Plymovent VSRX User manual

www.plymovent.com
vSRX
Vehicle Square Rail with External Trolley -
with Magnetic Grabber®
User manual
Thank you for buying this Plymovent product.
Before you put this system into operation
please read this product manual carefully, and
follow the instructions.
This manual is intended to be used as a work
of reference for an authorized professional to
safely install, use, maintain and service the
Plymovent VSRX system.
This manual should be handed over and kept
by the service department after the
installation.

EN - ORIGINAL INSTRUCTION
All rights reserved. The information given in this document has been collected for the general convenience of our clients. It has been
based on general data pertaining to construction material properties and working methods known to us at the time of issue of the
document and is therefore subject at anytime to change or amendment, and the right to change or amend is hereby expressly
reserved. Changes may be made with or without notication, it is the users responsibility to ensure they have attained the most
recent copy of this document for their les. The instructions in this publication only serve as a guideline for installation, use,
maintenance and repair of the product mentioned on the cover page of this document. This publication is to be used for the standard
model of the product of the type given on the cover page. Thus the manufacturer cannot be held responsible for any damage
resulting from the application of this publication to the version actually delivered to you. This publication has been written with great
care. However, the manufacturer cannot be held responsible, either for any errors occurring in this publication or for their
consequences.

Table of Contents
General Precautions....................................................................................................................4
Preface .....................................................................................................................................5
1 Introduction .............................................................................................................. 5
1.1 General description......................................................................................... 5
1.2 Product combinations...................................................................................... 5
1.3 Technical data ............................................................................................... 5
1.4 Method of use ................................................................................................ 5
1.5 Installation .................................................................................................... 5
1.6 Use ............................................................................................................. 6
1.7 Service, maintenance and repairs ..................................................................... 6
1.8 Tools............................................................................................................. 6
2 Area of Use ........................................................................................................................7
3 Delivery.............................................................................................................................8
4 Installation....................................................................................................................... 10
4.1 Mounting instructions.....................................................................................10
4.2 Back-In Measurements...................................................................................11
4.3 Drive-Through Measurements..........................................................................12
4.4 VSRX-Rail Location ........................................................................................13
4.5 Assemble the Legs and Rail.............................................................................14
4.6 Mount the Rubber Seal...................................................................................15
4.7 Install the End Caps.......................................................................................15
4.8 Hang the Rail and Connect to Duct...................................................................15
4.9 Assemble and Hang the Hose and Grabber........................................................16
4.10 Install the PC-500 Pressure Switch...................................................................17
5 Modifying the Tailpipe ................................................................................................17
5.1 Install the Tailpipe Connector ..........................................................................17
5.2 Modify the Tailpipe.........................................................................................17
5.3 Check the Balancer Tension ............................................................................18
5.4 Safety Disconnect Handle ...............................................................................18
5.5 Tailpipe Modication Options ...........................................................................18
6 User and Maintenance Instructions ..............................................................................20
6.1 Operating the Magnetic Grabber® ....................................................................20
6.2 Inspection and Maintenance............................................................................20
7 Cleaning and FAQ......................................................................................................21
7.1 Hose package ...............................................................................................21
7.2 Other Components ........................................................................................21
7.3 VSRX-Rail and Suspensions.............................................................................21
8 Disposal...................................................................................................................21
9 Spare Parts ..............................................................................................................22

MAN_MAG_VSRX_290518_LETTER_EN Page 4 of 24
GENERAL PRECAUTIONS
IMPORTANT USER INFORMATION
Read this document in entirety before you install, congure,
operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in
addition to requirements of all applicable codes, laws and
standards.
Activities including installation, adjustments, putting into service,
use, assembly, disassembly, and maintenance are required to be
carried out by suitably trained personnel in accordance with
applicable code of practice.
If this equipment is used in a manner not specied by the
manufacturer, the protection provided by the equipment may be
impaired.
In no event will Plymovent be responsible or liable for indirect or
consequential damages resulting from the use or application of
this equipment.
The examples and diagrams in this manual are included solely
for illustrative purposes. Because of the many variables and
requirements associated with any particular installation,
Plymovent cannot assume responsibility or liability for actual use
based on the examples and diagrams.
No patent liability is assumed by Plymovent with respect to use
of information, circuits, equipment, or software that may be
described in this manual. Throughout this manual, when
necessary, notes may be used to make you aware of safety
considerations.
The operation of exhaust extraction systems can be aected by
various factors including but not limited to proper design of the
system, operating procedures, service and maintenance. Fume
exhaust exposure levels should be checked upon installation and
periodically thereafter to ensure that they fall within applicable
regulations and exposure limit values.
Plymovent systems are made code compliant, please ensure the
system is properly designed, operated, serviced and maintained.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

