Power Your Fun UFO1 User manual

INTERACTIVE LED STUNT DRONE
Ages 14+
USER MANUAL
OBSTACLE
AVOIDANCE
Altitude
Hold
360°
Flip
AUTO
LAUNCH
VARIABLE
SPEEDS
vibrant
leds
Visit us online at www.powerurfun.com for
product information and replacement parts.

2”
6.7” 6.7”
Product Dimensions:
UFO1 User Manual
WARNING
Please follow and retain this instruction manual for proper installation and use.
Some parts must be assembled by an adult.
Choking Hazard: Product contains small parts.
To avoid danger of suffocation, keep plastic packaging away from children and babies.
Periodically check the charger cords and wire plug for damages.
If you find damage, immediately stop using until repairs have been made.
The charger, baery pack, and the charging device must be inserted into a power
source that matches the voltage level specified on the product labeling.
Do not alter the configuration of the charger or use other than specified.
Do not use non-rechargeable baeries.
Adult surpervision is required when charging the rechargeable baery.
Do not mix old and new baeries or baeries of different types. Non-functioning
rechargeable baeries should be brought to a recycling center for proper disposal.
Keep baeries in a cool, dry place and away from fire.
Remove the baeries from the product when not in use for extended periods of time.
Do not touch the propellers when the drone is powered on.
Do not allow serious impact or dropping of drone or remote control to occur.
Clean the product with a so, clean cloth.
The manufacturer and the distributor take no responsibility for any damages caused
by improper operation of this product. Users are responsible for ensuring that the
product does not cause damage to itself, its user, or other people.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

Power On/Off
Sensor
Sensor
Sensor
Sensor
A1 Propeller
A1 Propeller
B1 Propeller
B1 Propeller
Droplet Remote
Controller
One Key Li / Land
3.7V Rechargeable
Lithium Baeries
USB
Charging
Cable
Drone introduction
Receiver
Sensor
Baery Cover
Directional Trim
Directional Controls
Forward/ Backward Trim
Roll/ Obstacle Avoidance
Power Buon
Rotational Trim
Throle / Rotational Controls
Emergency Stop
Speed Buon/ Headless Mode
1-Key Li/ Land
1. When the drone baery is low, the UFO1 will lower its altitude and land.
2. Do not operate the UFO1 if it is damaged or deformed.
3. Remove the baeries from the transmier when storing for extended periods of time.
4. If the UFO1 collides and falls to the ground, allow the drone to reorient itself on a horizontal
surface for 2-3 seconds before flying again.
Notice

1. Remove the baery cover with the
included screwdriver.
2. Install 4 AAA baeries with appropriate
polarity direction.
3. Reinstall the baery cover with the
included screwdriver.
A. The positive and negative electrodes of the baeries should match the corresponding polarity of the
baery compartment. Do not switch the polarity under any circumstances.
B. Do not mix old and new baeries or different types of baeries.
+
-
+
-+
-
+
-
Remote Transmier Baery Installation
ATTENTION
Lithium Baery Charging Instructions
Please remove the baery from
the drone before charging.
1. Remove the battery as indicated in Figure A and Figure B by opening the battery hatch,
unplugging, and then removing the battery from the compartment.
2. Connect the battery to the USB charging cable.
3. Connect the USB charging cable to your desired USB charging port. The charging light will turn on.
4. When the battery is fully charged, the light on the USB charging cable will turn off.
Figure A
Figure B
ATTENTION

2. Press the power switch on the remote controller until you hear the controller "beep” and
the lights on the drone stop flashing. Push the throle lever to its highest position and
then pull it back to its lowest postion. Your remote is now successfully paired to the drone.
3. If you have multiple drones, each will need to be paired seperately, one by one.
1. Aer the baery is properly connected, place the UFO1 on a flat horizontal surface and
long-press the drone’s power switch. The drone’s LED lights will flicker on and off.
1. Always operate the drone in a spacious environment free of obstacles.
2. Operate the drone indoors or in dry, low-wind environments.
B. Visit faa.gov to review current rules and regulations before flying the drone.
A. DO NOT operate the drone near the road or in harsh weather conditions.
C. This drone does not require registration as it weighs 2.5 ounces (below .55 lbs.).
D. This drone does not include a serial number.
E. Please ensure the flight area is approved by your local government.
F. Do not operate the drone within a radius of 5,500 yards from airports
or densely populated areas.
G. The maximum remote-control flight radius for this drone is 55 yards.
Accidents may occur if you aempt to operate the drone outside of the 55-yard radius.
H. Before flying, identify the front (Blue LEDs) and back (Green LEDs) ends of the drone
and maneuver at a distance of 3.5 yards behind the drone.
I. For optimal performance, please ensure the remote transmier is oriented behind the
back end of the drone.
TIP: The Blue LED lights indicate the front of the drone.
Pairing the Drone Before Operation
Drone Flight Environment
Lithium Baery Charging Precautions
For your safety, only use the USB charging cable provided.
Do not charge swollen, worn, or damaged baeries.
Never overcharge. Immediately disconnect the USB charger when the baery is fully charged.
IIf the baery is overcharged, it may overheat. Immediately stop charging if the plug has overheated or
you may cause damage to the baery.
Please supervise the charging process at all times; do not leave unaended.
Do not charge the baeries near flammable materials or on surfaces that can conduct electricity.
The charging temperature must be between 32°F and 100°F.
Please do not short-circuit the baeries.
ATTENTION

