Playworld Systems XX0598 User manual

Model XX0598
ECN2218
Page 1 of 14
Installation Instructions
Installation Instructions
Playworld Systems®Model XX0598
Quattro See-Saw
(w/ Seat Backs)
Installation Preparation
Recommended Crew: ...........................Two (2) adults
Installation Time: ...................................5 man-hours
Weight:..................................................*342.2 lbs. (155.5 Kilos)
Concrete Required:...............................0.24 cubic yard (0,18 cubic meter)
Use Zone:..............................................Refer to Use Zone information
User Group (ages): ...............................ASTM/CSA: 2-12 yrs, EN: 2-14 yrs
Assembly View
A
Use Zones: Quattro See-Saw
A= ASTM: 84 in. (2134 mm)
CSA: 2100 mm
EN: 1500 mm
*Weights are approximate for determining manpower.
ICON KEY
Fully Tighten
Hardware Add 1 Drop of Thread Locking Adhesive
Do Not Fully Tighten
Hardware Pour Concrete
Drill Dig Footing Holes
Hammer Critical Fall Height

Model XX0598
ECN2218
Page 2 of 14
Installation Instructions
6XSSRUW3RVW)RRWLQJ'HWDLO (1
PP
PP
PP
PP
*URXQG/H HO
&RQFUHWH
3URWHFWL H6XUIDFLQJ
/H HO
&RPSRQHQW
E6WRQH
6RLO
PP
'LDPHWHU
2"
(51 mm)
12"
(305 mm)
Diameter
See-Saw Support Post Footing Detail (CSA)
Ground Level
Concrete
Protective Surfacing Level
Support Post
2b Stone
6"
(152 mm)
30"
(914 mm)
36"
(1067 mm) 30"
(914 mm)
FOOTING NOTES
• Supportpostfootingdepth equals36 in.(914 mm)less thedepth ofthe protective
surfacing material. The post is designed to have 24" (610 mm) in concrete.
Example: If 6 in. (152 mm) of wood mulch is used for surfacing, the footing
depth would be 30 in. (762 mm).
• Componentfooting depth equals30 in.(762 mm) lessthe depthofthe protective
surfacing material. The post is designed to have 12" (305 mm) in concrete.
Example: If 12 in. (305 mm) of wood mulch is used for surfacing, the footing
depth would be 18 in. (457 mm).
• Allsupport postsandcomponent supportlegs shall haveeither afactory-applied
sticker with line, or factory-applied mark designating protective surfacing level
on a clear and level installation site.
• If play structure is installed on uneven terrain, maintain support post mark at
protective surfacing level at lowest grade. Adjust other footings accordingly.
Support posts and all attaching decks and play components must be plumb
and level.
• Donot encase bottomof support postinconcrete. Placepostdirectly onpacked
stone.
• Thefootings shownonPlayworldSystems’documentation arerecommendations
basedonhistorical performance inaverage soil conditions.Footingdimensions
may be modified by the owner based on actual soil conditions.
For example:
- If local soil is loose or unstable, a larger footing may be required.
- If local soil is considered stable, such as bedrock, clay or hard packed earth, a
smaller footing may be used. Before changing footing dimensions, we strongly
recommend that the footings be reviewed and approved by a registered
engineer.
• Base of footing must be below frost line.
• Assemble the entire structure before pouring concrete unless specifically
instructed to do so in the individual component installation instructions.

Model XX0598
ECN2218
Page 3 of 14
Installation Instructions
Footing Diagram
Elevation View
Top View
Surfacing Warning Label
Apply The Surface Warning Labels Here
17.8" (452 mm)
KEY
Position Unit of Measurement
Top # Inches
Bottom # [Millimeters]

