PRAXIS PE-7142IP User manual

If the product is to be put out of operation definitively, take it to
a local recycling plant for a disposal which is not harmful to the
environment.
PE-7142IP 2.8-12
OUTDOOR NETWORK IR DOME CAMERA
PACKING LIST
Name Q-ty
PE-7142IP 2.8-12 - OUTDOOR NETWORK
IR DOME CAMERA 1
CD disk:
1. Praxis IPC CMS
2. User Manuals for IP series Praxis
3. Video instructions
4. Helpful information
1
User Manual 1
SPECIFICATION
Image Sensor
Resolution
Min. Illumination
S/N
Lens
IR Status
Day/Night
Network
Delay
Frame Rate
1/3” SONY 2 Mpix CMOS HiSilicon
1920 X 1080
0.05 Lux
More 50db
2.8-12 mm / F 2.0
24PCS IR RANGE: 25 m
IR cut filter with auto switch, IR sensor.
1 RJ45 Ethernet 10/100 M
LAN 0.3S
2 Mpix / 25 FPS
Video Compression H.264 / JPEG
Protocol RTSP/FTP/PPPOE/DDNS/NTP
UPnP/TCP/SMTP
ONVIF ONVIF 2.4
User Permission Multi-user Classification Managment
Housing Metal outdoor IP66
Power 12 V DC / PoE
Current
Consumption 1А max
Dimension -
Weinght 800 g
Temperature -30 о С ~ +55 о С
SAFETY INSTRUCTION
Thank you for purchasing this Outdoor Network IR Camera
PRAXIS.
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Do not cut or peel off the cable.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electric-
ity limit.
10. Installation should be done by qualified service person only.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
Magnitude to constitute a risk of electric shock to persons.
The symbol is intended to alert the user to the presence of important operat-
ing and maintenance (servicing) Instructions in the literature accompanying
the appliance.
FEATURES
1. Support Single Stream, Dual Stream, TriStream
2. Support WEB Configuration, IE Surveillance
3. Support Android, IOS remote monitoring
4. Support Motion Detection Recording/ Capture upload via FTP/SMTP
5. Support DDNS
6. Support OSD,allowns to modify system time and IP Camera’s name
7. Support P2P
ACTIVATION
1.Open your IE browser.
2.Enter the IP addressdress:192.168.1.168.
Введите его в адресной строке вашего браузера.
3.Log on for the first time need to download and install the OCX
controls. When the installation is complete you will pop up the fol-
lowing tips.
4.Click OK, and then refresh the interface, Enter your account num-
ber and password, our default accounts: admin password: admin.
How to pass the “RTSP” access the IP camera
Download and install the VLC software.
Open the media, select open network stream.
VLC madia player 4 Media 4 Open Network Stream...
Input rtsp://192.168.1.168:80/0
Click Play, and then a password window will pop up.
Default username: admin
Default password: admin
Click OK.
Default IP of the IP camera is 192.168.1.168. If your computer is not in
the 192.168.1.xxx, you must be unified network segments, for example,
modifying the computer address or modify the IP camera.
PRAXIS IPС CMS FEATURES
1.Support the N organizational structure, management and user
access management.
2.To support the search device.
3.Support for displaying the front-end equipment list.
4.Support for multiple video window on the screen and the screen
control.
5.Support privacy covered.
6.Support capture.
7.Support motion dectect.
8.To support the client logs.
9.Support all kinds of small medium and large databases, such as
SOL, MYSQL and XML data.
10.Add and edit device support EXCEL software.
11.Support intelligent video transmission protocol.
12.Coordinated operation of multiple server support.
13.To support real-time monitoring and alarm video support, auto-
matic monitoring video recording, video playback
14.The support network and load balancing.
15.Support network upgrading.
16.DIY user interface and multi language support.
17.Support upload with SMTP and FTP.
18.Support plan videos record.
19.Support multi connected devices, video equipment.
20.Support for XML data storage.
TROUBLESHOOTING GUIDE
Restore the factory settings situation
1. Web port is changed and device can’t access Camera.
2. IP address is changed so that it can’t access Camera.
3. Other unknown reason so that it can’t access Camera.
Why does it shows “Get Param Failed”?
1.Please check the IP information, such as port.
2.Please make sure the IP Camera connected correctly.
3.The network status is poor.
Why screen get stuck, when we preview remote?
1.Network unstable (We need a better network).
2.Computer configuration is poor, For example, CPU or Graphics
card.
3.Simultaneous access to too many people.
4.Your camera frame rate and resolution of the problem.
