PotteryBarn Trigger Lift Cantilever umbrella User manual

Trigger Lift Cantilever umbrella
Instruction Manual
Patented product
Step 1
Secure your cantilever umbrell
a to the base,
See separate base instructions
.
Note
: For safety reasons 2 persons
are required to co-lift the um
brella to
the base.
Step 2
Spueeze the Trigger and push up
to
the first or second position.
Crank the handle clockwise to o
pen
your umbrella.
Step 3
Once your umbrella has been op
ened
you can now squeeze the trigge
r and
push up to the highest positio
n . The
fully open position will have
the canopy
parallel to the ground.
WARNING
Do not crank in counter clockwis
e
direction as the umbrella will g
o up
but not hold and suddenly will c
ome
down.
WARNING: Do not leave your
in the open position d
uring wind or rain storms. Close
your umbrella when not in use.
This umbrella must be used with
the
base designe
d for it.
umbrella

Step 4
To rotate the umbrella,you must
be using
an umbrella base with a 360 ro
tation feature.
You would simply step on the p
edal
and rotate to the desired posi
tion.
Step 5
To tilt the umbrella you would
squeeze the
trigger and bring down the umb
rella to one
of the 3 holes for tilting.
Step 6
To close the umbrella , squeez
e the Trigger
again and bring down to the fi
rst or second
position . Crank the umbrella
counter clockwise
to close .
Re-Squeeze the trigger and bri
ng all the way
down .
Thank you for your purchase
Stores/ catalog/ www. potterybar
n.com
Care Instructions
· rush to remove dirt and dust
· For spot cleaning , sponge lig
htly with
a solution of mild soap and wa
rm water.
Storage instructions
·
Store in a dry, covered area whe
n not in use
· To prevent mildew, be sure the
umbrella fabric is completely
dry before storing. Store indo
ors when not in use or during
periods of of inclement weathe
r.
· Cover during storage or when n
ot in use using a proper
outdoor protective cover allow
ing adequate ventilationwithout
trapping moisture .
· Do not cover with plastic or s
imilar materials that will trap
moisture. Pottery Barn umbrell
a covers are vented and can
be used.

Assembly instructions
Tiles not included
Patented
product
Thank you for your purchase
Stores/ catalog/ www.potterybarn
.com
Tools Required:
Wrench (5mm) (1x)
Wrench (6mm) (1x)
Bolt (M8x30mm) (4x)
Bolt (M8x13mm) (4x)
Cover (1x)
Cover ring (1x)
Rotation mechanism (1x)
Steel plates D (1x)
Parts Required:
Hardware Enclosed:
Stem (1x)
A
C
D
E
F
Tile (4x)
(Separate pack)
G
Steel plates E (1x)
a
b
c
d
Assembly Instructions:
1.
Cross the steel plates (D) and
(E) as shown on figure.
2.
Put on the rotation mechanism (C) and secure
to the steel plat es with steel bolts (c) of
M8X30mm by wrench (6mm).Do not tighten the
bolt until all 4 bolts are attached
3.
Attach on the stem (F) and se cure with
steel bolts (d) M8X13mm
by wrench (5mm). Do not tighten the bolt
until all 4 bolts are attached
4.
Insert the cover (B) to the s tem,
then put on the 4 Tiles(G).
5. Insert the cover ring (A) to
the bottom of
umbrella pole first for easy
installation purpose,
and then attach the umbrella
pole to the stem.
D
E
B
A
B
G
b
c
C
a
F
d
Tightening knob
(1x)
H
H
6. After umbrella pole has been
inserted into base,
Part-H must be tightened to
prevent umbrella
from being lifted out by win
d.


Date:17‐Dec‐14www.potterybarn.com  Page1of1
Rev:  

Canopy For Umbrella
Parts Included:
(1) Umbrella Canopy
Care Instructions:
Brush to remove dirt and dust.
Canopy is removable; spot clean with water and mild soap; air dry.
Thankyouforyourpurchase
Stores|catalog
1. Place umbrella frame on flat
work area.Unscrew Finial
from top of umbrella
frame.Place Canopy over
umbrella frame. (Fig 1)
2. One hand holds rib, while one hand pulling pocket, to set each Rib
End into each pocket.(Fig 2-1/2-2)
NOTE: (For Rectangular canopies only)
Insert the Longest corner rib into pocket first then continue to insert
the ribs into all remaining pockets.
3. Secure Finial back to top by
turning clockwise. Assembly
is complete.(Fig 3)