Model XX0598
ECN2218
Page 4 of 14
Installation Instructions
Follow the details in alphabetical order. For clarification, each detail references the
step description. The step descriptions start on page 10.
Detail A
Step 4
Spring Wedge Casting
AAU0062
Spring
ATM0014
Base Plate
BFC1026
3/8" Flat Washer
BAE0595
3/8" Lock Nut
BAE0620
3/8" x 2"
Button Head Bolt
BAE06673
Detail B
Step 4
(both springs must be mounted the same way)
Detail C
Step 5
Base Frame
AFR1087
3/8" Hex Nut
w/ Locking Ring
BAE0621
3/8" Flat Washer
BAE0595 1.25" O.D. Flat Washer
BAE0690
1/2" Hex Lock Nut
BAE0720
Spring Wedge
AAU0062
Spring
ATM0014
3/8" x 2" U-bolt
BAE0028 1/2" x 2.94" U Bolt
BAE1574
Base Frame
AFR1087
3/8" Hex Nut
w/ Locking Ring
BAE0621
3/8" Flat Washer
BAE0595
Note: Arrange spring as shown in Detail A-2.
Ensure that the 1-1/2" U-bolt is lined up with the
outer two holes on the side of the mounting plate.
Bottom View of the frame.
3/8" x 1-1/2" U-bolt
BAE0027
(See Notes above right
and to the right)
Important Note: The 2.94" U-bolt
attaches through the spring wedge,
then the 2" U-bolt over the second
and bottom coil, and the 1-1/2" U-bolt
over the bottom coil.

Model XX0598
ECN2218
Page 5 of 14
Installation Instructions
Detail D
Step 7
Pivot Assembly
ASY0256
3/8" x 3/4"
Button Head Bolt
BAE0659
3/8" Flat Washer
BAE0595
Base Frame
AFR1087

Model XX0598
ECN2218
Page 6 of 14
Installation Instructions
3/8" Hex Nut
w/ Locking Ring
BAE0621 3/8" Hex Nut
w/ Locking Ring
BAE0621
1/2" Hex Lock Nut
BAE0720
3/8" Flat Washer
BAE0595
1.25" O.D. Flat Washer
BAE0690
3/8" Flat Washer
BAE0595
Spring Wedge
AAU0062
Spring
ATM0014
3/8" x 1-1/2" U-bolt
BAE0027
3/8" x 2" U-bolt
BAE0028
Detail F
Step 9
Detail E-1
Step 8
Spring Wedge Casting
AAU0062
Spring
ATM0014
Detail E-2
Step 8
See-Saw Frame
AFR1438
Detail E-3
Step 8
1/2" x 2.94" U Bolt
BAE1574
(See Notes over at
the right)
Note: Arrange spring as shown in Detail
D-3. Ensure that the 2.94" U-bolt is lined
up with the outer two holes on the side
of the mounting plate.
Bottom View of the frame.
Important Note: The 2.94" U-bolt
attaches through the spring wedge,
then the 2" U-bolt over the second
and bottom coil, and the 1-1/2" U-bolt
over the bottom coil.
3/8" Flat Washer
BAE0595
See-Saw Frame
AFR1438
Pivot Assembly
ASY0256
3/8" x 3"
Button Head Bolt
BAE06681
3/8" Lock Nut
BAE0620

Model XX0598
ECN2218
Page 7 of 14
Installation Instructions
Detail H
Step 11
Seat Mounting Bracket
ABC0188 (Left)
ABC0189 (Right)
3/8" x 1-1/4"
Button Head Bolt
BAE0666
3/8" x 1-1/4"
Button Head Bolt
BAE0666
3/8" Lock Nut
BAE0620
3/8" Flat Washer
BAE0595
3/8" Flat Washer
BAE0595
Plastic Trim
BFC1017 (Left)
BFC1018 (Right)
See-Saw Frame
3/8" Flat Washer
BAE0595
1" Bolts only
Detail G-1
Step 10
Detail G-2
Step 10
See-Saw Frame
AFR1438
Cover Panel
BFC0489
Cover Panel
BFC0489
See-Saw Frame
AFR1438
3/8" x 1-1/4"
Button Head Bolt
BAE0666
3/8" I.D. x 1-1/4" O.D.
Fender Washer
BAE0936

Model XX0598
ECN2218
Page 8 of 14
Installation Instructions
Detail I
Step 12
3/8" x 1-1/4"
Button Head Bolt
BAE0666
See-Saw Frame
Handle Side Panel
BFC0488
Detail J
Step 13
3/8" x 1-1/2"
Button Head Bolt
BAE06645
3/8" Flat Washer
BAE0595
Handle
AAU0086
3/8" Lock Nut
BAE0620

Model XX0598
ECN2218
Page 9 of 14
Installation Instructions
Detail K
Step 14
Seat Mounting Bracket
3/8" x 1"
Button Head Bolt
BAE0664
3/8" Lock Nut
BAE0620
3/8" Flat Washer
BAE0595
Seat Cover
BFC0487
3/8" Flat Washer
BAE0595
3/8" Flat Washer
BAE0595
3/8" Lock Nut
BAE0620
Detail L
Step 15
Seat Mounting Bracket
3/8" x 1"
Button Head Bolt
BAE0664
3/8" Lock Nut
BAE0620
3/8" Flat Washer
BAE0595
Seat Cover
BFC0487
3/8" Flat Washer
BAE0595

