Powr-Flite PDF5 User manual

POWR-FLITE LIMITED WARRANTY
Powr-Flite will repair or exchange parts for your dryer in the event of a manufac-
turing defect as follows:
PARTS: New or comparable rebuilt parts, for one year after original purchase.
LABOR: Carry-in service can be obtained during the warranty period by taking
your dryer to an Authorized Powr-Flite Warranty Service Center.
IMPORTANT WARRANTY CONDITIONS: Apurchase receipt or other proof of
date of original consumer purchase also will be required before warranty service
is rendered.
This warranty covers normal use and does not cover damage which occurs in
shipment or failure resulting from alteration, accident, misuse, abuse, neglect, or
improper maintenance.
STATEMENT: This warranty is not transferable and extends only to the original
purchaser when a new Powr-Flite dryer is purchased from an Authorized Powr-
Fite Dealer.This warranty gives you specific legal rights, and you may have
other rights that vary from state to state.
A Tacony Company, Fort Worth, Texas 76140-1710, Call Toll-Free [phone]
Operator’s Manual
©Powr-Flite, All Rights Reserved X9191 08.05
Commercial
Axial Fan
Standard F5 Models
PDF5, PDF5DX
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

This appliance must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current to reduce the risk of electric
shock. This appliance is equipped with a cord having an equipment-grounding con-
ductor and grounding plug. The plug must be plugged into an appropriate outlet that
is properly installed and grounded in accordance with all local codes and ordi-
nances.
This appliance is for use on a nominal 120 volt circuit and has a ground plug (see
illustration, right). Make sure that the appliance is connected to an outlet having the
same configuration as the plug. No adaptor should be used with this appliance.
WARNING -Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or service person if you
are in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the appliance – if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
GROUNDING INSTRUCTIONS
Prong or
Grounding pin
Grounded
Outlet
Grounded
Outlet Box
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
When using an electrical appliance, basic pre-
cautions should always be followed.
WARNING- To reduce the risk of fire, electric
shock or injury:
Use only as described in this manual. Use
only manufacturer’s recommended compo-
nents and attachments.
Use only indoors. Do not use outdoors or
expose to rain.
Do not use with damaged cord or plug. If
appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, return it to your Authorized
Powr-Flite dealer.
Do no pull or carry by cord, use cord as a
handle, close door on cord, or pull cord
around sharp edges or corners. Keep cord
away from heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Donot handle plug or appliance with wet
hands.
Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, hair and anything that may reduce air
flow.
Turn off all controls before unplugging.
Do not attempt to service the unit while appli-
ance is plugged in.
Appliance may cause a fire when operating
near flammable vapors or materials. Do not
operate this machine near flammable fluids,
dust or vapors.
Connect to a properly grounded outlet.
Do not use with any solid state speed control
device.
This unit is thermally protected.
FOR BEST PERFORMANCE
•Keep machine clean and in good operating condition.
•Have machine checked periodically by your Authorized
Powr-Flite Dealer.
•Use only authorized service centers for parts or service.
•Store machine carefully in dry area.
•For optimum drying performance and safety, study and
follow your operators manual.
SAVE THESE INSTRUCTIONS
WARNING
Do not stack dryers more than
4(four) units high for transport,
5(five) units high for storage.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