MAN_MAG_VSRX_290518_LETTER_EN Page 5 of 24
PREFACE
Using this manual
This manual serves as a work of reference for professional, well
trained and authorized users to be able to safely install, use,
maintain and repair the VSRX system. This manual should be
handed over and kept by the service department after the
installation.
Pictograms and symbols
The following pictograms and symbols are used in this manual:
ATTENTION
A remark with additional information for the user. A
remark brings possible problems to the user’s
attention.
CAUTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
WARNING!
Procedures which, if not carried out with the
necessary caution, may damage the product or cause
serious personal injury.
CAUTION!
Risk of electric shock.
WARNING!
Fire hazard! Important warning to prevent re.
Text indicators
Listings indicated by “-” (hyphen) concern enumerations.
Listings indicated by “•” (bullet point) describe steps to perform.
Service and technical support
For information about specic adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specications at
hand:
- product name
1 INTRODUCTION
1.1 General description
The Vehicle Square Rail - External Crab Trolley (VSRX) with
Magnetic Grabber removes toxic exhaust gasses within the re
station.
1.2 Product combinations
VSRX can be used in back in and drive through applications with
multiple vehicles inline. Systems are available from 20 ft to 120
ft (6 to 37 m) in length with available hose diameters of 4 and 5
in. (100 and 125 mm).
1.3 Technical data
VSRX consists of a number of parts of which the Plymovent
yellow and black extraction hose assembly is most visible to the
user.
The extraction hose has a Safety Disconnect Coupling built in,
which protects the system from damage in the unlikely event
that the Magnetic Grabber catches on the vehicle. The hose is
suspended by a metal saddle that is attached to the balancer.
The balancer is connected to the aluminum suction rail via a
special trolley and sealed to the suction rail via exible rubber
lips. This enables the trolley to move along the suction rail as the
vehicle moves inside the re station.
The VSRX system consists of a strong rectangular aluminium
prole with a section area of 43.4 square in. (280 cm2). The
underside of the rail is an open area sealed with rubber lips. The
prole is connected to the ducts system by a 6.3 in. (160 mm)
exible hose.
1.4 Method of use
An automatic, magnetic exhaust gas extraction system,
specically designed for exhaust extraction of re and rescue
vehicles with low level, undercarriage exhaust pipes. The system
is used to remove toxic vehicle exhaust at the emission source,
the exhaust pipe.
As a vehicle moves within the facility, the extraction hose,
connected to the tailpipe by the Plymovent Magnetic Grabber®,
moves along with the vehicle.
Exhaust passes from the Grabber through the extraction hose
and into the ducting and extraction fan before escaping to the
atmosphere.
As the vehicles travel within the facility, the trolley moves to the
end of the rail. There the balancer locking cable restricts the
balancer to unwind, pulling the Grabber from the conical tailpipe
adapter, allowing it to disconnect.
On the return of the vehicle to the station, the Grabber can be
easily reconnected to the exhaust pipe. At the same time the
fan automatically starts up and the vehicle continues to its
standard park position.
1.5 Installation
The installation of this system should only be performed by
trained and authorized persons. If others are involved in the
installation, it should be done under the supervision of a
responsible and authorized person.
Please use appropriate ling materials and equipment when
working in an area over 6.5 feet (2 m).
Never install the product in front of entries, exits or passage
ways that are used by re and emergency service personnel.
Before starting the installation, conrm that the walls and/or
roof structures can support the weight of the system.