Model XX0598
ECN2218
Page 10 of 14
Installation Instructions
__Notes Before You Begin: Do notovertighten boltsduringassembly, onlysnug
tighten them unless otherwise instructed.
Carefully read and understand these installation instructions before you
begin.
__Step 1: Before attempting to assemble your equipment, please review all
installation information carefully. Should you experience any difficulty during the
installation process, please call us at the telephone number shown on the last
page of these instructions.
__Step 2: Separate and identify all components and hardware.
___Step 3: Excavate footings as shown in the Support Post Footing Details
on page 2 of this document.
Attach the spring to the base frame.
__Step 4: Attach the spring to the base frame. See Details A and B. Select
the base frame, the spring and the appropriate hardware. There are (3) three
connections. Lower the spring onto the base frame. Insert the spring wedge into
the end of the spring coil and rotate around until tight. Insert the U-bolts over the
spring and attach as shown.
Note:The 2.94"U-boltattaches throughthespring wedge, thenthe 2" U-boltover
the second and bottom coil, and the 1-1/2" U-bolt over the bottom coil.
Note: Repeat the procedure in Step 4 to attach a second spring to the opposite
end of the base frame.
Attach the base plate to the base frame.
__Step 5: Attachthebase plate tothebase frame. SeeDetail C. Selectthe base
plate and the appropriate hardware. There are (2) two connections. Raise the
base plate below the base frame and attach through the center of the spring as
shown. Fully tighten the hardware according to tightening torque specifications
in Step 16 of these instructions.
__Step 6: Place the base frame into the prepared footing. Plumb and level the
assembly. Fully tighten all fasteners according to tightening torque specifications
in Step 16 of these instructions. Block and brace for concrete. Pour concrete
and allow 72 hours for concrete to completely cure before continuing on with the
installation. Check the frame to ensure that it is plumb and level after pouring
the concrete.
Attach the pivot assembly to the base frame.
__Step 7: Attach the pivot assembly to the base frame. See Detail D. Select the
pivotassemblyand the appropriatehardware. Thereare (12) twelveconnections.
Position the pivot assembly down over the sides of the frame, align the holes,
apply a drop of thread locking adhesive to the bolt threads, and attach as shown.
Do not fully tighten the connections.
Attach the see-saw frame to the springs.
__Step 8: Attach the see-saw frame to the springs. See Details E-1, E-2, and
E-3.Selectthe see-saw frame,the spring wedges,andthe appropriate hardware.
There are (3) three connections per spring, (6) six total connections. Position the
see-saw frame with the flat side of the spring mounting plate facing down and
over top of the springs. Insert a spring wedge between the end and next spring
coil on the end of a spring and rotate around until it is tight. The tabs should be
on the top, next to the end coil. Position frame so the legs of the U-bolt stick up
throughthe holesinthe springmounting plate.Fullytighten connectionsaccording
to tightening torque specifications. See Step 16 of these instructions. Repeat
procedure to attach the frame to the other spring.
Note:The 2.94"U-boltattaches throughthespring wedge, thenthe 2" U-boltover
the second and bottom coil, and the 1-1/2" U-bolt over the bottom coil.
Attach the see-saw frame to the pivot assembly.
__Step 9: Attach the frame to the pivot assembly. See Detail F. Select the
appropriate hardware. There are (12) twelve connections. Align the holes in the
side of the frame with the holes in the pivot assembly and attach as shown. Fully
tighten the connections according to tightening torque specifications. See Step
16 of these instructions.
Attach the cover panel to the frame.
__Step 10: Attach the cover panel to the frame. See Detail G-1 and G-2. Select
the cover panel and the appropriate hardware. There are (4) four connections.
Place the cover panel on top of the frame and align the holes. The side of the
panel that has the routed out holes must be facing up. Apply a drop of thread
locking adhesive to the bolt threads and insert each bolt through the panel and
thread into the frame. Fully tighten the connections.

