Premier Mounts IPM-53 User manual

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com
iPad™ IPM-530 Tabletop Stand and Wall Mount Installation Instructions
9531-056-061-00
Parts List
IPM-530
iPad™ Frame
(Qty 1)
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada
Phone: [phone]
Fax: [phone]
Other Locations – Phone: [phone]; Fax: [phone] ©Premier Mounts 2011
The IPM-530 tabletop stand and wall mount securely holds the Apple
iPad™ or iPad2™ (not included) in place and gives access to all
iPad™ controls and connections. Attach the removeable back plate to
the base, then rotate the mount for landscape or portrait placement.
The mounting base can be placed freely on a tabletop, or drilled into
it with wood screws. The base can also be mounted to a wood stud or
surface..
• All trademarks are the property of the respective trademark owners.
#8 x 1¼” Wood Screw
(Qty 4)
IPM-530 Mounting Base
(Qty 1)
Push-In Rivet
(Qty 4)
Step 1
Remove the back plate from the
iPad™ frame.
Step 2
Are you installing an original
iPad™ or iPad2™ to the
IPM-530?
If an original iPad™, remove
the corner felt pads on the
iPad™ frame. Then continue
to step 3.
If an iPad2™, continue to
step 3.
Remove if using original iPad™
Remove if using original iPad™
Step 3
➊Extend the arms of the iPad™
frame.
➋Insert the iPad™ in the iPad™
frame.
Each arm of the iPad™ frame
should t over a corner of the
iPad™.
Continue to Step 4 on page 2.
10-32 x ¼”
Flat Phillips Screw
(Qty 2)

Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
IPM-530
IPM-530 Installation Instructions (cont’d)
Step 5
Are you using the IPM-530 as a
tabletop or wall mount?
If tabletop mount, use two (2)
10-32 x ¼” at Phillips screws
to attach the back plate (pointed
side up) to the mounting base
(Figure 1).
If wall mount, use two (2)
10-32 x ¼” at Phillips screws
to attach the back plate (pointed
side down) to the mounting base
(Figure 2).
10-32 x ¼” Flat Phillips Screw
Step 4
➊Adjust the arms on the iPad™
frame so that the iPad™ ts
snuggly inside the mount (Figure
1).
➋Tighten the two (2) pre-installed
Phillips screws on the back of
the iPad™ frame to secure the
arms (Figure 2).
Mounting tab on IPM-530
Figure 1
Figure 2
Phillips screws
10-32 x ¼” Flat Phillips Screw
Step 6
Choose one of the following installation options:
• If freestanding tabletop mount, continue to Freestanding Tabletop
Installation below.
• If swivel tabletop mount, go to Swivel Tabletop Installation on page 3.
• If wood stud installation, go to Wood Stud Installation on page 3.
• If wood surface installation, go to Wood Surface Installation on page 4.
Freestanding Tabletop
Installation
➊Insert the iPad™ frame into
the back plate on the mounting
base.
➋Rotate the mount to the desired
landscape or portrait position.
➌Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Figure 1
Figure 2

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
IPM-530 Installation Instructions (cont’d)
IPM-530
Swivel Tabletop Installation
➊Replace the bumpers on the
bottom of the mounting base
with four (4) push-in rivets
(Figure 1).
➋Determine where you want to
secure the mounting base.
➌Insert one (1) #8 x 1¼” wood
screw through a bottom screw
hole on the mounting base and
into the table (Figure 2).
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 3).
➎Rotate the mount to the desired
landscape or portrait position.
➏Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Figure 1
Figure 2
Push-in rivet
Wood screw
Figure 3
Wood Stud Installation
➊Determine where you want to
attach the mounting base to the
wood stud.
➋Insert two (2) #8 x 1¼” wood
screws through the bottom
screw holes on the mounting
base and into the stud
(Figure 1).
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 2).
➎Rotate the mount to the desired
landscape or portrait position.
➏Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Wood screw
Figure 1
Figure 2

Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
IPM-530
IPM-530 Installation Instructions (cont’d)
Wood Surface Installation
➊Determine where you want to
attach the mounting base to the
wood surface.
➊Remove the bumpers from the
bottom of the mounting base.
➋Insert four (4) #8 x 1¼” wood
screws through the corner holes
on the mounting base and into
the wood surface (Figure 1).
The corner holes are where the
bumpers used to be.
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 2).
➎Rotate the mount to the desired
landscape or portrait position.
Wood screw
Figure 1
Figure 2
Technical Specications
.67
17.12
5.83
147.99
5.91
150
5.91
150
6.00
152.40
1.35
34.29
5.07
128.85
2.62
66.55
4.80
121.92
All measurements are in inches [millimeters].