MAN_MAG_VSRX_290518_LETTER_EN Page 6 of 24
1.6 Use
a. Inspect the product and check for damages. Verify the
functioning of the safety features.
b. Check the working area. Please keep unauthorized people
away from the working area.
c. Protect the product against water and humidity.
d. The user of the product always has full responsibility for the
correct execution of the safety guidelines and instructions.
These are all the safety guidelines and instructions which
apply to the use of the system.
1.7 Service, maintenance and repairs
Observe the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the warranty null and void.
Always use tools, materials, lubricants and service techniques
which have been approved by the manufacturer. Never use worn
tools and do not leave any tools in or on the product.
Safety features which have been removed for service,
maintenance or repairs, must be put back immediately after
nishing these jobs and it must be checked that they still
function properly.
Please ensure that no vehicle enters or exits the station during
the service, maintenance and repair activities.
1.8 Tools
These tools are needed to install this Plymovent System:
- cordless drill
- cordless impact driver
- drill bits
- wrenches
- hammer drill
- anchors
- tape measure
- plumb bob or laser plumb
- level
- screwdrivers
- reciprocating saw
- core drill
- scissor lift
Please note that additional tools and machines may be needed
depending on the installation situation (installation height,
building construction, space available, etc).
ATTENTION!
After shutting down the ventillation system wait a
minimum of 10 seconds before handling the system
and products when performing service, maintenance
and or repairs.
ATTENTION!
Stay alert and pay attention during the installation.
Do not use the product when you are under the
inuence of drugs or alcohol.
Diesel or gasoline engine exhaust emissions, which
may contain carbon monoxide, benzene, napthalene,
pyrene, PAH’s, etc., should NEVER be recirculated.
These emissions must always be exhausted outside.

ATTENTION
The VSRX system is designed to operate under
standard vehicle performance conditions. DPF
(diesel particulate lter) re-generation on 2007 and
newer vehicles is not considered to be a standard
vehicle performance condition and should never be
performed inside the re or EMS station.
MAN_MAG_VSRX_290518_LETTER_EN Page 7 of 24
2 AREA OF USE
The VSRX system is used in re and emergency service stations,
where there are multiple vehicles parked behind an exit door
waiting for an emergency call.
The VSRX system is designed to be connected to the vehicle
while standing in an upright position. The operator will not need
to bend over, which will reduce her/his exposure to harmful
exhaust emissions.
Side View
Rail
Trolley
Magnetic Grabber®
Duct/Hose
Connector
Support leg
End stop with
shock absorber
WARNING!
Do not put hands or other body parts in the
Grabber.

MAN_MAG_VSRX_290518_LETTER_EN Page 8 of 24
3 DELIVERY
All of the VSRX models are built from the following standard
components.
Support leg
The aluminium support leg is used for both vertical and
horizontal mounting. The standard length is 19 ft (5790 mm)
and has to be cut to proper lengths. The dimension is 2 in. x 2
in. x 0.1 in. (50 x 50 x 2.5 mm).
Side brace
There are three dierent lengths available, 20 in. (500 mm), 30
in. (750 mm) and 6 ft (1800 mm). The brace can be mounted
separately or in pairs using the same brackets.
Side brace clamp kit
The kit includes two aluminium brackets for one or two side
braces.
Adjustable mounting kit (vertical)
The two brackets are similar. They can also be used if the roof is
angled and they can be mounted in both directions.
Maximum angle is 30 degrees.
VSR extraction rail
The VSR-rail is 19 ft (5,8 m) and ordered in 5 ft (1,5 m)
increments. The rubber lip seal that is delivered has been
measured for the rail that is ordered, and must be inserted into
the rail.
Balancer
The non-locking spring recoil balancer has a lifting capacity of
17.6 - 37 lbs (8 - 17 kg) with a cable length of 6.6 feet (2.2 m).
The main function of the Balancer Locking Cable (BLC) is to
control the point of disconnection. As the hose reaches it’s
maximum length, the BLC will bottom out, in turn pulling the
Magnetic Grip nozzle from the moving vehicle.

1
5
7
2
6
4
3
MAN_MAG_VSRX_290518_LETTER_EN Page 9 of 24
Crab Trolley
The ventilated sliding crab runs outside of the rail and can be
positioned anywhere along the rail.
Hose Kit
Hose kits available:
- ST (standard temperature) hose, 400°F (204°C) continuous,
500°F (260°C) intermittent,
- HT (high temperature) hose, 900°F (480°C) continuous,
1,050°F (567°C) degrees intermittent (upper, mid and lower
hose)
- Hose diameter is either 4 in (100 mm) or 5 in. (125 mm)
- Magnetic Grabber 3 in. (75 mm), 4 in. (100 mm) 5 in. (125
mm)
The dierent hose packages which contain the following parts:
- Transition parts
- Exhaust removal hose with clamps (1)
- Hoses: (1) Upper, (2) Mid and (3) Lower hose
- Metal hose saddle (4)
- Safety disconnect handle (5)
- Magnetic Grabber®nozzle (6)
- Magnetic Grabber®conical tailpipe adapter (7)
VSRX End Caps
The metal end cap is 13.3 in. (338 mm) in length, and 9.3 in.
(236 mm) in width, and should be bolted to each end of the rail,
as it allows for safe and eective stopping of the trolley.
Shock Absorber
The hydraulic shock absorber is inserted into bottom of the VSRX
End Cap on the entry door side, and secured with two hex nuts
that are included.