Model XX0598
ECN2218
Page 11 of 14
Installation Instructions
Attach the seat mounting brackets to the frame.
__Step 11:Attach the seat mounting brackets to the frame. See Detail H. Select
the(8) eightseat mountingbrackets,(8) eightpieces ofplastic trimand appropriate
hardware. There are (24) twenty four lower connections and (16) sixteen upper
connections. Position a bracket and piece of plastic trim against each end of the
see-saw frame and, using loctite on the 1" bolt threads only, make attachments
as shown.
Note: Four of the mounting brackets and plastic trim are designed to be mounted
on the left side of the see-saw frame and four on the right side. Hole patterns are
distinct and brackets can only be mounted on the correct side.
Attach the handle side panels to the frame.
__Step 12: Attach the handle side panels to the frame. See Detail I. Select
(8) eight handle side panels and appropriate hardware. There are (16) sixteen
connections. Position each side panel against the see-saw frame just ahead of
eachseat mountingbracket.Apply loctiteto thebolt threadsand makeattachments
as shown. Leave the connections loose.
Note: Ensure the handle side panels angle towards the seat mounting bracket.
Attach the handles to the side panels.
__Step 13: Attach the handles to the side panels. See Detail J. Select (8) eight
handles and the appropriate hardware. There are (32) thirty two connections.
Position each handle between the top or bottom of each pair of side panels and
make attachments as shown.
Attach the seat covers to the seat mounting bracket.
__Step 14: Attach the seat covers to the seat mounting bracket. See Detail K.
Select (4) four seat covers and the appropriate hardware. There are (16) sixteen
connections. Position each seat cover, with the countersunk holes up, over the
bottom of the seat mounting brackets and make attachments as shown.
Attach the seat covers to the seat back.
__Step 15: Attach seat covers to the seat back. See Detail L. Select (4) four
seat covers and the appropriate hardware. There are (16) sixteen connections.
Position each seat cover, with countersunk holes out, against the seat backs and
make attachments as shown.
Final Details.
__Step 16: Plumb andlevel entire component.Tightenall fasteners. Fullytighten
all fasteners according to tightening torque specifications.
Torque Specifications:
Bolts and nuts - Snug tighten and then tighten an additional one half turn.
Note: Check for proper operation. Frame should pivot smoothly on the shaft.
__Step 17: For areas complying with ASTM standard F1487 and CSA Z-614,
apply the age appropriate label at a visible location on the equipment.Also apply
the Surface Warning labels at the locations indicated on the Elevation View.

Model XX0598
ECN2218
Page 12 of 14
Installation Instructions Bill of Materials
PW - QUATTRO SEE-SAW (w/ SEAT BACKS)
PART NO. DESCRIPTION QTY.
AAU0062 CASTING - 7-3/32" O.D. SPRING WEDGE 4
AAU0086 HANDLE - 4-5/16" x 5" x 14-19/32" 8
ABC0188 BRACKET - 11" x 13.67" x 4.62" LEFT 4
ABC0189 BRACKET - 11" x 13.67" x 4.62" RIGHT 4
AFR1087 FRAME - 30.27" x 13.63" x 28.00" 1
AFR1438 FRAME - 92.90" x 31.75" x 4.18" 1
ASY0256 QUATRO SEE-SAW PIVOT ASSEMBLY 1
ATM0014 SPRING - 400mm 2
BAD0085 THREAD LOCKING ADHESIVE 2
BAE0027 BOLT - 3/8"-16 x 7/8" x 1-1/2" U 4
BAE0028 BOLT - 3/8"-16 x 7/8" x 2" U 4
BAE0595 WASHER - 3/8" SAE FLAT 174
BAE0620 NUT - 3/8"-16 LOCK w/NYLON CAP 90
BAE0621 NUT - 3/8"-16 ZINC HEX w/LOCKING RING 16
BAE0659 BOLT - 3/8"-16 x 3/4" BUTTON HEAD - SS 12
BAE0664 BOLT - 3/8"-16 x 1" BUTTON HEAD - SS 32
BAE06645 BOLT - 3/8"-16 x 1-1/2" BUTTON HEAD - SS 32
BAE0666 BOLT - 3/8"-16 x 1-1/4" BUTTON HEAD - SS 76
BAE06673 BOLT - 3/8"-16 x 2" BUTTON HEAD - SS 2
BAE06681 BOLT - 3/8"-16 x 3" BUTTON HEAD - SS 12
BAE0690 WASHER - .531" I.D. x 1.250" O.D. x .060" THICK 8
BAE0720 NUT - 1/2"-13 LOCK 8
BAE0910 TOOL - 1/4" SHORT HEX KEY WRENCH 1
BAE0922 TOOL - TT 45 L WRENCH 2
BAE0936 WASHER - 3/8" I.D. x 1-1/4" O.D. FENDER 4
BAE1574 BOLT - 1/2"-13" x .75" x 2.94" U 4
BFC0487 SHEET - .75" x 8" x 12" 8
BFC0488 SHEET - .75" x 16.93" x 7.86" 8
BFC0489 SHEET - .75" x 26.00" x 40.00" 1
BFC1017 PANEL - 11.01" x 13.43" x .50" - TRIM, LEFT 4
BFC1018 PANEL - 11.01" x 13.43" x .50" - TRIM, RIGHT 4
BFC1026 SHEET - .50" x 9.50" x 11.00" 2
ALB0025 LABEL - AGE APPROPRIATE SHEET 1
1000 Buffalo Road • Lewisburg, PA 17837
www.playworldsystems.com
For Customer Service, Call
800-233-8404 or
570-522-9800 OUTSIDE U.S.

