Powermat PM-500-SSTT User manual

ORIGINAL INSTRUCTIONS
USER MANUAL
BELT SANDER, tray
PM-500-SSTT

2
Table of Contents
SYMBOLS WARNING / INFORMATION .............................................. ........................................... 3
DESCRIPTION OF THE DEVICE ................................................ .................................................. ................................. 3
TECHNICAL DATA ................................................ .................................................. ................................ 4
PURPOSE OF THE DEVICE ................................................ .................................................. ............... 4
SAFETY RULES ................................................ .................................................. .................... 5
Workplace ................................................ .................................................. .................................................. .. 5
Safety in use ................................................ .................................................. ........................... 5
Safety related to the use and maintenance ............................................ ............................................... 5
General thoughts ................................................ .................................................. .................................................. 6 ..
Basic steps before you begin working ............................................. ............................................... 6
Actions during and after its completion ........................................... .................................................. ....... 6
It is forbidden to: ............................................... .................................................. .................................................. ..... 7
ASSEMBLY ................................................. .................................................. ............................................... 7
The installation disk grinding ............................................... .................................................. .............................. 7
Installing the top disk grinding .............................................. .................................................. ...................... 9
Installation stopper arm sanding ............................................. .................................................. ........... 9
OPERATION AND ADJUSTMENT DEVICE .............................................. .................................................. .... 10
Terms of use ................................................ .................................................. ..................................... 10
Adjusting the sanding belt centering .............................................. .................................................. .......... 10
Changing the position of the arm grinding .............................................. .................................................. ............... 11
Setting the angle stopper .............................................. .................................................. .................... 11
Tilting top grinding wheel .............................................. .................................................. .................... 11
The setting angle tabletop grinding wheel ............................................ ................................................. 12
Sanding belt replacement ............................................... .................................................. ............................. 12
Replacing the grinding wheel ............................................... .................................................. ............................. 12
MAINTENANCE ................................................. .................................................. ................................... 12
TROUBLESHOOTING ................................................ .................................................. ......... 13
REMOVAL OF USED ............................................... .................................................. ....... 14
COMPANY INFORMATION ................................................ .................................................. ............................ 14
DECLARATION OF CONFORMITY ................................................ .................................................. .................... 14
CONSTRUCTION SCHEME ................................................ .................................................. ............................. 15

3
SYMBOLS WARNING / INFORMATION SYMBOLS WARNING / INFORMATION
You should wear hearing protection.
Be used respiratory protection.
You should use eye protection.
DESCRIPTION OF THE DEVICE
1. Device
2. Working table.
3. Blade guard.

4
4. Stopwatch.
5. Lower blade guard ejection of waste.
6. Rubber feet.
7. Angle.
8. Shield.
9. 4mm hex wrench.
TECHNICAL DATA
motor power supply ~ 230V / 50Hz
Engine output no-load S 2 - 30 minutes Engine output no-load S 2 - 30 minutes Engine output no-load S 2 - 30 minutes 500W
belt speed 1450 rpm
size tape 100mm x 914mm
size shield 150mm
Working table 190mm x 125mm
Worktop shield 178mm x 126mm
tilt top 0 ° - 45 °
Gross weight 12g
Net weight 11kg
Sound power level L WASound power level L WA 92dB (A)
PURPOSE OF THE DEVICE
The device is intended for grinding at an angle of the materials for home use. Any other use, which clearly does not
allow this user manual, can lead to equipment damage and pose a serious threat to the user.
It is forbidden to use the machine in the rain or in a humid environment. The manufacturer is not liable for damages
that have arisen as a result of misuse or improper handling.

5
Because of safety reasons the device can not be used by children and young people under the age of 18
and by persons under the influence of alcohol, drugs or other intoxicants.
Persons who are not familiar with this manual, please read carefully before its first use.
SAFETY RULES
Workplace
• KEEP WORK AREA CLEAN. Mess in the workplace increases the likelihood of accidents.
• Pay attention to workplace conditions. Do not use tools in damp, wet. Do not expose to rain. Never use
electrical tools near flammable gases and liquids.
• KEEP CHILDREN AWAY FROM UNIT. Children should not be in the workplace. Each dispersal may cause
an accident. Do not allow children to carry the device or any accessories related to it.
Safety in use
• When working with tool use caution and common sense. Do not operate tool while under the influence of
alcohol, drugs and prescription drugs. Read leaflet drugs that you are taking, to see if they affect your
judgment and reflexes. If you have any doubt, do not operate the tool.
• Use appropriate protective accessories. When working with the tool, wear safety goggles, dust mask,
non-slip boots, helmet and ear protection whenever the situation demands. This will reduce the risk of
accidents.
• Avoid accidental start up the tool. Before plugging in, make sure the switch is in the OFF position. When
carrying the tools do not hold it by the switch, since this increases the risk of accidents.
• Remove any adjusting keys before running the tool. A key attached to the rotatable part of the tool can
cause injuries.
• Do not reach over the device. During operation, maintain a stable position and balance. This allows for
better control of the device in the event of unforeseen circumstances.
• Dressing up PROPERLY. Do not wear loose clothing or jewelry as they can be screwed into the moving
parts. It is recommended to work with the tool wear shoes with non-slip soles. Long hair should be
protected. Always wear suitable protective clothing.
• Use mounting workpiece. It is safer than using a hand support, as it allows you to use both hands to operate
the device.
Safety related to the use and maintenance
• Do not overload the tool. The device will work better and safer at loads for which it was designed. Do not try
to use incompatible accessories to increase productivity tools.