Rail height
Trolley
Magnetic Grabber®
Distance end stop/door
Length BLC
4 INSTALLATION
4.1 Mounting instructions
- Determine the installation height of the rail (measured from
the bottom of the rail) (1).
- Determine the recommended distance from the end stop to
the door in the Installation Table (2).
- Determine the recommended balancer locking cable (BLC)
length in the Installation Table (3).
- After installation, ne tune the BLC if the disconnection point is
not close enough to the door.
Rail height Distance end stop / door (2) Length BLC(3)
Feet m Feet m Inch cm
12’ 3
min 5.5 1.7 26 66,0
Recommended 6.0 1.8 30 76,2
max 7.0 2.1 32 81,3
Rail height Distance end stop / door (2) Length BLC (3)
Feet m Feet m Inch cm
13’ 4
min 6.5 1.9 26 66,0
Recommended 7.0 2.1 30 76,2
max 8.0 2.4 32 81,3
Rail height Distance end stop / door (2) Length BLC (3)
Feet m Feet m Inch cm
14’ 5
min 7.5 2.3 26 66,0
Recommnded 8.0 2.4 30 76,2
max 9.0 2.7 32 81,3
Installation Table:
Length BLC
3
2
1
MAN_MAG_VSRX_290518_LETTER_EN Page 10 of 24

CAUTION
Be sure to order the right Grabber dimension. If a
incorrect version is used on the tailpipe, the system
could be damaged or will not properly remove
exhaust from the facility.
MAN_MAG_VSRX_290518_LETTER_EN Page 11 of 24
4.2 Back-In Measurements
Please determine the position of:
1. Exhaust pipe
2. Garage / Exit door.
3. Distance from Exit door to the tailpipe.
a. Determine the location of the exhaust pipe (1) on the vehicle:
- Which side of the vehicle is the tailpipe positioned?
- Where does the exhaust exit the vehicle?
- What is the diameter of the tailpipe?
Determine if tailpipe modication is necessary, see ”Modify
the tailpipe” in this manual.
b. Measure the height and width of the garage (2). Determine
the type of bay doors:
- Rollup Door
- Segmented Panel Overhead Door (four-fold doors)
- Other type
Determine the height that the rail can be installed under the
door when fully raised.The height should be in line with the
specications indicated in this manual in order to ensure
correct product performance.
c. Measure the distance between the door and the exhaust
pipe (3). This is the required minimum length of the VSRX
rail. Check before installation that this is the minimum
required length of the VSRX in back-in application.
The distance from the end of the rail to the door(s)
must be in line with the installation table on page 10.
WARNING
PRODUCT MAY CONTAIN SHARP EDGES
Use care when servicing unit.
Failure to do so could result in minor personal injury.
3
2
1
Plan View

Plan View
3
2.1
2.2
1
MAN_MAG_VSRX_290518_LETTER_EN Page 12 of 24
WARNING
PRODUCT MAY CONTAIN SHARP EDGES
Use care when servicing unit.
Failure to do so could result in minor personal injury.
4.3 Drive-Through Measurements
Please determine the position of:
1. Tailpipe
2.1 Entrance door.
2.2 Exit door.
3. Distance between Entrance door / Exit door.
a. Determine the location of the exhaust pipe (1) on the vehicle:
- Which side of the vehicle is the tailpipe positioned?
- Where does the exhaust exit the vehicle?
- What is the diameter of the tailpipe?
Check if exhaust pipe modication is necessary, see “Modify
the Tailpipe” in this manual.
b. Measure the height and width of the garage (2.1 and 2.2).
Check the type of bay door:
- Rollup door
- Segmented panel overhead door (four-fold doors)
- Other type
Check at what height the rail can be installed. The height
should be in line with the specications indicated in this
manual in order to ensure correct product performance.
c. Measure the distance between the entrance door and exit
door minus two (2x) times the distance between the end of
the rail and the exit door (3) distance shown in the Installation
Table on page 10.
The distance from the end of the rail to the door(s) must fall
in the distrance shown in the Installation Table on page 10.
CAUTION
Be sure to order the right Grabber dimension. If a
incorrect version is used on the tailpipe, the system
could be damaged or will not properly remove
exhaust from the facility.

