pottery barn kids GRAHAM User manual

Date:2016-May-11 Page1of7
Rev:






pottery barn kids


GRAHAM TODDLER BED CONVERSION KIT

www.potterybarnkids.com

Date:2016-May-11 Page2of7
Rev:


WARNING ENTRAPMENT/STRANGULATION
HAZARD:
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and assembly instructions could result in serious injury or
death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
Read all instructions before assembling toddler bed. KEEP INSTRUCTIONS FOR
FUTURE USE.
DO NOT use a water mattress with this toddler bed.
Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
DO NOT place bed near windows where cords from blinds or drapes may strangle a child.
Do not place items with a string, cord, or ribbon around the child’s neck, such as hood
strings or pacifier cords.
Do not suspend strings over a toddler bed or attach strings to toys.
If refinishing, use a non-toxic finish specified for children's products.
If included, always use guardrail(s).
CAUTION: ANY MATTRESS USED IN THIS TODDLER BED MUST BEAT LEAST 27 ¼" (69
CENTIMETERS) BY 51 5/8" (131 CENTIMETERS) WITH ATHICKNESS NOT EXCEEDING 6"
(15 CENTIMETERS) BUT AT LEAST 4” (10 CENTIMETERS).
THIS BED IS FOR CHILDREN OVER 15 MONTHS OFAGE WEIGHING NO MORE THAN 50
POUNDS (22.7 kg). 04-000032-7
IMPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Do not remove warning labels from the crib. Labels are permanent and not designed to be removed.
PRE-ASSEMBLY:
Remove all parts and hardware from the box and place them on a carpet, or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly in not recommended. Power tools can damage hardware and split
wood.

Date:2016-May-11 Page3of7
Rev:
PARTS INCLUDED:
(N). GUARDRAIL (1x)
CRIB PARTS (Sold separately):
(A). CRIB END (2x)
(B). CRIB SIDE (1x)
(C). MATTRESS BASE (1x)
HARDWARE REQUIRED
(D) Allen key with ball tip
- 2x (O) Allen Bolt M6x1-1/2” -3x(P) End Cap M6 -2x
HARDWARE REQUIRED (From Crib):
(E) Long Allen Bolt M6 x 2-3/8” - 2x (F)Medium Allen Bolt
M6x3/4”-4x (H) Half moon washer 1/4” x24mm – 2x

Date:2016-May-11 Page4of7
Rev:
Assembly Instruction Steps:
1. Take out the Magnetic Décor cover (M) from the Crib End (A).
2. Remove the (B) by following these steps below.
-Remove (E) as shown at Picture2‐1
- Loosen the 2 front bolts (G) to remove (B) easier as shown at Picture2‐2
Note: Keep (E&H) aside for later use on toddler bed assembly.
Picture2‐2
Picture2‐1
Picture2‐1
LOOSEN (NOT REMOVE)

Date:2016-May-11 Page5of7
Rev:


3. Note: The mattress base (C) should be at the lowest level (Level 1) for a Toddler bed. If your mattress
base is not at the lowest level, follow instructions below to change.
a. Remove the matress base from the high position by removing the 4 bolts (F)
b. Attach the matress base to the lowest level (Level 1) by re-using the above bolts (F)



















4. Attach the guard rail (N) to the Crib End (A) as shown below.
*Tip: See Image A for ease of assembly. Do not over tighten.
























F 4x
E 2x
H 2x
O 1x
Image A

Date:2016-May-11 Page6of7
Rev:


5. Slowly turn the toddler bed kit upright.
6. Check alignments and fully tighten all connections at this time. Do not over tighten.
7. Attach (O&P) to Crib End (A) as shown below.
.
8. Attach the Magnetic Décor cover (M) into the Crib End (A).
O 2x
P 2x

Date:2016-May-11 Page7of7
Rev:


9. Assembly is now complete.
10. Place the assembly instructions back into the envelope mounted on the mattress base for future reference.
CARE INSTRUCTIONS:
‧ Dust often using a clean, soft, dry lint-free cloth.
‧ Blot spills immediately, and wipe with a clean, damp cloth.
‧ We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
‧ If the crib is to be stored, store in cool dry place and carefully package all original hardware to protect from loss
or damage.
‧ Check fasteners periodically for tightness DO NOT over tighten. This may cause distortion or breakage.
‧ Parents should ensure a safe environment for the child by checking regularly, before placing the child in the
product, that every component is properly and securely in place.
Thank you for your purchase
Stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181








