poedagar DELUXE CLASSIC Series User manual

DELUXE CLASSIC™ SERIES
INSTRUCTION MANUAL (EN)
INTRODUCTION
Thank you for purchasing a Peodagar mepiece. The
Poedagar Deluxe Classic™ is a quartz watch and requires an
LR626 1.5V alkaline baery in order to funcon. The baery
generates a small electrical charge which is applied to the
quartz crystal, causing the crystal to oscillate at a precise and
constant frequency of 32,768 mes per second. The signal
generated by these oscillaons is used to drive the second-
hand and causes it to ck once every second. The second
hand is geared to turn the minute-hand and the hour-hand.
Before using your watch, please familiarise yourself with the
following instrucons.

SETTING THE TIME AND DATE
The Deluxe Classic™ features an hour-hand, a minute-hand, a
second-hand and a date calendar. The minute-hand, hour-
hand and date are adjusted by using the crown. The following
sequence is the recommended method for adjusng the me
and ensuring your watch funcons correctly, displays the
me accurately and that the gears suer no excessive wear.
1. Wait for the second-hand to reach the 12 o’clock
posion.
2. When the second-hand reaches the 12 o’clock
posion, gently pull the crown out to the rst click.
3. Turn the crown an-clockwise (towards you) to adjust
the date. Stop once the date displayed is the day
before the intended date.
4. Pull the crown out to the second click.
5. Rotate the crown clockwise to adjust both the hour-
hand and the minute-hand. Rotate the crown
clockwise unl the hour hand passes the 12 o’clock
mark and causes the date to change to the intended
date. The me shown at this point is the AM of the
intended day.
6. Connue to rotate the crown clockwise unl the
hour-hand is poinng to the intended hour,
remembering that it will need to pass the 12 o’clock
mark again before the me displayed refers to the
PM.
7. Once the hour-hand is poinng towards the intended
hour, connue to rotate the crown clockwise unl the
minute-hand is poinng to the minute aer intended
minute.

8. Wait unl the actual me reaches 59 seconds past
the intended minute and gently push the crown back
in fully as the me reaches 60 seconds past the
intended minute.
9. The me should now be set precisely to the second,
minute, hour and date.
Turning the crown in the opposite direcon to the direcon
recommended above for the dierent crown pin posions
can cause the gears to suer unnecessary wear but can be
done slowly and by a small amount (to correct a slight
maladjustment for example) without having a signicant
eect.
We do not recommend changing the me when the watch is
operang between the displayed mes of 9pm and 3am.
Doing so regularly may cause unnecessary wear to the
mechanism.
CALENDAR MECHANISM
Because of the way movements are made, it is almost
impossible for the day and date on a quartz watch to change
at exactly 12am.
When the date changes, a small prong engages the date
wheel and pushes it forward, causing it to rotate and display
the next date. This happens over the course of a few hours.
In order for the watch movement to be able to change the
date displayed, more power is required than the amount
used to make the hands move. The watch movement has to
first accumulate the amount of power required for a small
motor to rotate the date wheel. In order to accumulate

sufficient power, the mechanism responsible for the date
change is engaged during the hours preceding and following
midnight.
The day and date may not be displayed correctly for several
hours while the mechanism is engaging. This is normal and is
not a fault.
Due to the workings of the mechanism described above,
changing the date on your watch between the displayed
hours of 9pm and 3pm is not recommended and doing so
could damage the movement of the watch.
ADJUSTING THE BRACELET LENGTH
The Deluxe Classic™ is supplied with a stainless-steel
bracelet, the length of which can be adjusted by removing or
adding bracelet links. Only links with two pins can be
removed. The watch is supplied with all removable links
aached to the bracelet. A link pin removal tool (not
supplied) is required to remove the bracelet links. Please
follow the instrucons provided with the pin removal tool or
take the watch to a watchmaker or watch repair shop to
remove the links.
REPLACING THE BATTERY
The Deluxe Classic™ features a snap-back case cover. A watch
case back removal tool (not supplied) is required to access
the baery. Please follow the instrucons provided with the
watch case back removal tool or take your watch to a
watchmaker or watch repair shop to open the case and
replace the baery. Ensure the baery is inserted with the

correct polarity and that the back gasket is fully intact and
correctly posioned before replacing the case back and
sealing the case.
WARRANTY & GUARANTEE
The Deluxe Classic™ is covered by a 1-year manufacturer’s
guarantee. Please register your guarantee at
www.poedagar.co.uk within 30 days of purchase.
A label with a unique serial number is axed to the inside of
the case back. Removing this label will void your warranty. In
the unlikely event that the watch case back needs to be
replaced with a new case back, please retain the original case
back. The original case back will need to be returned with the
watch and with the serial number intact for any claim made
against the manufacturer’s guarantee or 5-Year Extended
Warranty to be honoured. Further informaon is available at
www.poedagar.co.uk.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
Old electrical equipment can be recycled and should now be
marked with a crossed-out wheeled bin symbol. Please do
not throw any electrical equipment (including those marked
with the crossed out wheeled bin symbol) in your bin. Please
speak to your retailer if you require further informaon.
© 2023 Tektonite Ltd. or its aliates. All rights reserved. The “Poedagar logo” trademark is
used under licence.