4.4 VSRX-Rail Location
1. VSRX-Rail
2. Tailpipe
3. Bay door
4. Rail height
5. Distance to vehicle
6. Distance to exit door
a. The VSRX-Rail (1) is mounted at a height (4) between 12 ft
(3,7 m) and 14 ft (4,3 m) over the oor on the side in which
the tailpipe (2) is located.
b. The rail should be mounted 18 in. to 24 in. (457,2 to 609,6
mm) from the body of the vehicle (5), and positioned on the
tailpipe side of the vehicle. Preferably the rail is on or within
the boundaries of the exit door.
c. The rail should be mounted immediately under a sectional
door with a clear height from the track to the door of 4 in.
(100 mm) to 6 in. (150 mm).
d. The recommended distance from the end of the rail to the
door(s) (6) can be found in the table on page 10.
End View
18 to 24 in.
2
1
4
6
5
3
Side View
MAN_MAG_VSRX_290518_LETTER_EN Page 13 of 24
WARNING
PRODUCT MAY CONTAIN SHARP EDGES
Use care when servicing unit. Failure to do so could
result in minor personal injury.

4.5 Assemble the Legs and Rail
1. Support Legs
2. Unistrut bar clamps
3. Side Braces
4. Rail
a. If you are attaching the Support Legs (1) to the top or bottom
of a steel beam, use Unistrut bar clamps (2). To attach to the
top or bottom of a bar joist, use a thru bolt in the slot of the
bar joist.
b. Mount the Support Leg to the roof or to beams. The rst leg
will be approximately 3 to 4 ft (0,9 to 1,2 m) from the end of
the track or rail. Leg assemblies will need to be placed every
10 to 12 ft. and braced side to side using the appropriate
length side brace kit.
Note: Longer braces can be made out of ¾ in. (19 mm) EMT
conduit and attached to the leg using a Plymovent 8130-1011
leg/brace mounting kit. You should have at least one long
brace running front to back.
c. To calculate the leg length, determine the mounting height of
the rail, then subtract that dimension from the bottom of the
strut. Cut the aluminum square tube to this length.
Center a triangular foot and drill 2- 13/32 in. holes to attach
foot. Repeat for the bottom foot positioned perpendicular to
the rail (4). Attach the leg assembly to the strut on ceiling
using 3/8 in. strut hardware. Attach the side brace kit (3).
For multiple legs, turn the side braces perpendicular to the rail
and install one long front to back brace. Repeat for each leg
assembly.
d. To splice two rails, position the rail sections on saw horses.
Insert and center a splice plate (6) inside the rail (5), clamp in
place with a C-Grip and drill 2- 5/16 in. (8 mm) holes on top 2
in. from the joint and 4 in. apart.
On both sides, drill the rst 5/16 in. (8 mm) hole 2.5 in. (63,5
mm) from the top of the rail and 1 in. from the joint. Drill the
second 5/16 in. (8 mm) hole 2.5 in. (63,5 mm) from the rst
hole. Insert the bolts but leave them loose. Silicone the joint
and slide the other rail section onto the splice. Line up straight
in both directions and clamp. Drill the same holes on the
mating rail. Tighten the bolts in sequence - rst tighten the
top 4 bolts, and then the remaining 8 bolts on the sides for a
total of 12 bolts.
4
1
2
3
6
5
2.5 in.
2 in. 2 in. 4 in.
2.5 in 2.5 in
1 in. 1 in.
(50,8 mm) (101,6 mm)
(63,5 mm)
(63,5 mm)
(25,4 mm)
MAN_MAG_VSRX_290518_LETTER_EN Page 14 of 24