Adding client equipment what are the issues that need atten-
tion?
In our client add device, manually entering the information must be
correct. If the camera working in LAN, you can search and add, but
you must pay attention to your user ID and password.
Why use Web pages can’t access IP camera?
1.The IPC input address errors.
2.Do not has install the corresponding OCX control.
3.The IPC logon account password error.
4. Relatively slow speed of the network or online more.
Why can not access the camera after update?
Clean browser cache. Steps: open IE, click “Tools” and select “Inter-
net Options”, then you can see “Temporary Internet files” and click
“Delete Files”, it will prompt a dialog you need to check “Delete all
offline content” and click “OK”. Also you can click “Start” and select
“Run” then enter “cmd”, enter “arp - d” in “Command Prompt”
interface. Re-access the camera.
Which one is the camera’s onvif port?
Our onvif ports: 80 or 8999.
CONNECTING
RJ45 Ethernet interface (VIDEO) (РоЕ)
12 V DC/1A
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE
PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN SPECIFIED POWER
SOURCE.

If the product is to be put out of operation definitively, take it to
a local recycling plant for a disposal which is not harmful to the
environment.
PE-7142IP 2.8-12
OUTDOOR NETWORK IR DOME CAMERA
PACKING LIST
Name Q-ty
PE-7142IP 2.8-12 - OUTDOOR NETWORK
IR DOME CAMERA 1
CD disk:
1. Praxis IPC CMS
2. User Manuals for IP series Praxis
3. Video instructions
4. Helpful information
1
User Manual 1
SPECIFICATION
Image Sensor
Resolution
Min. Illumination
S/N
Lens
IR Status
Day/Night
Network
Delay
Frame Rate
1/3” SONY 2 Mpix CMOS HiSilicon
1920 X 1080
0.05 Lux
More 50db
2.8-12 mm / F 2.0
24PCS IR RANGE: 25 m
IR cut filter with auto switch, IR sensor.
1 RJ45 Ethernet 10/100 M
LAN 0.3S
2 Mpix / 25 FPS
Video Compression H.264 / JPEG
Protocol RTSP/FTP/PPPOE/DDNS/NTP
UPnP/TCP/SMTP
ONVIF ONVIF 2.4
User Permission Multi-user Classification Managment
Housing Metal outdoor IP66
Power 12 V DC / PoE
Current
Consumption 1А max
Dimension -
Weinght 800 g
Temperature -30 о С ~ +55 о С
SAFETY INSTRUCTION
Thank you for purchasing this Outdoor Network IR Camera
PRAXIS.
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Do not cut or peel off the cable.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electric-
ity limit.
10. Installation should be done by qualified service person only.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
Magnitude to constitute a risk of electric shock to persons.
The symbol is intended to alert the user to the presence of important operat-
ing and maintenance (servicing) Instructions in the literature accompanying
the appliance.
FEATURES
1. Support Single Stream, Dual Stream, TriStream
2. Support WEB Configuration, IE Surveillance
3. Support Android, IOS remote monitoring
4. Support Motion Detection Recording/ Capture upload via FTP/SMTP
5. Support DDNS
6. Support OSD,allowns to modify system time and IP Camera’s name
7. Support P2P
ACTIVATION
1.Open your IE browser.
2.Enter the IP addressdress:192.168.1.168.
Введите его в адресной строке вашего браузера.
3.Log on for the first time need to download and install the OCX
controls. When the installation is complete you will pop up the fol-
lowing tips.
4.Click OK, and then refresh the interface, Enter your account num-
ber and password, our default accounts: admin password: admin.
How to pass the “RTSP” access the IP camera
Download and install the VLC software.
Open the media, select open network stream.
VLC madia player 4 Media 4 Open Network Stream...
Input rtsp://192.168.1.168:80/0
Click Play, and then a password window will pop up.
Default username: admin
Default password: admin
Click OK.
Default IP of the IP camera is 192.168.1.168. If your computer is not in
the 192.168.1.xxx, you must be unified network segments, for example,
modifying the computer address or modify the IP camera.
PRAXIS IPС CMS FEATURES
1.Support the N organizational structure, management and user
access management.
2.To support the search device.
3.Support for displaying the front-end equipment list.
4.Support for multiple video window on the screen and the screen
control.
5.Support privacy covered.
6.Support capture.
7.Support motion dectect.
8.To support the client logs.
9.Support all kinds of small medium and large databases, such as
SOL, MYSQL and XML data.
10.Add and edit device support EXCEL software.
11.Support intelligent video transmission protocol.