OPERATING INSTRUCTIONS
MAINTENANCE/TROUBLE SHOOTING
1.Plug in to a standard outlet with the correct voltage and amperage for the unit.
2. Place the dryer in the desired operating position.
3. Set the switch at the desired speed: low or high.
4. Check for proper operation before leaving the unit unattended.
Donot move or carry the dryer when it is running.
Daisy-chained: Up to 6 units may be plugged into on a single 15 amp circuit and
up to 9 on a 20 amp circuit. The F5 is equipped with dual power outlets that will
allow you to “daisy chain” up to 5 units units. Do not “daisy chain” more than 5 units.
The F5 power system has a 12 amp circuit breaker built in that will trip if more than 5
units are “daisy chained” from a single machine.
12 AMP Resettable Circuit Breaker
The F5 Powr-Dryer features a 12 amp circuit breaker that will “trip” if more than 12
amps of electrical current is drawn through the cord.
GFCI Protection and Outlet
The F5 Powr-Dryer provides a standard duplex GFCI outlet for daisy-chaining multi-
ple units together. The GFCI protection promotes operator safety and will “trip” is an
electrical ground fault is sensed. To test the GFCI protection, press the TEST button.
If operating properly, the RESET button on the GFCI outlet will pop out.
Operating Positions
The F5 Powr-Dryer is designed to operate in multiple positions for any type of dry-
ing.
1. Tilt Back –Tilt the F5 backward on the four curved molded legs at an angle
to direct air for elevated drying.
2. Upright –Set the F5 square with the handle on the top to direct air across
aroom.
3. Tilt Forward –Tilt the F5 forward on the “standing legs at an angle to direct
airflow along the flow in front of the dryer.
4. Face Down –Set the F5 on the four curved molded legs with the “standing
legs” facing up to direct air straight down.
5. Powr Pitch –Model PDF5 is equipped with a 3º down angle leg.
6. Stack for Storage –the F5 Powr-Dryer interlock and stack for easy
storage and transport.
Periodic Maintenance
1. Check power cord for any breaks, seperations or cuts.
2. Make sure the ground pin or grounding prong is intact or
the machine will be unsafe to operate.
Trouble Shooting (if the dryer will not run)
1. Check electrical cord; is it firmly seated in wall outlet
2. Check GFCI and reset if tripped
3. Check if dryer circuit breaker is tripped, reset if necessary.
4. Check to see if building circuit breaker is tripped. If circuit
is overloaded, move cord to different GFCI outlet.
5. If using an extension cord, make sure it is in good
condition, proper gauge and firmly connected.
2postion switch and daisy-chained outlets
Cord wrap
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ASSEMBLY
ref# part # description
01 X9180 Housing, Axial Fan
02 PD3C Foot, Black Rubber, Short
03 X9098 Screw, #10 x 1”, A point, Pan Head
04 X8260 Nut, 8-32 Lock, w/ Nylon Inserts
05 72719A Bracket, Axial Fan Motor
06 X9183 Grill Axial Fan
07 X9189 Label, Round (at grill)
08 X9195 Caster Receiver
09 P50 Wheel and Socket
10 72020A Screw,Self-Tap, PHMS, Zinc, #12 x 1”
11 X9181 Motor, 115 VAC, .25 HP, 4-Pole
12 X8209 Screw, 1/4-20 x 1/2", Self Locking Flange
13 X9065 Screw, Hex Socket Cap, 1/4-20 x 1"
14 X8990N Handle / Wheel Assembly, Narrow
ref# part # description
15 X8848 Jacknut, 1/4-20, Steel, #8LJN
16 X9190 Label, Product
17 72721A Switch Panel
18 X9048 Rocker Switch
19 X918 Circuit Breaker, 12A
20 X9188 Screw, 6-32 x 3/8”, Black MS
21 X8926 20’ HD, 3-wire cord, 16/3 SJTW, 115 volts
22 PD8 Strain Relief, 1/2" NPT
23 X8008N Nut, Lock, 1/2" Steel Conduit
24 X9187 GFCI outlet, Female Plug
25 X9182 Fan Blade Assembly
26 F631 Round Belt
27 72470A Heat Shrink, Blk, 1/2” x 200’,
28 PD3B Foot, Black Rubber, Tall
Use PD3C for units with handle / wheel assembly (PDF5DX)
Parts for PDF5, PDF5C, PDF5DX
©Powr-Flite, All Rights ReservedX9191 08.05
PDF5C caster kit
For model PDF5DX only
https://harrissupplyind.com-ToOrderPartsCall608-268-8080