1
4.6 Mount the Rubber Seal
1. VSR prole
2. Rubber seal
3. Tool no. 0000102158
a. Turn the rail prole with the opening upwards.
The rubber lip seal can be easily installed with the Plymovent
VSR Lip Tool before hanging the rail from the support legs; or
you can install the lip after the rail is hung from the support
legs.
The rubber lip seals are directional and must be installed with
the inside bend towards the center of the rail or facing each
other. With the rail still on saw horses, install the rubber lip with
the bend facing inward. To make this easier, spray the lip and
aluminum channel with a soapy solution.
Start installing the rst 6 in. (15 cm) of rubber lip by hand using
a screwdriver and then position the lip tool on the rail to roll the
rest of the lip into the bend (1). Cut the ends at a 90 degree
ush with the end of the rail. Repeat for the other side.
4.7 Install the End Caps
Place each end cap on the rail and drill 4 3/8 in. (9,53 mm)
holes through the pre-punched holes in the end caps. Secure the
end cap with the provided hardware. Repeat for the back end
cap, but do not install until the rail is hung, so you can install the
crab/trolley.
For the front end cap (nearest the door), install the shock
absorber centered in the end cap (2), apply Blue Loctite on nuts
and tighten securely.
4.8 Hang the Rail and Connect to Duct
On the top of the rail, lay out 3/8 in. (9,53 mm) holes, for the
leg mounting feet locations, to match the distances between the
leg assemblies previously hung from the ceiling.
Pre drill these holes. Raise the pre assembled rail using multiple
scissor lifts or lifting mechanisms such as a chain fall. Position
rail under leg assemblies and attach with hardware.
For each of the duct connection locations along the length of the
rail, cut a 6 in. (15 cm) diameter hole in the top of the rail (3).
Apply silicone sealeant to the bottom ange of the duct
connector and attach with the provided self-drilling Tek screws.
Repeat this step if you are using multiple duct connections on
longer rails.
3
2
MAN_MAG_VSRX_290518_LETTER_EN Page 15 of 24
Note! The rubber seal must be angled inward.

7
6
4.9 Assemble and Hang the Hose and Grabber
1. Upper Hose
2. Metal Saddle
3. Balancer
4. Mid Hose
5. Lower Hose Assembly (Safety Disconnect Handle)
6. End Plate
Follow these steps to assemble and align the exhaust hose
assembly:
a. Mount the upper hose (1) to the trolley using a hose clamp.
b. Attach the upper hose to the short side (from the tab) of the
metal saddle (2). You may need to twist the hose to to have
the u-bend or loop positioned away from the vehicle in the 3
o’clock position if looking down at the crab trolley, with the
balancer at the 12 o’clock position.
c. Install the balancer (3) using the caribiner hook and safety
cable (8), and attach the Balancer Locking Cable (BLC) to the
trolley (9). Assemble the BLC using the length listed in the
Installation Table on page 10. Ideally, 6 in. (15 cm) of the
Balancer cable should be exposed when the Grabber nozzle is
connected to the vehicle.
Install the BLC so that it is on the back side of the balancer
and away from the adjustment locking clip. This will keep the
BLC from coming into contact and potentially breaking the
locking clip. The balancer snap hook should be oriented with
the catch or door of the hook on the same side of the balancer
as the locking clip. This will ensure that the BLC does not open
the snap hook, allowing the BLC to come loose. The BLC
attachment to the metal saddle snap hook should be opposite
of the catch or door so that it does not open it.
d. Attach the mid hose (4) to the long side of the metal saddle
with the supplied hose clamp. The mid hose is directional, so
install with directional arrow pointing up or with the airow.
e. With the balancer holding the hose all the way up cut the mid
hose at approx 4 ft (1,2 m) from the oor and attach to the
Safety Disconnect Handle (5) with the supplied hose clamp.
f. The height of the Grabber nozzle should be in. 14 to 18 in.
(35,5 to 45,7 cm) from the nished oor (7).
g. Secure the back end cap using the holes previously drilled (6).
3
1
2
4
5
9
8
MAN_MAG_VSRX_290518_LETTER_EN Page 16 of 24
WARNING
PRODUCT MAY CONTAIN SHARP EDGES
Use care when servicing unit. Failure to do so could
result in minor personal injury.