12.Coordinated operation of multiple server support.
13.To support real-time monitoring and alarm video support, auto-
matic monitoring video recording, video playback
14.The support network and load balancing.
15.Support network upgrading.
16.DIY user interface and multi language support.
17.Support upload with SMTP and FTP.
18.Support plan videos record.
19.Support multi connected devices, video equipment.
20.Support for XML data storage.
TROUBLESHOOTING GUIDE
Restore the factory settings situation
1. Web port is changed and device can’t access Camera.
2. IP address is changed so that it can’t access Camera.
3. Other unknown reason so that it can’t access Camera.
Why does it shows “Get Param Failed”?
1.Please check the IP information, such as port.
2.Please make sure the IP Camera connected correctly.
3.The network status is poor.
Why screen get stuck, when we preview remote?
1.Network unstable (We need a better network).
2.Computer configuration is poor, For example, CPU or Graphics
card.
3.Simultaneous access to too many people.
4.Your camera frame rate and resolution of the problem.
Adding client equipment what are the issues that need atten-
tion?
In our client add device, manually entering the information must be
correct. If the camera working in LAN, you can search and add, but
you must pay attention to your user ID and password.
Why use Web pages can’t access IP camera?
1.The IPC input address errors.
2.Do not has install the corresponding OCX control.
3.The IPC logon account password error.
4. Relatively slow speed of the network or online more.
Why can not access the camera after update?
Clean browser cache. Steps: open IE, click “Tools” and select “Inter-
net Options”, then you can see “Temporary Internet files” and click
“Delete Files”, it will prompt a dialog you need to check “Delete all
offline content” and click “OK”. Also you can click “Start” and select
“Run” then enter “cmd”, enter “arp - d” in “Command Prompt”
interface. Re-access the camera.
Which one is the camera’s onvif port?
Our onvif ports: 80 or 8999.
CONNECTING
RJ45 Ethernet interface (VIDEO) (РоЕ)
12 V DC/1A
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE
PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN SPECIFIED POWER
SOURCE.

If the product is to be put out of operation definitively, take it to
a local recycling plant for a disposal which is not harmful to the
environment.
PE-7142IP 2.8-12
OUTDOOR NETWORK IR DOME CAMERA
PACKING LIST
Name Q-ty
PE-7142IP 2.8-12 - OUTDOOR NETWORK
IR DOME CAMERA 1
CD disk:
1. Praxis IPC CMS
2. User Manuals for IP series Praxis
3. Video instructions
4. Helpful information
1
User Manual 1
SPECIFICATION
Image Sensor
Resolution
Min. Illumination
S/N
Lens
IR Status
Day/Night
Network
Delay
Frame Rate
1/3” SONY 2 Mpix CMOS HiSilicon
1920 X 1080
0.05 Lux
More 50db
2.8-12 mm / F 2.0
24PCS IR RANGE: 25 m
IR cut filter with auto switch, IR sensor.
1 RJ45 Ethernet 10/100 M
LAN 0.3S
2 Mpix / 25 FPS
Video Compression H.264 / JPEG
Protocol RTSP/FTP/PPPOE/DDNS/NTP
UPnP/TCP/SMTP
ONVIF ONVIF 2.4
User Permission Multi-user Classification Managment
Housing Metal outdoor IP66
Power 12 V DC / PoE
Current
Consumption 1А max
Dimension -
Weinght 800 g
Temperature -30 о С ~ +55 о С
SAFETY INSTRUCTION
Thank you for purchasing this Outdoor Network IR Camera
PRAXIS.
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Do not cut or peel off the cable.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electric-
ity limit.
10. Installation should be done by qualified service person only.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
Magnitude to constitute a risk of electric shock to persons.
The symbol is intended to alert the user to the presence of important operat-
ing and maintenance (servicing) Instructions in the literature accompanying
the appliance.
FEATURES
1. Support Single Stream, Dual Stream, TriStream
2. Support WEB Configuration, IE Surveillance
3. Support Android, IOS remote monitoring
4. Support Motion Detection Recording/ Capture upload via FTP/SMTP
5. Support DDNS
6. Support OSD,allowns to modify system time and IP Camera’s name
7. Support P2P
ACTIVATION
1.Open your IE browser.
2.Enter the IP addressdress:192.168.1.168.
Введите его в адресной строке вашего браузера.
3.Log on for the first time need to download and install the OCX
controls. When the installation is complete you will pop up the fol-
lowing tips.
4.Click OK, and then refresh the interface, Enter your account num-
ber and password, our default accounts: admin password: admin.
