Primera 510690-032808 Specifications

SECTION II: CREATING DISCS
1. 80mm Discs can be produced in the same manner as standard
120mm discs.
When printing Hockey Rink or Business Card
discs on the PC, it is necessary to record and print the cards
in two separate steps. To record, first load the input bin with
blank CD-R Business Cards. Next, create your recording job as
described in the User’s Manual making sure to leave the print step
blank in PTPublisher. On the Mac, you have the option in Discribe
to print before recording, which will allow you to make the cards
unattended.
2. Once your Business Cards have finished recording, reload them in
the input bin for printing. When printing one of the three sizes
supported by this adapter kit, you will need to select the proper card
size in the driver as shown below. Simply print the number of
desired copies. When printing only from SureThing or any
application the unit will automatically load and unload the discs.
Supported Sizes:
- Mini-disc CDs - 80mm (201 MB)
- Business Card CDs - 59mm x 85mm (32 MB)
- Hockey-Rink CDs - 63mm x 80mm (49 MB)
PN 510690-032808
Operator Instructions:
Business Card Adapter Kit
For Use with Disc Publisher II, Disc Publisher XR or
AutoPrinter II
Two Carlson Parkway North •Plymouth, MN 55447-4446 •U.S.A.
Phone: [phone] •763-475-6676 •FAX: [phone]
Web: www.primeratechnology.com
Page Size Settings
for PC Page Size Settings
for Mac

This manual describes the installation and use of the CD-R Business
Card Adapter Kit for the Disc Publisher II, XR and AutoPrinter II
(referred to hereafter as the “Unit”).
NOTE: The Business Card Adapter Kit is designed to work with the
above units only. If you have the Disc Publisher Pro, please use the Pro
kit.
SECTION I: INSTALLATION
1. Make sure that you have the following items in this box:
•CD Business Card/ Mini CD 80mm Input Bin
•“Hockey Rink” Card Input Bin
•Output Ring
•CD Business Card Tray Template Assembly
•Mini Disc 80mm and “Hockey Rink” Tray Template Assembly
•9 Sample Discs
•Drive Templates for use with DVD units with serials numbers
greater than 2060600000, when burning hockey rink or business
card discs.
2. Remove original 120mm Input Bin and place the appropriate Card/
Mini Disc Input Bin on the right side of the unit with the opening in
the bin to the rear.
If the opening in the bin is not toward the
rear, the Robotic Disc Transporter will not be able to pick
from the bin.
Figure 1: Input Bins
3. Place Output Ring in the center of the Output Bin on the left side
of the unit as shown in Figure 3.
4. With the Front Cover of the unit closed, press the Cartridge
Button. The Printer Tray will open. Open the Front Cover and
install the appropriate Printer Tray Template in the Printer Tray
as shown in Figure 3. The front of the Template has molded tabs
that fit into locating slots found toward the front of the Printer
Tray. When properly installed, the metal clamp moves forward to
hold the card in place as the Printer Tray retracts into the printer.
Figure 3: Adapter Kit
5. Press the eject button to open the DVD drive. Place the Business
Card or Hockey Rink template into the tray. The templates are labeled
“Hockey Rink” or “Business Card”. For best results, it may be necessary
to remove the strips of tape that are affixed to the bottom of the drive
tray.
Important Note: Step 5 is only necessary if you have a DVD unit with
a serial number greater than 2060600000 and you are burning Hockey
Rink or Business Card discs. 80 mm discs do not require this step.
“
Hockey Rink” Card Input Bin CD Business Card/ Mini CD
Input Bin
Rear Opening
For Arm
“Hockey Rink” and Business
Card Template Mini Disc Template
Figure 2: Printer Tray Templates
Output
Ring
Input Bin
Printer Tray
Template
Front Cover
Cartridge
Button