Poolweb DIAPER DEPOT SS3300 User manual
31 1/2" A.F.F.
Open
Side View
27 1/9"A.F.F.
33 1/4"
23 1/8" A.F.F.
Changing Arm
Closed
23 1/8" A.F.F.
6"
DIAPER DEPOT®VERTICAL CHANGING STATION
Installation Instructions (IMPORTANT: Keep for future reference – Read Carefully)
4 Machine Bolts
4 Wood Screws
1 Depot
(side view)
Determine which mounting hardware will be used:
Set A – Wood Screws for mounting into wood studs
Set B – Toggle Bolts for mounting into metal studs
or sheetrock/tile wall (a clearance or 3-1/2" is
required behind the wall for the toggle to expand).
Manufacturer strongly recommends installation
as shown. When installed at 23-1/8" A.F.F., as
depicted, along an accessible route, the Diaper-
Depot meets the following requirements of the
ADA accessibility guidelines, when applicable:
4.4.1 Protruding objects (closed unit)
4.2.5 Forward reach
4.2.6 Side reach
4.23.3 and 4.23.7 fixtures
4.27.4 Hand operation
4.32.3 Knee clearances at counter
4.32.4 Height of counters
Remove backing from decal and secure it to the outside
of the restroom door or other highly visible location.
What you will need:
• Measuring Tape
• Stud Finder
• Screwdriver
• 7/32" Drill Bit (regular & masonry)
• 1/8" Drill Bit (regular & masonry)
• 1/2" Drill Bit (regular & masonry)
• Drill
• Pencil
For Technical Assistance, Call SSC, Inc. (Safe-Strap Co.) 1-800-356-7796
or visit our website at www.diaperdepot.com
1. Using the adjacent diagram as a guide,
mark the four mounting points on the
wall. Using 16" stud walls, mark the
top two holes 49-5/8" above the floor
and the lower two holes 33-5/8" above
the floor. Measure the exact distance
between the holes you are using from
the back of the depot, and transfer
these measurements onto the
corresponding wall lines.
2. A. For Wood Studs: Drill through the
ceramic tile or surface finish at the
marked hole locations with a 7/32"
masonry bit until you hit the stud,
then change to a 1/8" regular bit
to complete the hole through the stud.
B. For Metal Studs Or Underlying Surface of
Concrete Block: Drill at the marked hole locations
with a 1/2" masonry drill bit. You must allow a
minimum 3-1/2" of inside wall space for toggles
to turn. Insert and tighten all four toggles.
3. Place a finishing washer first and then a fender washer over each screw.
A. For Wood Studs — Lift the depot
in the open position and align the wood
screws into the upper pre-drilled holes.
Tighten each screw until the unit is held
firmly in place. Repeat installation of the
lower screws and tighten all screws until
the unit is held securely.
B. For Metal Studs Or Underlying
Surface Of Concrete Block — Lift
the depot in the open position and align
mounting holes with pre-drilled holes.
Insert machine screws with washers into
pre-drilled holes. Tighten each bolt until
the unit is held securely in place.
4. Fill liner dispenser with liners. For replace-
ment liners please call 1-800-356-7796.
A. Insert toggle in hole
drilled
B. Pull ring and push cap
lightly against wall
C. Snap off strap D. Install unit using
screws and
washer supplied
49 5/849 5/8
33 5/833 5/8
Floor (not drawn to scale)
For YourConvenience
We Provide...
Diaper-Depot
Changing Station
Broughtto you by:
Safe-Strap Company, Inc.
1-800-356-7796
4 Fender
Washers
4 Toggles 4 Finished
Washers
1 Mounting Template
1 Decal
Diaper-Depot VerticalInstallation Template
Plantilla de instalacion vertical Diaper-Depot
For Use With Diaper-Depot VerticalInstallation Instructions ONLY
Para usar SOLO con las instrucciones de instalacion vertical de Diaper-Depot
1. Locate the studs in your walls to determineif they are 16 inches apart.
Situe los tacos en las paredes para determinar si estan separados por 16 pulgadas.
2. Attach this Installation Templateto the wall. If your studs are 16 inches apart,line
up the centers of the squareson this template with your wall studs.
Ponga la plantillade inst alacion en la pared. Si los tacos estan separados por 16
pulgadas,alinee los centros de lasescuadras de esta plantilla con los tacos de la
pared.
3. Make surethe bottom marked edge of th is template is 28-1/8 inches from the floor.
This will assurethat your Diaper-Depot will meet ADAguidelines,where
applicable.
Cerciorese de que el borde marcado inferior de la plantilla este a 28-1/8 pulgadas del
suelo.Esogarantizara que suDiaper-depot cumplira las normas ADA,en la
medida en que sean aplicables.
4. Follow remaininginstructionson your Diaper-Depot Installation Instructions,
included with your Diaper-DepotChangingStation.
Siga los pasosr estantes de las instrucciones de instalacion del Diaper-Depot,
incluidas en el puesto de cambio de Diaper-Depot.
Fromthis dotted line to the floor should measure 23-1/8 inches.
Desdeesta linea de puntos al suelo debe medir 23-1/8 pulgadas.
WARNING
Never leave child unattended
Designed for infants only. Age up to 3.5 years
and weighing less than 50 lbs.
Keep one hand on the child at all times
Avoid serious injury from falling or sliding out
Always use restraint system
Please be advised that parcels or accessory items, or both,
placed on the unit may cause the unit to become unstable.
The maximum recommended weight for this unit is 50 pounds.
Excessive weight placed on the unit may cause a hazardous
unstable condition to exist.
All assembly parts must be sufficiently tightened at all times.
Screws cannot be loose, as the child’s body parts or clothing
(such as straps, necklaces, ribbons, dolls, etc.) may get pinched.
This may cause a suffocation hazard.
Be aware of the risk of open fire and other strong heat sources,
such as electric heaters, gas stoves, etc. in the immediate
surroundings of the diaper changing station
Wipe down regularly with mild cleansers
!
Adequate Use of Restraint System
• Lay child on their back in the bed portion of the diaper changer
• Place the restraint belt around the child
• Insert the two ends of the buckle into each other until you hear a click
• Give a slight tug to make sure the buckle is locked
• Use the adjustment glider to tighten the restraint securely around the child