6
• Do not use a tool that has a damaged switch. A tool that can not be controlled with the switch creates a
danger and should be repaired.
• Before adjusting, repairing, changing accessories or storage, disconnect from the power tool. Such
precautions will reduce the risk of accidental starting.
• Keep the tool unplugged and out of reach of children and people
unauthorized.
• You should regularly carry out maintenance tool. Be sure to check that there is no backlash and faults
moving parts, they are not damaged parts or tools if there were no other defects that could disrupt the
proper operation of the device. In the event of irregularities should immediately repair the tool. Multiple
vulnerabilities has its source in improper maintenance.
•Use tools and accessories related to it in accordance with these instructions and in the correct manner. It should
take into account the conditions and the type of work performed.
• Using a tool misused can cause serious accidents.
• Faulty switch should be replaced by an authorized service. Do not use tools with defective On / Off switch.
• Do not leave tools unattended when it is turned on. Before leaving the workplace, always switch off and wait
for it to completely stop.
•If the main cable is damaged it must be replaced with the appropriate cable adapter.
• The cable can be obtained from the distributor device. The cable can be replaced by a service agent or a
qualified electrician.
General thoughts
• Electrical equipment should meet the requirements of health and safety of Polish Standards and the relevant
provisions for the lifetime.
• People employed in electrical devices should be equipped with suitable work clothing and personal
protective equipment.
• People employed in electrical equipment should comply with all health and safety regulations governing the
electrical equipment.
Basic steps before you begin working
• Before starting work, read the documentation of electrical equipment and to prepare the necessary tools,
equipment, warning signs and necessary equipment insulation.
• Check the condition of facilities and electrical installations (the insulation of wires, cables, plugs, switches,
sockets), zero, earth, fire and security status przeciwporażeniowych.
• Check the condition of the current security.
• Check the condition of fire marking equipment and electrical installations.
Actions during and after its completion
•Electric tools must be operated only in accordance with its intended purpose.
• If you need to leave the workplace should be supported to stop the machine and all other equipment that
may cause a hazard and disconnect the power.

7
• If necessary, work under pressure, use tools and equipment insulation and dielectric gloves and shoes.
• If the automatic switch-off or burn fuses, switch it on again when the cause of the short circuit and setting up
a new fuse.
• For connecting machines and equipment to be used grounded outlet, if required by the electrical installation.
• After the work, protect electrical equipment, organize the workplace, tools and equipment.
It is forbidden to:
• Acceptance of electrical equipment without confirmation of the effectiveness of protection against the
possibility of electric shock.
• Making changes to the supported device.
• Removal of protection, security, closing relays, blocking switches, fuses the use of temporary repairs, use
the wrong fuse.
• Fuse setting the machine turned on.
• Pull the cord when removing the electric plug from the socket.
• Maintenance of plug-in sockets, and plug-ins or the casing is damaged insulation insert.
•Overloading of electrical equipment above the permissible value.
• Touching live parts, terminal capacitors (even when they are disconnected).
•Leaving unattended electrical equipment connected to the network. All electrical equipment must be
disconnected from the mains before leaving the workplace.
• Access to devices or electrical unauthorized, minors, including children, sick people, under the influence of
alcohol or other drugs.
ASSEMBLY
Installing the grinding disc
1. Using a screwdriver, unscrew the 3 screws at the top of roll. 1. Using a screwdriver, unscrew the 3 screws at the top of roll.

8
2. Tighten cover drive to the device. 2. Tighten cover drive to the device.
3. Install the cover disc ejection by 4mm Allen key. 3. Install the cover disc ejection by 4mm Allen key.
4. Unscrew the four screws from the bottom cover. 4. Unscrew the four screws from the bottom cover.
5. Position the holes in the shells and tighten the four screws. 5. Position the holes in the shells and tighten the four screws.

9
Installing countertop grinding disk
1. Position the support table with a hole in the device and then place the support in 1. Position the support table with a hole in the device and then place the support in
hole.
2. To avoid injury to fingers countertop should be a few millimeters from the blade. tighten2. To avoid injury to fingers countertop should be a few millimeters from the blade. tighten
counter.
Installation stopwatch sanding arm
1. Unscrew a screw. 1. Unscrew a screw.