How to pass the “RTSP” access the IP camera
Download and install the VLC software.
Open the media, select open network stream.
VLC madia player 4 Media 4 Open Network Stream...
Input rtsp://192.168.1.168:80/0
Click Play, and then a password window will pop up.
Default username: admin
Default password: admin
Click OK.
Default IP of the IP camera is 192.168.1.168. If your computer is not in
the 192.168.1.xxx, you must be unified network segments, for example,
modifying the computer address or modify the IP camera.
PRAXIS IPС CMS FEATURES
1.Support the N organizational structure, management and user
access management.
2.To support the search device.
3.Support for displaying the front-end equipment list.
4.Support for multiple video window on the screen and the screen
control.
5.Support privacy covered.
6.Support capture.
7.Support motion dectect.
8.To support the client logs.
9.Support all kinds of small medium and large databases, such as
SOL, MYSQL and XML data.
10.Add and edit device support EXCEL software.
11.Support intelligent video transmission protocol.
12.Coordinated operation of multiple server support.
13.To support real-time monitoring and alarm video support, auto-
matic monitoring video recording, video playback
14.The support network and load balancing.
15.Support network upgrading.
16.DIY user interface and multi language support.
17.Support upload with SMTP and FTP.
18.Support plan videos record.
19.Support multi connected devices, video equipment.
20.Support for XML data storage.
TROUBLESHOOTING GUIDE
Restore the factory settings situation
1. Web port is changed and device can’t access Camera.
2. IP address is changed so that it can’t access Camera.
3. Other unknown reason so that it can’t access Camera.
Why does it shows “Get Param Failed”?
1.Please check the IP information, such as port.
2.Please make sure the IP Camera connected correctly.
3.The network status is poor.
Why screen get stuck, when we preview remote?
1.Network unstable (We need a better network).
2.Computer configuration is poor, For example, CPU or Graphics
card.
3.Simultaneous access to too many people.
4.Your camera frame rate and resolution of the problem.
Adding client equipment what are the issues that need atten-
tion?
In our client add device, manually entering the information must be
correct. If the camera working in LAN, you can search and add, but
you must pay attention to your user ID and password.
Why use Web pages can’t access IP camera?
1.The IPC input address errors.
2.Do not has install the corresponding OCX control.
3.The IPC logon account password error.
4. Relatively slow speed of the network or online more.
Why can not access the camera after update?
Clean browser cache. Steps: open IE, click “Tools” and select “Inter-
net Options”, then you can see “Temporary Internet files” and click
“Delete Files”, it will prompt a dialog you need to check “Delete all
offline content” and click “OK”. Also you can click “Start” and select
“Run” then enter “cmd”, enter “arp - d” in “Command Prompt”
interface. Re-access the camera.
Which one is the camera’s onvif port?
Our onvif ports: 80 or 8999.
CONNECTING
RJ45 Ethernet interface (VIDEO) (РоЕ)
12 V DC/1A
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE
PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN SPECIFIED POWER
SOURCE.

If the product is to be put out of operation definitively, take it to
a local recycling plant for a disposal which is not harmful to the
environment.
PE-7142IP 2.8-12
OUTDOOR NETWORK IR DOME CAMERA
PACKING LIST
Name Q-ty
PE-7142IP 2.8-12 - OUTDOOR NETWORK
IR DOME CAMERA 1
CD disk:
1. Praxis IPC CMS
2. User Manuals for IP series Praxis
3. Video instructions
4. Helpful information
1
User Manual 1
SPECIFICATION
Image Sensor
Resolution
Min. Illumination
S/N
Lens
IR Status
Day/Night
Network
Delay
Frame Rate
1/3” SONY 2 Mpix CMOS HiSilicon
1920 X 1080
0.05 Lux
More 50db
2.8-12 mm / F 2.0
24PCS IR RANGE: 25 m
IR cut filter with auto switch, IR sensor.
1 RJ45 Ethernet 10/100 M
LAN 0.3S
2 Mpix / 25 FPS
Video Compression H.264 / JPEG
Protocol RTSP/FTP/PPPOE/DDNS/NTP
UPnP/TCP/SMTP
ONVIF ONVIF 2.4
User Permission Multi-user Classification Managment
Housing Metal outdoor IP66
Power 12 V DC / PoE
Current
Consumption 1А max
Dimension -
Weinght 800 g
Temperature -30 о С ~ +55 о С
SAFETY INSTRUCTION
Thank you for purchasing this Outdoor Network IR Camera
PRAXIS.
