PRAXIS WETBENCH User manual

INSTRUCTION MANUAL
FOR THE ORIGINAL
WETBENCH

CONTENTS
INCLUDED MOUNTING HARDWARE ............................... 3
WETBENCH HARDWARE......................................................4
ACRYLIC LEG INSTALL .......................................................... 5
LEG TO MIDTRAY INSTALL ..................................................6
HARD DRIVE TO MIDTRAY INSTALL................................ 7
PSU INSTALL .............................................................................. 8
OPTICAL DRIVE INSTALL..................................................... 9
INSTALL OF MIDTRAY BRACKETS.................................. 10
ACRYLIC MOTHERBOARD INSTALL ................................11
MOTHERBOARD STANDOFF INSTALL...........................12
GPU BRACKET INSTALL.......................................................13
MOTHERBOARD TRAY INSTALL...................................... 14
MOTHERBOARD INSTALL ...................................................15
RADIATOR TRAY INSTALL ..................................................16
RADIATOR INSTALL...............................................................17
VANDAL SWITCH INSTALL .................................................18
WETBENCH COMPATIBILITY .....................................BACK

3
MOUNTING HARDWARE
PART # PART NAME QTY
1 M3 MOTHERBOARD NUT 24
2 M4X6 LOWHEAD SCREW 20
3 12MM MOTHERBOARD STANDOFF 14
4 M3 SPLIT WASHER 11
5 M3X10MM SOCKET CAP 11
6 M3x8MM GPU SCREWS 10
7 6/32 .25” HDD NYLON SCREW 14
8 M4X8MM MIDTRAY NYLON SCREW 10
9 M3x5MM SSD/DRIVE NYLON SCREW 14
10 M3 MOTHERBOARD SCREW 14
11 2.5MM HEX KEY WRENCH 1
2 43 10 1161 7 8 95

1
4
7 8 9
2
5
3
6
WETBENCH HARDWARE
ITEM # PART NAME QTY
1 MOTHERBOARD TRAY 1
2 MID TRAY 1
3 LEFT & RIGHT SLANTED LEGS 1
4 BACK RADIATOR TRAY 1
5 GPU BRACKET 1
6 FRONT AND BACK PSU BRACKET 1
7 5.25” BAY BRACKET 2
8 ACRYLIC INSERTS FOR LEGS 2
9 ACRYLIC INSERTS FOR MOTHERBOARD 1

5
M3 NUT
STEP 1 | INSTALLING ACRYLIC TO LEGS
Grab your leg and acrylic insert. Be sure to pull o the brown
protective paper from your acrylic. Attach your leg and acrylic
using 1 M3X10MM SOCKET CAP (part 5), 1 M3 SPLIT WASHER
(part 4), and 1 M3 MOTHERBOARD NUT (part 1).
M3 CAP
M3 WASHER

STEP 2 | ATTACHING LEGS TO MIDTRAY
M4x6MM
FIGURE 1
Gather the Midtray and both legs. Attach them using 4 M4X6
lowhead screws (part 2) on each side. Be sure that the midtray
overlaps the leg and that you lean your leg at an angle and
then straighten it into the midtray as Figure 1 shows.

7
STEP 3 | HARDDRIVE INSTALL
Install any HDD or SDD on top of the mid tray. These drives can
be oriented on either front or back depending on your prefer-
ence. SSD’s use M3x5 nylon screws (part 9) and HDD’s utilize
6/32” .25 nylon screws (part 7).
6/32”
M3x5MM

STEP 4 | PSU INSTALL
After your drives are installed you can screw in the back of
your PSU to the bracket. Then connect it to the location of the
midboard tray of your choosing. (Figure 2.2).
REAR VIEW
FIGURE 2
M4X8MM

9
STEP 5 | OPTICAL DRIVE INSTALL
Use M3x5 nylon screws (part 8) to install your optical drive. If
you’re not using one you can disregard this step.
M3x5MM

STEP 6 | MIDTRAY BRACKETS INSTALL
M4X8MM
After your drives and/or ODD is installed you can install your
brackets onto the midtray using M4x8 nylon screws (part 8).
Note: These brackets are modular and can be oriented on both
the left and right side and slid forward and backwards.