10
2. Install a timer, tighten the screw. 2. Install a timer, tighten the screw.
3. Tighten the cover to the stopwatch. 3. Tighten the cover to the stopwatch.
OPERATION AND CONTROL DEVICE
Terms of use
Humidity - max. 70%
Temperature - 5 ° C to + 40 ° C
The device can not be used in places with an increased risk of fire or explosion.
Adjusting the sanding belt alignment
1. Turn off the device. 1. Turn off the device.
2. Adjusted by means of control knob. 2. Adjusted by means of control knob.
3. Check whether the machine running the tape is centered. 3. Check whether the machine running the tape is centered.

11
Changing the position of the grinding arm
1. Turn off the device. 1. Turn off the device.
2. Loosen the nut, the arm in the desired position, tighten the nut. 2. Loosen the nut, the arm in the desired position, tighten the nut.
Setting the angle stopper
1. Up to adjust tension on the belt stretched. 1. Up to adjust tension on the belt stretched.
2. Use angle. 2. Use angle.
3. Loosen the nut, set the timer, tighten the nut. 3. Loosen the nut, set the timer, tighten the nut.
Tilting top grinding wheel
You can tilt the table top up to 45 degrees. Loosen the
knob, tilt top table top and tighten the knob.
Remember to tilt the table top he kept the distance of a
few millimeters from the grinding wheel.

12
The setting angle tabletop grinding wheel
Use the angle to this process by applying it from one side to the disc, and on the other to the top.
Sanding belt replacement
1. Loosen the nut stopwatch. 1. Loosen the nut stopwatch.
2. Up to loosen the tension of the belt. Remove the tape.2. Up to loosen the tension of the belt. Remove the tape.
3. Install the new tape. 3. Install the new tape.
4. Tighten the stopwatch. 4. Tighten the stopwatch.
5. Up to stretch the tape tension. Check the operation of the tape.5. Up to stretch the tape tension. Check the operation of the tape.
6. If necessary, center the tape. 6. If necessary, center the tape.
Replacing the grinding wheel
1. Remove the top. 1. Remove the top.
2. Remove the lower cover. 2. Remove the lower cover.
3. Unhook the old shield. Clean the disc.3. Unhook the old shield. Clean the disc.
4. Attach the new tape. 4. Attach the new tape.
5. Replace the bottom cover and top. 5. Replace the bottom cover and top.
MAINTENANCE
• The device does not require sophisticated maintenance. In the event of the occurrence of defects or
malfunction, repairs should be made by a qualified service technician.
• Initially and after every 100 hours of operation lubricate all parts of the links (if necessary before application
to remove all swarf and dust with a brush).
• Check regularly stickers with safety information. If necessary, replace the stickers.
•Regularly check the condition of the tape and the tape guide.
• In good order and correctly adjusted guide rollers ensure free movement of the tape and accurate grinding.
• Keep it in a closed, dry area.
•After each finished work to remove chips, swarf and dust.

13
NCES PRO BLEMÓW NCES PRO BLEMÓW
Problem Possible cause Solution
The device turns off or does not
start
• ON / OFF switch is
damaged
• Device
unplugged
• The device is
overloaded
• Broken circuit breaker
or fuse
• A damaged power
cable
• Check switch
• Check all power
connections
• Let the unit cool down
and reset them disabling
switch
• Replace the fuse or
reset the circuit breaker
•Replace the power
cord
The machine slows down during
operation
• Too much contact force
component for
abrasives
•Decrease contact
pressure element for
abrasive material
Unsatisfactory work results
• Poor (too small / too
big) grain size of
abrasives
• Use materials with grain
size
Too rapid wear
• Too small a
particle size
of abrasives
•Apply the material with a
larger particle size
Inadequate Angle
grinding
•The angle is
misaligned •Adjust the angle
Shield does not rotate in the
center position
• The grinding wheel is
mounted improperly •Attach the shield to the
center position
Grinding rolls off the bearings • The sanding belt is
poorly mounted
•Replace the grinding belt
in the central position
Workpiece becomes very hot
• Abrasives dirty varnish
• Too much force
• Change abrasive
• Shrink force

14
REMOVAL OF USED
End of life do not dispose of this product by normal household waste, but take it to a
collection point and recycling of electrical and electronic equipment. This is indicated by the
symbol on the product,
user manual or packaging. Thanks
re-use, material utilization or other forms of old appliances, you make an important
contribution to protecting our environment.
COMPANY DETAILS
PH Powermat TMK Bijak Sp. General Partnership Ul.
Defenders of the Gdansk Post 97 42-400 Zawiercie
DECLARATION OF CONFORMITY

15
SCHEME OF CONSTRUCTION