1. Please study the instruction manual before your applications and
keep it for your future reference.
2. Do not flash LED light directly on the eyes when LEDs are on.
3. Do not install the camera on a unstable surface. It will cause falling
or other hazards.
4. Do not use improper power, it could cause fire or electric shock.
5. Do not disassemble or re-model the camera, it could cause fire,
electric shock or other hazards.
6. Stop using the camera when you find a malfunction like smoke or
unusual heat, it could cause fire or electric shock.
7. Do not cut or peel off the cable.
8. Do not adhere dangerous articles to the camera.
9. Please use the camera unit within given temperature and electric-
ity limit.
10. Installation should be done by qualified service person only.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
Magnitude to constitute a risk of electric shock to persons.
The symbol is intended to alert the user to the presence of important operat-
ing and maintenance (servicing) Instructions in the literature accompanying
the appliance.
FEATURES
1. Support Single Stream, Dual Stream, TriStream
2. Support WEB Configuration, IE Surveillance
3. Support Android, IOS remote monitoring
4. Support Motion Detection Recording/ Capture upload via FTP/SMTP
5. Support DDNS
6. Support OSD,allowns to modify system time and IP Camera’s name
7. Support P2P
ACTIVATION
1.Open your IE browser.
2.Enter the IP addressdress:192.168.1.168.
Введите его в адресной строке вашего браузера.
3.Log on for the first time need to download and install the OCX
controls. When the installation is complete you will pop up the fol-
lowing tips.
4.Click OK, and then refresh the interface, Enter your account num-
ber and password, our default accounts: admin password: admin.
How to pass the “RTSP” access the IP camera
Download and install the VLC software.
Open the media, select open network stream.
VLC madia player 4 Media 4 Open Network Stream...
Input rtsp://192.168.1.168:80/0
Click Play, and then a password window will pop up.
Default username: admin
Default password: admin
Click OK.
Default IP of the IP camera is 192.168.1.168. If your computer is not in
the 192.168.1.xxx, you must be unified network segments, for example,
modifying the computer address or modify the IP camera.
PRAXIS IPС CMS FEATURES
1.Support the N organizational structure, management and user
access management.
2.To support the search device.
3.Support for displaying the front-end equipment list.
4.Support for multiple video window on the screen and the screen
control.
5.Support privacy covered.
6.Support capture.
7.Support motion dectect.
8.To support the client logs.
9.Support all kinds of small medium and large databases, such as
SOL, MYSQL and XML data.
10.Add and edit device support EXCEL software.
11.Support intelligent video transmission protocol.
12.Coordinated operation of multiple server support.
13.To support real-time monitoring and alarm video support, auto-
matic monitoring video recording, video playback
14.The support network and load balancing.
15.Support network upgrading.
16.DIY user interface and multi language support.
17.Support upload with SMTP and FTP.
18.Support plan videos record.
19.Support multi connected devices, video equipment.
20.Support for XML data storage.
TROUBLESHOOTING GUIDE
Restore the factory settings situation
1. Web port is changed and device can’t access Camera.
2. IP address is changed so that it can’t access Camera.
3. Other unknown reason so that it can’t access Camera.
Why does it shows “Get Param Failed”?
1.Please check the IP information, such as port.
2.Please make sure the IP Camera connected correctly.
3.The network status is poor.
Why screen get stuck, when we preview remote?
1.Network unstable (We need a better network).
2.Computer configuration is poor, For example, CPU or Graphics
card.
3.Simultaneous access to too many people.
4.Your camera frame rate and resolution of the problem.
Adding client equipment what are the issues that need atten-
tion?
In our client add device, manually entering the information must be
correct. If the camera working in LAN, you can search and add, but
you must pay attention to your user ID and password.
Why use Web pages can’t access IP camera?
1.The IPC input address errors.
2.Do not has install the corresponding OCX control.
3.The IPC logon account password error.
4. Relatively slow speed of the network or online more.
Why can not access the camera after update?
Clean browser cache. Steps: open IE, click “Tools” and select “Inter-
net Options”, then you can see “Temporary Internet files” and click
“Delete Files”, it will prompt a dialog you need to check “Delete all
offline content” and click “OK”. Also you can click “Start” and select
“Run” then enter “cmd”, enter “arp - d” in “Command Prompt”
interface. Re-access the camera.
Which one is the camera’s onvif port?
Our onvif ports: 80 or 8999.
CONNECTING
RJ45 Ethernet interface (VIDEO) (РоЕ)
12 V DC/1A
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE
PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN SPECIFIED POWER
SOURCE.