PLAYSTAR Play Action Contoured Leisure Swing Instruction Manual

Thank You fo choosing PlaySta ’s Play Action
Contou ed Leisu e Swing. Because it is ou intention
to make this a positive family expe ience, we have
taken g eat ca e in p epa ing this p oduct. Should
you have any questions, o if we can assist you in any
way, please call ou f iendly Custome Se vice
Depa tment fo immediate action.
Ask for Customer Service.
We Will Gladly Help!
Printed in U.S.A.T 6405 R5
© 2005, 2004, 2002, 1999 PlayStar, Inc. Reproduction of this document in part or whole is prohibited without the permission of PlayStar, Inc.
Protected by one or more of the following United States or Foreign Paents: US D428,637; US D424,154
PlayStar, Incorporated, Janesville, WI 53547
Please call us Toll Free at 1-888-PLAYSTAR
(752-9782)
Monday through Friday, 8:00 A.M. to 5:00 P.M. C.S.T.
Do not return to the store.

T.M.
Important!
This product is intended for use only on properly installed PlayStar playsets. Before using this
accessory refer to the complete safety guidelines provided with your original playset. To obtain a
free copy visit www.playstarinc.com or call 1-888-752-9782.
Warning!
awn swings are designed for use by children over two years of age. Use by children under the age
of two can result in entrapment between the seat and back area. Never place children in a rear-
ward facing position or with legs between the seat and backrest because the child’s body may pass
through the opening causing entrapment of child’s head. No more than three occupants should be
allowed on this accessory at one time, with a maximum weight of 105 pounds for each occupant.
Call Toll Free 1-888-752-9782
Customer Service: Monday - Friday, 8:00 A.M. to 5:00 P.M. C.S.T.
We’re Here To Help!
Play Action ®
Building Instructions
PS 7960

(2) Molded Sides
(4) Welded- ink Chains
(2) Swing Hangers
Weather-Resistant
Hardware
Complete Illustrated
Instructions
³|₈" x 3" Lag Screw (52) ³|₈" Washer (79)
#8 x 1¹|₄" Deck
Screw (10)
³|₈" x 3" Lag Screw (52) ³|₈" Washer (79)
#8 x 1¹|₄" Deck
Screw (10)
³|₈" x 3" Lag Screw (52) ³|₈" Washer (79)
#8 x 1¹|₄" Deck
Screw (10)
CONTENTS TOOLS REQUIRED
HARDWARE INCLUDED (shown actual si e)
3/8" x 3" lag screw
3/8" washer
Socket Wrench
⁹⁄₁₆" Socket
Adjustable Wrench
adder
Tape Measure
Safety Glasses
Drill
Square
Phillips Screwdriver
Saw
Hammer
1/8" & 1/4" Drill Bit
Pencil
Contoured Leisure
Swing Kit Contains:
CUTTING GUIDE
2" x 4" x 8' – three (3) boards required
6 Seat Rails
Boards 1 - 3
48" 48"
BUILDING INSTRUCTIONS
1. Insert the six 2" x 4" x 4' seat rails into the
openings of one of the molded sides.
(Fig. 1)
2. Adjust seat rails so there is
a 1/2" overhang on the
outside of the swing.
3. Repeat steps 1 and 2
for the other end.
Fig. 1
Detail
#6 x 11/4"
deck screw
MEASU E, MA K AND IDENTIFY ALL LUMBE BEFO E CUTTING. (IF YOU DO NOT WISH TO MA K ON LUMBE , USE
MASKING TAPE O CHALK.) CUT ALL LUMBE BEFO E BEGINNING CON ST UCTION.

4. Drill a 1/8" pilot hole in the center of each seat rail on
the inside edge of the molded side panel. (Fig. 2A)
5. Secure each seat rail with one #6 x 11/4" deck screw.
(Fig. 2B)
6. Attach one 40-link chain with a quick link connector
to the front support of molded side panel. Attach one
36-link chain with a quick link connector to the back
support of molded side panel. Tighten both quick link
connectors with an adjustable wrench. (Fig. 3)
7. Repeat Step 6 for opposite side. (Fig. 3)
8. ift the swing and hook the chains onto the swing
hangers, attaching the
back chains first.
9. If you are adding the Contoured eisure Swing to an existing PlayStar Play Action Set, the swing hangers are
already in place. Hang swing from the two outermost hangers inside swing bay. (Fig. 4A)
10. If you do not have swing hangers in place, you will need to install them now.
11. Make two marks in one beam board 48" - 53" apart, centered between posts. (Fig. 4A)
Caution: The Contoured Leisure Swing must be at least 10" away from the closest
point of all other rides or stationary objects.
12. Drill a 1/4" dia. hole 21/2" deep in the center
of each marked location. (Fig. 4A)
13. Screw swing hangers into beam by hand
(a long screwdriver will help). Tighten
swing hanger until loop is tight against
adjoining beam and swing hanger
is parallel with beam. (Fig. 4B)
14. Drill another 1/4" dia. hole 21/2" deep in
adjoining beam through swing hanger
loop and secure each swing hanger with
one 3/8" x 3" lag screw with washer. (Fig. 4B) Fig. 4A
Fig. 4B
48" - 53"
Fig. 2A
Fig. 2B
Drill (12 Places)
Detail
Fig. 3