Model XX0598
ECN2218
Page 13 of 14
Installation Instructions
Spring
• Inspect the spring to insure they are properly secured
to the anchor and spring plates. Check spring U-bolts to
ensure secure connections. If any damage is detected,
barricade equipment to prevent use until repair is
completed.Contactyoursalesrepresentativeimmediately
for a replacement part.
Plastic Parts
• Inspect all plastic surfaces for sharp points, cracks
or jagged edges. If any damage is detected and is
determinedto be unsafe,barricade equipment toprevent
use until repair is completed. Minor burrs or sharp edges
may be removed by using a sharp utility knife or block
plane to remove sharp burr.
Fasteners
• Inspectforloosefasteners.Tighteningtorquespecifications
are:
Bolts and Nuts: Snug tighten and tighten an additional
one-half turn.
• Inspect for missing, worn or broken fasteners. If any
missing, worn or broken fasteners are found, refer to the
installation instructions for proper replacement fastener.
If any damage is detected, barricade equipment to
prevent use until repair is completed. Contact your sales
representative immediately for a replacement part.
• If during the maintenance process a bolt needs to be
removedfrom apart or parts,it will benecessary to apply
a drop of liquid thread lock / loctite to the bolt before
reinstallation.
Welds
• Inspectallweldedjoints. If any broken weldsare detected,
barricade equipment to prevent use until repair is
completed.Contactyoursalesrepresentativeimmediately
for a replacement part.
Equipment Maintenance
Playworld Systems®
Model XX0598
Quattro See-Saw
(w/ Seat Backs)
Castings
• Visually inspect handles and end caps for cracks or
breakage.Ifanydamageisdetected,barricade equipment
topreventuseuntilrepairiscompleted. Contact your sales
representative immediately for a replacement part.
Finish
• Inspect metal parts for finish damage.
To repair painted surfaces, sand damaged area with
sandpaper and wipe clean. Mask area and paint with
primer and allow to dry. Paint primed area with color-
matching paint and allow to dry. Recoat area with color-
matching paint if required. Drying time is approximately
8 hours between coats.
Footings
• Inspect component to be securely attached to the spring
and solid in the footing. If any damage is detected,
barricade equipment to prevent use until repair is
completed.
Surfacing
• Refer to the specific surfacing maintenance detail sheet
for additional information.
Replacement Parts
• Refertoyourinstallationinstructionstoobtainreplacement
part number.
• Contact your sales representative or call Playworld
Systems’ Customer Service for replacement part.
1000 Buffalo Road • Lewisburg, PA 17837
www.playworldsystems.com
For Customer Service, Call
800-233-8404 or
570-522-9800 OUTSIDE U.S.

