pottery barn kids CHARLIE QUEEN BED User manual

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 1 of 6
pottery barn kids
CHARLIE QUEEN BED
www.potterybarnkids.com

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 2 of 6
Important Safety Instructions:
•Please read all instructions carefully before assembling this Bed.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep these instructions for future use.
•Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work
surface, as this will avoid damaging the parts during assembly. The shipping box provides an ideal
work surface.
•To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or
contents of the shipping carton until assembly is complete.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
•The use of power tools to aid in assembly is not recommended. Power tools can damage the
hardware and split the wood.
Parts Included:
(A) Headboard (1x)
(B) Footboard (1x)
(C) Side rails (2x)
(D) Slat roll (1x)
(E) Center support rail (1x)
(F) Support leg (3x)
Hardware Included:
(G) Flat head wood screw
4x30 mm –28x
Tools required (not included):
Philips Head Screwdriver
E
C
F
C
C
B
A
D

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 3 of 6
Assembly Instruction Steps:
1. Attach (C) to (A) & (B) by inserting the pre-fixed hooks into the corresponding slots as shown below.
Apply downward pressure and ensure connections are secure.
2. Attach (F) to (E) as shown below.
A
B
C
C
E
C
F
F

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 4 of 6
3. Attach the assembled Center Support Rail (E) with Support Leg (F) to the Headboard (A) and
Footboard (B) by sliding it onto the bed fitting, as shown below.
Adjust the levelers underneath each support leg (F) to keep the whole bed level
NOTE: The Bed can be used with or without a trundle. The position of center rail (E) will be
determined depending on which option you choose.
a. Option 1 –Without a Trundle: center rail attach to the metal bracket at the middle of the
Headboard (A) and Footboard (B).
b. Option 2 –With a Trundle: center rail assembled at one side of the Headboard (A) and
Footboard (B). Follow below steps:
- Remove the metal bracket on headboard and footboard by unscrew the wood screw
- Align the metal bracket over the pre-drilled holes at one side of the headboard and footboard and
then secure again with original wood screw
- Attach the center rail to the metal bracket
E
C

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 5 of 6
4. Lay (D) onto inner ledge of Side Rails (C) and fasten each slat with (G) and Phillips head screw
driver (not provided) as shown below.
E
C
G
28x
D
C
C
G

Date: 2016-Jan.-16
Rev: 2016 03 11 Page 6 of 6
5. Assembly is completed. Carefully slide Charlie Trundle under the bed.
Option 1 Option 2
Care Instructions:
•Dust often using a clean, soft, dry, and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp cloth.
•We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our
lacquered finish.
•Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thank you for your purchase
Stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181