3
2
1
TAILPIPE REDUCER
ATTENTION
Please ensure that the position of the tailpipe
connector meets EN 1846-2, which indicates the
minimal distance from tailpipe connector to the road
surface (diers per type of vehicle).
Example of Tailpipe Connector on Truck Body
4
5
Example of Tailpipe Connector on Truck Body
with Tailpipe Reducer
ATTENTION
To ensure the conical tailpipe adaptor and/or tailpipe
connector are mounted rmly to the vehicle chassis,
it’s recommended that you use the tailpipe bracket.
4.10 Install the PC-500 Pressure Switch
Please refer to Wireless Manual (article #100716) for
installation.
MAN_MAG_VSRX_290518_LETTER_EN Page 17 of 24
5 MODIFYING THE TAILPIPE
5.1 Install the Tailpipe Connector
1. Distance exhaust pipe-truck body
2. Tailpipe
3. Conical tailpipe adapter
4. Tailpipe bracket
a. The distance between the middle point of the tailpipe and the
body of the vehicle (1) must be at least:
- 3 in. (75 mm) in all directions when using a 3 in. system
- 4 in. (100 mm) in all directions when using a 4 in. system
- 5 in. (125 mm) in all directions, when using a 5 in. system
This should be checked before the conical tailpipe connector is
attached.
b. The end of the tailpipe (2) must be cut in a 90° angle and all
sharp edges must be ground o.
c. The conical tailpipe adapter (3) is positioned on the tailpipe.
When attached the minimum space between the tailpipe
connector and the body of the vehicle should now be at least
0.6 in. (15 mm) from the top and both sides of the tailpipe
adaptor.
d. The tailpipe support/hanger (4) must be positioned within 20
in. (500 mm) from the exhaust pipe end (2). If not, the
optional tailpipe bracket must be installed. (see: option:
installing the tailpipe brackets)
e. The exhaust pipe must be in a 90° angle to the truck body
with a max inclination of 5°.
f. The distance between the exhaust pipe and the wheel must be
a minimum 12 in. (300 mm).
g) The tailpipe adapter shall be installed ush with the
body of the vehicle in accordance to NFPA1500 (5). Make sure
you meet EN-1846-2 requirements related to minimal
clearance to the road.
5.2 Modify the Tailpipe
Option: Installing the Tailpipe Reducer
In case you want to install a 5 in. (125 mm) conical tailpipe
adapter and the vehicle uses a 4 in. (100 mm) tailpipe, you will
have to install a tailpipe reducer. The tailpipe reducer is a part
that adapts the 4 in. (100 mm) tailpipe into a 5 in. (125 mm)
tailpipe so the conical tailpipe adapter can be installed. The
tailpipe reducer is positioned over the existing tailpipe and xed
using a 4 in. (100 mm) tailpipe clamp. Product number: Refer to
your FIRE Price list for specic product numbers.

WARNING
The Balancer is delivered under tension. Be careful
when unwinding this balancer.
WARNING!
After the Safety Disconnect has released please
check if all spring blocks in the product are free of
damage and functioning correctly. Any damaged
parts should be replaced and the correct functioning
should be veried. If the Safety Disconnect is not
functioning correctly, it can potentially cause
damage to person or property.
Image:Tailpipe reducer
Image:Tailpipe support bracket
MAN_MAG_VSRX_290518_LETTER_EN Page 18 of 24
5.3 Check the Balancer Tension
The balancer is delivered from the factory with pre-tension
already set. After every component of the system is installed,
you may need to adjust the balancer pre-tension to its nal
setting, to ensure that the balancer is functioning properly.
Increase or decrease the spring tension until the rubber stop
loosely hits the balancer housing and cable is retracted.
It’s possible the balancer tension needs to be ne-tuned after
the total system is installed and a test run is done.
5.4 Safety Disconnect Handle
Function:
The safety coupling disconnect opens in case of missue of the
systemor failure of the disconnection and can allways be
re-used.
Adjustment:
The Safety Disconnect Coupling is delivered completely
assembled with a preset tension. The standard setting on
delivery gives you a release force at 450N and a reconnection
force of 150N.
Release Force:
You can adjust the safety coupling disconnect by using dierent
springs available from Plymovent. These are not included, so
please contact your Plymovent authorized distributor.
5.5 Tailpipe Modication Options
Tailpipe Reducer
The tailpipe adaptor is used when an exhaust tailpipe needs to
be converted from a smaller size to a larger size to allow the
conical tailpipe adapter to be installed.
New Art. # Old Art. # Description
00000113613 90365-1011
Tailpipe Reducer, 5 in. (127
mm) Male to 4 in. (101,6
mm) Female w/clamp
Tailpipe support bracket
The tailpipe support bracket can be used for various dimension
exhaust tailpipes and ensures a secure connection between the
tailpipe and body / chassis. In some cases, you may need to
divert the exhaust ow from the tailpipe to the side of the
vehicle. The Magnetic Grabber®connector can then be installed
to this modication.
When a tailpipe modication is needed, Plymovent recommends
you consult the manufacturer of the vehicle.
As an example, the image on the next page shows the
Plymovent tailpipe support bracket being used with a 3rd party
tailpipe reducer pack. This ensures a support a correct and
sturdy installation of the Magnetic Grabber®connector.
New Art. # Old Art. # Description
00000105131 90370-1011 Tailpipe Support Hanger

