the service hatch.
“In progress, please wait...”
“Downloading data
completed, remove USB
device”
USB port

7
“In progress, please wait...”
“Downloading data
completed, remove USB
device”
Receive Timelock
1. Receive a USB device. Playnetic has set the
correct start- and endtime for you.
Install and Manage a Timelock
1. Remove the bolts with the supplied hex key.
2. Remove the service hatch.
3. Important! The timelock must be installed at 12
o’clock local time. If the installation is being done too
late or too early, the timelock will not work properly.
4. Put the USB stick into the computer.
5. Generate energy. Wait until the update is completed.
Remove the USB stick after completion.
6. Make sure that you put the dust cover back over the
USB port.
7. Close the service hatch.
Update Your Timelock 2x a Year
For updating your timelock, use the USB device you
received from Playnetic with the correct start- and
endtime (same USB device for install option). Repeat
step 1 till 7 in ‘install a timelock’ to complete the update.

LED
1. Remove the bolts with the supplied hex key.
2. Remove the service hatch.
3. Make sure there is a good view of the LED switch
Reset the LED
When do you use the LED switch?
You almost never have to use this switch because Playnetic always
programs the LED-line correctly before the product leaves our factory. But
sometimes it might happen that you have to recalibrate the LED-line. For
example when the ground on location has a raised surface. To do this you
can use the LED switch.
8
Maintenance
The product must be maintained according to the Playnetic
Maintenance Advice.
Read more

LED
4. Generate a lot energy (+/- 20sec)
5. Place the beam of the seesaw parallel to the ground and set
the switch to I.
6. Place the beam of the seesaw to the lowest position and set
the switch back to O.
7. The reset is complete.
9
LED Switch