PLAYSTAR Air Rider User manual

AAiirrRRiiddeerr
PS 7958
Call Toll Free 1-888-752-9782
Customer Service: Monday - Friday, 8:00 A.M. to 5:00 .M. C.S.T.
We’re Here To Help!
Play Act on ®
TM
Assembly Instructions
Important!
Intended for residential use by children ages 2 to 10, only on properly
installed layStar playsets. Before use refer to complete safety guidelines
in your original playset, at www.playstarinc.com, or at 1-888-752-9782.
Warning!
No more than two children should be allowed on this accessory at one time,
with a maximum weight of 105 pounds for each child.

(1) Air Rider
(4) Welded-Link Chains
(1) Swing Hanger
Assembly System
(1) Bracket System
Weather-Resistant
Hardware
Complete Illustrated
Instructions
CONTENTS TOOLS REQUIRED
HARDWARE INCLUDED (shown act al size)
3/8" x 7" hex bolt
3/8" flat washer
Socket Wrench and
Extension
⁹⁄₁₆" Socket
⁹⁄₁₆" or Adjustable
Wrench
Tape Measure
Safety Glasses
Drill
A r R der K t Contains:
SWING HANGER ASSEMBLY
1. osition one bracket on the beam, at least 10" away from the
closest point of all other rides or stationary objects. Make sure
the alignment tab is flush with the bottom of the beam as shown.
Using the bracket as a guide, drill two ³⁄₈" holes straight through
the beam. Install two ³⁄₈" x 4" hex head bolts with washers through
the bracket and beam to hold the bracket in place. (F g. 1)
2. Slide the second bracket in place over the bolts. Install one
washer and lock nut on each bolt and tighten nuts (you
will need a socket extension for this step). (F g. 1)
F g. 1
3/8" x 4" hex bolt 3/8" x 1¹⁄₄" hex bolt
(Swing Hanger Assembly)
3/8" x 1" hex bolt
(Air Rider Assembly)
3/8" lock nut
Beam
Square
Hammer
³⁄₈" Drill Bit
Hack Saw
Metal File
encil
Ladder
2⁹⁄₁₆"

4. Mark over 16" from center of bolts. Repeat Steps 1
through 3 for the second assembly. (F g. 3)
F g. 2
F g. 1
F g. 2
F g. 3
AIR RIDER ASSEMBLY
3. Install swing hangers to bracket using ³⁄₈" x 1¹⁄₄" hex
head bolts and lock nuts as shown. Tighten with ⁹⁄₁₆"
wrench and socket wrench. (F g. 2)
Caution: At least 10" minimum spacing is required from the closest point of all
other rides or stationary objects.
Caution: Cut off all protruding threaded ends of bolts ith a hack sa flush to the
end of the nut and remove sharp edges ith a metal file.
1. Connect handle to pivot arm using ³⁄₈" x 1" hex head
bolt, two washers, and lock nut as shown. Tighten with
⁹⁄₁₆" wrench and socket wrench. Repeat for other
assembly. (F g. 1)
2. Connect footrest to pivot arm using ³⁄₈" x 1" hex head
bolt, two washers, and lock nut as shown. Tighten with
⁹⁄₁₆" wrench and
socket wrench.
Repeat for other
assembly. (F g. 1)
3. Connect seat to pivot arm using ³⁄₈" x 7" hex head
bolt, two washers and lock nut as shown. Tighten
with ⁹⁄₁₆" wrench and socket wrench. Repeat for
other end. (F g. 2)
F g. 2
16"
3

Thank You fo choosing PlaySta ’s Play Action Ai Ride . Because it is ou intention to
make this a positive family expe ience, we have taken g eat ca e in p epa ing this p oduct.
Should you have any questions, o if we can assist you in any way, please call ou f iendly
Custome Se vice Depa tment fo immediate action.
Ask for Customer Service.
We Will Gladly Help!
rinted in U.S.A.LT 6414 R3
© 2004, layStar, Inc. Reproduction of this document in part or whole is prohibited without the permission of layStar, Inc.
layStar, Incorporated, Janesville, WI 53547
Please call us Toll Free at 1-888-PLAYSTAR
(752-9782)
Monday through Friday, 8:00 A.M. to 5:00 .M. C.S.T.
Do not return to the store.
4. Connect a length of chain to each hanger of handle
using one quick-link. Tighten with adjustable wrench.
(F g. 3)
Caution: Failure to tighten quick-links securely
could result in injury.
5. Lift Air Rider into position and hook chains onto the
swing hangers (F g. 3)
F g. 3