PM FBWM SAM IFJ User manual

9500254 v1.0
publ. 10/15/18
FBWM SAM IFJ
FLAT BRACKET VIDEO WALL MOUNT
FOR SAMSUNG IFJ LED SERIES
INSTALLATION GUIDE
premiermounts.com | p. 800.368.9700 | e. [email protected]
500 W Central Ave, Suite A, Brea, CA 92821 USA

Installation Guide
www.premiermounts.com | North America 800.368.9700 | International [phone]www.premiermounts.com | North America 800.368.9700 | International [phone]
Page 2
METHOD 1 METHOD 2
Assemble the mount before installing into
place (for single unit or small array).
Install piece by piece on a located wall (for
multiple or large video wall array).
CAUTION STATEMENTS
1. READ ALL STEPS WITHIN THIS MANUAL BEFORE INSTALLING THE MOUNT. SAMSUNG IFJ LED
SERIES INSTALLATION GUIDE MUST BE READ IN CONJUNCTION FOR SUCCESSFUL
INSTALLATION. ANY QUESTIONS? CALL PDS.
2. FRAME MUST BE PLUMBED, SQUARED, LEVELED, X, Y, AND Z ALIGNED PRIOR TO INSTALLATION OF
ANY DISPLAYS.
3. ALL LED CABINETS MUST BE POWER ON TESTED PRIOR TO ANY INSTALLATION.
4. PDS RECOMMENDS THE HANDLING LED CABINETS BY AN INDUSTRY QUALIFIED PROFESSIONAL.
5. PDS IS NOT RESPONSIBLE FOR DEFECTS, MISUSE, OR IMPROPER HANDLING OF THE LED CABINETS.
Tools for Installation:
00.0 o
Spool of
colored strings
Anti-Static
Gloves
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone] Page 3
Imperial
(Inches)
Metric
(Milimeters)
X
1 Wide 31.718 805.6
2 Wide 63.466 1612.1
3 Wide 95.214 2418.5
Y
1 High 17.828 452.8
2 High 35.686 906.4
3 High 53.545 1360.1
4 High 71.403 1813.6
5 High 89.261 2267.2
VIDEO WALL DIMENSIONS AND MOUNTING LOCATIONS
Determine the overall dimensions of the mount by
using the table within this page.
For example: 3X3 array would be 95.22” x 53.54” but
larger array i.e., 9X9 would consist of multiple rails for
an overall of 285.65” x 160.66”.
1" HANG
LOCATION
48" APART
HANG LOCATION
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
Page 4
PRE-INSTALLATION
Nylon Washer
Steel Washer
M5 x 10mm
Comb Screw
M6 x 35mm
Socket Screw
Default Position and aligment
notch for wall leveling bracket
Floating Adjustment
Assembly (or “Floaters”)
Even array - e.g. 6 Wide
Odd array - e.g. 3 Wide
Identifier for the
top or bottom
horizontal rail
UNUSED
FLOATER
LOCATION
1/2”-13 x 1.5”
Bolt With Hole
To keep flange
straight during
SHIPPING.
NOT required for
INSTALLATION.
Wall Leveling
Bracket
Floaters must be install on each corner of the entire array and every other location (indicated by the notch).
2nd 3rd1st every otherand
corner location
every other column
1. Identify the square cutout with a V-notch to determine
the placement and direction of the Floating Adjustment
assembly (or “ ”) shown on above.
2. Install on every other column and corner locations of the
mount.
3. Fasten using (2) M5 x 10mm Comb Screw, (2) Nylon
Washers, (2) Steel Washers.
4. Install 1/2”-13 x 1.5” Bolt with Hole onto each threaded
extrusion and a M6 x 35mm Socket Screw for ease of
installation in sequential step.
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
1
2
Page 5
Horizontal
Rail
M5 x 8mm
Flat Head
Install the Vertical and Horizontal Rails together using (4) M5x 8mm Flat Head Screw per.
1. Determine the desired location by calculating the height of the pre-mounting hang location using
the table on page 3.