TAILPIPE REDUCER
MAN_MAG_VSRX_290518_LETTER_EN Page 19 of 24
Tailpipe reducer packs
The tailpipe reducer pack enables vehicles with dierent tailpipe
sizes to connect to the Plymovent Magnetic Grabber tailpipe
connector.
This product can be used in combination with the Magnetic
Grabber tailpipe bends as well as direct onto the Magnetic
Grabber tailpipe connector. The tailpipe reducer pack allows a
wide range of exhaust pipes to connect to the Plymovent
system.
New Art. # Old Art. # Description
00000113613 90365-1011
Tailpipe Reducer, 5 in. (127
mm) Male to 4 in. (101,6
mm) Female w/clamp
00000115892 702014-K
Tailpipe Reducer, 5 in. (127
mm) Male to 3.5 in. (88,9
mm) Female w/clamp
0000105131 90370-1011 Tailpipe Support Hanger

6 USER AND MAINTENANCE INSTRUCTIONS
6.1 Operating the Magnetic Grabber
6.1.1 Connecting the Magnetic Grabber
Please ensure that, on the side of the vehicle were the system is
installed, no persons are present in an area of 3 feet (1 m)
under and / or around the VSRX system and /or between the
vehicle and the entry / exit door when the vehicle exits the
building. This way possible injuries can be avoided by a possible
backwards motion of the Grabber in the direction of the station
and park position.
When a vehicle returns to its bay the Magnetic Grabber nozzle
can easily be attached to the conical tailpipe adapter.
The Magnetic Grabber nozzle must be placed straight onto the
conical tailpipe adapter, but to connect it is easiest to rst attach
the top of the Magnetic Grabber and then press down on the
safety disconnect in order to attach the lower part of the
Magnetic Grabber.
The conical design of the connection surface ensures safe and
easy positioning.
6.1.2 Disconnecting the Magnetic Grabber
a. Automatic disconnect - The Magnetic Grabber nozzle will
disconnect automatically when the vehicle exits the bay.
b. Manual disconnect - To manually disconnect the Magnetic
Grabber nozzle; hold the safety disconnect with two hands
and push it downwards.
6.1.3 Cleaning Instructions
To ensure a good magnetic connection at all times, you will need
to ocassionally clean a few components:
a) Make sure you keep the connection surface of the conical
tailpipe adaptor clean of soot and other contaminations.
b) Using a damp cloth (rubbing alcohol, degreaser, or other
fast-evaporating solvent), wipe the connection surface of the
Magnetic Grabber®.
d) Using a damp cloth, wipe the entire vertical face/sealed
ange of the conical tailpipe adapter. Diesel soot build-up
may occur when idling or driving at slow speeds.
6.2 Inspection and Maintenance
We recommend that you add the following activities to your
truck cleaning schedule:
1. Check if the magnets on the Magnetic Grabber are all in place
and clean.
2. Check if the conical tailpipe adaptor is clean and there are no
obstructions that can prevent the magnets from positioning
themselves on the product.
3. Remove the hose assembly from the balancer and check the
hose for any defects.
4. Make sure the metal saddle and Magnetic Grabber are still
xed tightly to the hose.
5. Check to make sure the trolley runs smoothly through the rail
and correct stop at the end-stops.
6. Clean the inside of the rubber lip.
MAN_MAG_VSRX_290518_LETTER_EN Page 20 of 24
ATTENTION!
Service and maintenance only to be done by qualied
and trained persons (in EU according to TRGS 554.)
Use sucient safety gear and guards when working on
a higher level than 6.6 ft. (2 m)
Only carry out service and maintenance when the
system is fully disconnected from main circuit.
Be sure no vehicle can enter the station/bay when
carrying out service/maintenance.