Push the directional
control stick upward to
perform a forward flip,
and backward to perform
a backward flip.
Push the directional
control stick le to
perform a le roll, and
right to perform a
right roll.
Press the roll buon;
the remote transmier
will “beep.”
Flip Forward
Flip Backward
Roll Right
Roll Left
Press the roll buon;
the remote transmier
will “beep.”
Basic Flight Control
Flips & Rolls
Ascending
Descending
Forward
Backward
Rotate Le
Rotate Right
Le Right
Push the throle stick
upward, the drone
will ascend.
Push the throle
stick backward, the
drone will descend.
Push the directional control
stick forward, the aircra
will go forward.
Push the directional control
stick backward,the aircra
will go backward.
Push the throle stick to
the le, the drone will
rotate le.
Push the throle stick to
the right, the drone will
rotate right.
Push the directional control
stick to the le, the drone
will fly to the le.
Push the directional control
stick to the right, the drone
will fly to the right.

Note: When the drone is 1 foot above the ground, it will become unstable due to the
influence of its own blade eddy current, which is called the “ground effect response.”
The lighter the drone, the greater the impact of the ground effect response.
Aer launching your drone, you may experience unintentional driing or rotating.
To fine-tune your drone’s flight stability, please follow the trim adjustment
procedures described below.
Hand Toss Induction Mode
Place the drone on a flat horizontal surface and hold the power buon
on the top of the drone until the lights flash on. While the drone lights
are flashing, you may pick the drone up and gently toss it up into the
air. The drone will enter into Induction Mode. When a hand or any
object approaches the boom sensor, the drone will automatically
rise and then slowly descend until it senses another object below it.
When a hand or object is sensed by the front or rear sensors, the
drone will react by moving in the opposite direction. Press the buon
on the droplet remote to land the drone. When the drone enters the
Hand Toss Induction Mode, the remote transmier can be used to
align the aircra. Please note that aer alignment is completed, the
drone will cease operating in Induction Mode and enter into
Remote Control Mode.
When the drone rotates to the
le, trim to the right until
corrected.
When the drone rotates to the
right, trim to the le until
corrected.
When the drone dris forward,
trim backward until corrected.
When the drone dris
backward, trim forward until
corrected.
When the drone dris to the
le, trim to the right until
corrected.
When the drone dris to the
right, trim to the le until
corrected.
If the altitude of the drone is abnormal, the drone may be reset: While the drone
is siing on a flat horizontal surface, simultaneously press and hold both the
throle and directional control sticks down and to the le. The drone’s LEDs will
flash and then become solid again. Release the sticks. Your drone is now reset.
Rotates Right
Rotates Le
Dris
Forward
Dris
Backwards
Dris
Le
Dris
Right
Flight Trim Controls
Other Drone Functions

Infrared Induction Mode
When you are in Induction Mode, you may enter into Remote
Control Mode by powering the remote transmier ON and then
pressing the throle stick up and then down. You will then have
full control of the drone.
To enter back into Induction Mode, turn the remote transmier
OFF, then press the buon on the droplet remote. You will then be
in Induction Mode.
Headless Mode
While flying the drone, position yourself behind the drone
and long-press the top le buon. The remote will beep
steadily and the drone will automatically orient its flight
movements forward/backward from your position.
Emergency Stop
If you ever need to abruptly land the drone, long-press
the emergency stop buon to land the drone quickly.
1-Key Li / Land
While the drone is on a flat horizontal plane and successfully
paired, press the 1-Key Li buon to launch it in the air. While
flying, you may press the same buon again to land the drone.
Droplet Remote Mode
While the drone is on a flat horizontal plane and powered ON,
the droplet remote buon will launch it in the air and enter into
Induction Mode. While flying, you may press the same buon
again to land the drone.