2. Use any commercially available hardware to temporary hang the mount.
METHOD 1
Support
Screws
To temporary
hang the mount
48” apart
Vertical Rail
(center)
Vertical Rail
(left and right)
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
3
Page 6
1. Place a level on top of the mount and reinstall or adjust the support screws if necessary.
2.
using 1/4” x 5” Hex Lag and 1/4” Washer.
3. Maintain a 1/8” minimum gap from the anchor plate and the rail when anchoring.
4. Install the remaining mounting locations while keeping the mount leveled.
DIGITAL LEVEL
00.0 o
1/8” min. gap
Clearance
1/4” Washer
1/2”-13 x 1.5”
Bolt With Hole
Wall Anchor
Plate
Vertical Rail
1/4” x 5” Hex
Lag
Support Screw
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
1
Page 7
00.0 o
DIGITAL LEVEL
WALL WALL
1. Install (2) 1/2”-13 x 1.5” Bolt with Hole onto the threaded extrusion.
2.
3.
using 1/4” x 5” Hex Lag and 1/4” Washer.
4. Maintain a 1/8” minimum gap from the anchor plate and the rail when anchoring.
5. Level, Square, Plumb.
6. Install the remaining lag bolts, washers, and wall anchor plate.
METHOD 2
1/8” min. gap
Clearance
1/4” Washer
1/2”-13 x 1.5”
Bolt With Hole
Wall Anchor
Plate
Vertical Rail
1/4” x 5” Hex
Lag
Wall Anchor PlateWall Anchor Plate
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
2
3
Page 8
Vertical
Rail (Left)
Horizontal Rail
(Mounted)
1. Securely fasten each Vertical Rail to a mounted Horizontal Rail using (2) M5 x 8mm Flat
Head Screw per end.
2. Fasten the Lower Horizontal Rail but do not anchor until the mount is perfectly square. See
sequential step.
ASSEMBLE THE LOWER SECTION OF THE MOUNT
Install a few support screws (commercially available hardware) to temporary hold the lower
section in place prior to final mounting location.
Vertical Rail
(Right)*
M5 x 8mm
Flat Head
Lower
Horizontal Rail
*Single unit configuration shown above. Left and right rails are for the entire array.
Vertical Rail
(Center)
Installation is not finished within this step. After leveling the vertical brackets,
secure the bottom horizontal to the wall. See step 8 for additional detail.
Support
Screws
Do Not Anchor Prior to
Final Mounting Location
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
4
Page 9
0XOWLSOH8QLW&RQ¿JXUDWLRQ
1. Hang and position the second Horizontal Rail side by side.
2. Place a support screw while maintaining a leveled horizontal rail to temporary hold in place.
3. Install (2) Attachment Plate and fasten together using (4) M5 x 8mm Flat Head Screw for each rail.
4. Install the remaining Vertical Rails (center) using (4) M5 X 8mm Flat Head Screw.
5. Install the lower section of the mount as the steps above.
To extend the width of the unit, follow the steps below.
Extend Horizontally
Horizontal Rail
(1st unit)
Horizontal Rail
(2nd unit)
DIGITAL LEVEL
the seems between
two units 00.0 o
Attachment
Plate
M5 x 8mm Flat
Head Screw
Vertical Rail
(center)
Figure 1
Figure 2
Insert a support
screw temporary
hang the mount
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
FBWM SAM IFJ
www.premiermounts.com | North America 800.368.9700 | International [phone]
5
Page 10
Extend Vertically
0XOWLSOH8QLW&RQ¿JXUDWLRQ
1. Position multiple units adjust to each other.
2. Joint the units together using multiple Attachment Plate and fasten using
(2) M5 x 8mm Flat Head Screw per.
3. When extending the height of a video wall array, the middle row shares the
Horizontal Rail between two units. Additional Horizontal is not required.
To extend the height of the unit, follow the steps below.
No additional
Horizontal Rail
No additional
Horizontal Rail
Required.
FBWM SAM IFJ
premiermounts.com | p. 800.368.9700 | e. [email protected]