Model XX0598
ECN2218
Page 14 of 14
Installation Instructions
Inspection Form
• Be sure that you are using a copy of this Inspection Form and not your original.
• Use the Inspection Codes listed below and record condition of equipment at time of
examination on the Inspection Checklist.
• Document any item from the Inspection Checklist that will require maintenance along with
any corrective action on the Maintenance Schedule.
• Be sure to include appropriate dates and signatures on each section to properly document
maintenance procedure.
Preventive Maintenance
. . . for Safety's Sake!
Repairer: Name (Please Print) __________________________________ Signature:________________________________________ Date:___ /___ /___
MAINTENANCE SCHEDULE
Item in Question Description of Problem Corrective Action Date
Inspector: Name (Please Print) __________________________________ Signature:_________________________________________ Date:___ /___ /___
Inspection Codes
P = Pass F = Fail
NA = Not Applicable
INSPECTION CHECKLIST Frequency Inspection Code Date Date Repairs Completed
Inspect plastic parts for damage. Medium
Inspect spring connections for tightness. High
Inspect metal parts for structural and finish damage. Medium
Inspect for loose, missing, worn, or broken fasteners. High
Inspect footing to insure support is secure and footing is not damaged. Low
Inspect surfacing to insure proper depth and distribution. High

Guidelines & Information (fs RS_stand) Annex Page 1
Guidelines
Rocking/Springing Equipment
Intended for Standing Use Zones
A= ASTM: 84 in. (2134 mm)
CSA: 2100 mm
EN: 1500 mm
Important ! Please Read Completely Before Beginning Installation. According
toa reportpublished bythe U.S. ConsumerProduct SafetyCommission (C.P.S.C.)
72% of all playground injuries result from accidental falls. With this in mind, this
equipment is designed to fill the need for safe yet challenging play. In conjunction
with design efforts to reduce the possibilities of injuries, this equipment must be
installed "Step by Step" per our installation instructions. As a new owner you
are responsible for the correct installation, safe use, and maintenance of your
equipment.
Installation Guidelines
• Identify all parts and thoroughly read the assembly instructions before
beginning construction.
• Refer to your playground equipment plan and footing diagram to assure
the equipment purchased will fit into your selected site area. The use and no-
encroachment zones around the play equipment shall be obstacle-free areas
designated for unrestricted circulation.
• ASTM compliance: For rocking/springing equipment intended for standing,
the use zone should extend on all sides a minimum distance of 84 inches (2134
mm). This use zone may not be overlapped by the use zones of adjacent play
equipment. See diagram.
• CSA compliance: For rocking/springing equipment intended for standing,
the use zone should extend on all sides a minimum distance of 2100 mm. This
use zone may not be overlapped by the use zones of adjacent play equipment.
See diagram.
• EN Compliance: For rocking/springing equipment intended for standing, the
use zone should extend on all sides a minimum distance of 1500 mm.
• Site layout is a critical part of the overall installation. Footings must be
measured and marked accurately according to the footing diagram. A level and
clear installation site is ideal.
• Good drainage around the structure and its supports is important. Inquire
with local contractors for appropriate recommendations.
• After laying out all footings and before digging holes, be sure to inquire about
underground utilities that may exist.
• Do not leave the job site unattended without making sure that all fastening
hardware on all components are tightened according to tightening torque
specifications listed on every installation guide. We also recommend roping off
construction area and covering all holes that do not contain a piece of equipment
with plywood or other suitable material.
• Excavate holes as shown in the footing detail. If a level and clear site cannot
be obtained, adjust the depth of footing to maintain a level footing base. If soil
conditionsare looseor unstable,a largerdiameter footingmayberequired. Inquire
with local contractors for appropriate recommendations. Be sure concrete that
might have splashed onto the unit is washed off before it dries. Allow concrete to
harden 72 hours before allowing your structure to be used. Assemble the entire
structure before pouring concrete unless specifically instructed to do so in
the installation instructions.
• Insure that Age Appropriate and Hard Surface Warning/Playworld Systems
identification labels are properly affixed to the play equipment. Labels are to be
plainly visible according to current playground equipment guidelines.
A
A
A
Placement of multiple rocking springing
equipment intended for standing

Guidelines & Information (fs RS_stand) Annex Page 2
• IMPORTANT! Because accidental falls around your playground equipment
can occur, Playworld Systems recommends that the area under and around the
structure be covered with a resilient material such as sand, bark mulch, or wood
chips. If loose fill surfacing materials are used, Playworld Systems recommends
a depth of 12 in. (305 mm). An approved rubber safety matting can also be
used. Many protective surfacing materials can become compacted due
to weather and use, which reduces their shock absorbency. It is strongly
recommended that the surfacing be checked weekly and material added
or replaced as necessary. Hard surfaces, such as asphalt, concrete and
packed earth are not acceptable for use under playground equipment.
• The entire area, under and around the playground equipment, must be
covered with protective surfacing material. The impact attenuation of the
protective surfacing under and around playground equipment should be rated to
have a critical height value of at least the height of the highest accessible part
of the equipment. The critical height for surfacing is to be rated in accordance
with A.S.T.M. standard, designated F1292, A Standard Specification for Impact
Attenuation of Surface Systems Under and Around Playground Equipment.
Contact the manufacturer of unitary surfacing materials (rubber matting) for the
critical height rating for their products.
ToolsRequired: PlayworldSystemssuppliesaservicekit thatcontains commonly
used hex key wrenches required to assemble your equipment. You may also
need:shovel,digging iron, posthole digger, steel rake,wheelbarrow,garden hoe,
water hose, tape measure, level, alignment tool, 3/8" ratchet with 9/16" socket,
and 9/16" combination wrench.
Maintenance
• Inadequate maintenance of equipment has resulted in injuries on the
playground. Becausethe safetyofplayground equipmentand itsstability depends
ongoodinspection and maintenance,a comprehensive maintenance program
must be developed for each playground and strictly followed. All equipment
must be inspected frequently for any potential hazards. Special attention must
to be given to moving parts and other components that can be expected to wear.
Inspections must to be carried out in a systematic manner by trained personnel.
Any damaged or worn parts, or any other hazards identified during inspections
must be repaired or replaced immediately. Complete documentation of all
maintenance inspections and repairs must be retained.
Supervision Guidelines
• PlayworldSystems strongly recommendsclosesupervision of thechildren as
theyplay as wellas intensive classroomand homeinstructionabout safebehavior
on playground equipment.
• Playgroundsupervisorsshould be awarethat not allplaygroundequipment is
appropriate for all children who may use the playground. Signs should be posted
near the equipment indicating the recommended age of the users. Supervisors
should direct children to equipment appropriate for their age.
• It is important that playground supervisors recognize that preschool-age
children require more attentive supervision on playgrounds than older children.
• Do not permit the use of wet playground equipment. Wet equipment will
inhibit necessary traction and gripping capabilities. Slips or falls could occur.
• Do not permit too many children on the same piece of equipment at the same
time. It is suggested that children take turns.
• Constantly observe play patterns to discover possible hazardous play and
suggest changes in equipment use or play patterns.

Guidelines & Information (fs RS_stand) Annex Page 3
FINAL INSPECTION
• Playworld Systems®insists on the installation of protective surfacing within the
usezone of eachplaystructure in accordancewith the applicablespecifications
in your area appropriate for the fall height of each structure.
• Playworld Systems®strongly recommends close supervision of children as
they play. The owners of playground equipment and the parents or guardians
of children are responsible for this proper supervision.
• Asthe ownerofplayground equipment,you areresponsiblefor themaintenance
ofthe equipmentandsurrounding playarea.Acomprehensivemaintenance and
inspectionschedule must bedevelopedand allequipmentinspected frequently.
Refer to the inspection and maintenance schedule in the back of this booklet.
• Perform a thorough final check on the installed equipment to insure all
equipment is installed as specified by manufacturer’s installation instructions.
• Review all Installation Instructions for specified dimensions. Make sure
dimensions called for in instructions agree with actual installation.
• Doublecheckheight dimensions. Heightmeasurements are takenfromthe
top of the protective surfacing material.
• Insureallfastenersaretightenedaccordingtotighteningtorquespecifications
listed on your installation instructions.
• Insure all exposed pipe ends have properly installed end caps. Insure that
drive rivets are secure.
• Clean dried concrete off of components and any other affected surface.
• Touch-upanyscratches or installationdamage to powdercoatedfinish with
color-matched spray paint.
• Allow adequate time for proper curing, both for concrete and urethane
cement if rubber safety surfacing tiles have been installed.
• Insurethat protectivesurfacingis properlyinstalled accordingto C.P.S.C. (or
other appropriate body) recommendations. Footings must not be exposed.
• Insurethat hardsurface warning/PlayworldSystems®identificationlabels are
properlyaffixedto the playequipment. Labels areto be plainly visibleaccording
tocurrent playground equipmentguidelines. Forlocationscomplying withASTM
F1487 or CSA Z-614, Age Appropriate labels must also be applied in a visible
location.
• Dispose of all packaging material properly. These materials which include
large plastic bags and sheets can be a suffocation hazard. Dispose of these
materials out of reach or contact of small children.
Surfacing Warning Label