PrioVino Classic User manual

PrioVino Classic
Operating Instructions
Status: December 2018
First edition December 2018 / © PrioVino GmbH
Reprint – even in extracts – only upon written
permission by PrioVino GmbH (ISO 16016).

2
Contents
1. General information
1.1 Information about these operating instructions
1.2 Safety warnings
1.3 Limitation of liability
2. Safety
2.1 Proper use
2.2 General safety instructions
2.3 Safety instructions for power supply, battery
and battery charger
3. Before use
3.1 Unpacking the device
3.2 Parts and accessories included
3.3 Names of working parts
3.4 Correct placement of the device
3.5 Checking electrical connections
3.6 Charging the battery (only applicable for the
battery-operated version)
4. Set-up and operation
4.1 Operation on mains power
4.2 Operation on battery
4.3 Setting the desired temperature
5. Cleaning instructions
6. Storage
7. Service and maintenance
8. Disposal
9. Technical information
10. Declaration of conformity
The reproduction, distribution and utilization of this document as well as the
communication of its contents to others without express authorization is prohibited.
Oenders will be held liable for the payment of damages. All rights reserved in the
event of the grant of a patent, utility model or design.
– Refer to protection notice ISO 16016 –

3
1. General Information
1.1 Information about these operating instructions
These are the operating instructions for the wine cooler PrioVino Classic
(hereafter referred to as the device). It provides important information for
the safe operation of the device and must be carefully studied by anyone
who sets up, operates or cleans it. Non-compliance with the instructions
laid out in this manual can lead to injuries to the user and/or damage to
the product. Please keep the user manual at a safe and easily accessible
location at the operation site of the device.
You can download the operating instructions from our website at
www.priovino.com/downloads, where it is also available in additional languages.
Content and technical specications are subject to change without notice.
1.2 Safety warnings
indicates a warning about situations that could lead to serious injury
or constitute a re hazard.
indicates a warning about situations that could be hazardous
to the user or cause product damage.
1.3 Limitation of liability
The information, facts and gures, diagrams and technical instructions
contained in these operating instructions were compiled with the utmost
care in order to make the set-up, operation and cleaning of this device safe
and easy. Illustrations may be exemplary.
The manufacturer assumes no liability for damage or injury caused by
non-compliance with the instructions in these operating instructions as well
as for any damage caused due to improper repairs, technical modications
to the device or the use of third-party spare parts.
All translations of these operating instructions were carried out by
professional translators. The manufacturer assumes no liability for damage
or injury caused by incorrect translations. If in doubt, please refer to the
original operating instructions.
– Refer to protection notice ISO 16016 –

4
2. Safety
This device complies with all statutory safety regulations. However,
the improper use of the device may lead to injuries, material damage or
damage to the product.
2.1 Proper use
Use the device only for the intended purpose. Improper use or
non-compliance with these operating instructions can have very
dangerous consequences.
2.1.1 Personnel requirements
The device may only be operated by authorized personnel, qualied under
local regulations, and duly instructed and trained by the owner of the device.
The owner of the device is obliged to inform the operating personnel about
changes to the device and to train them if necessary.
2.1.2 Intended scope of operation
The device is only intended to maintain the temperature of pre-cooled wine
bottles with a diameter of not more than 9.4 cm and is designed mainly for
commercial use. The intended temperature range for the bottle is 5°C – 20°C.
The device may only be operated in technically awless condition and in
a proper, safety-conscious and risk-conscious manner in accordance with
the operating instructions! Immediate attention is particularly important
where malfunctions pose a safety risk! Proper use includes close adherence
to the operating instructions as well as compliance with the maintenance
regulations and schedules.
The device is designed for the environmental conditions described in
section 9 “Technical information“.
Modications to the device require written approval by PrioVino GmbH.
Any retrotting of the device must be carried out and tested by
PrioVino GmbH prior to use.
– Refer to protection notice ISO 16016 –

5
2.1.3 Unauthorized area of operation – foreseeable misuse
A dierent use or a use that exceeds the intended scope of operation
described in 2.1.2 is considered improper. PrioVino GmbH is not liable
for any resulting damage. The risk is solely borne by the operator.
The device is not designed to cool down or heat up wine bottles.
In particular, it is not permitted to misuse the device e.g. as a shelf, coat
stand or standing aid. It is also not allowed to introduce liquid into the
bottle opening – even for cleaning purposes.
2.2 General safety instructions
• Inspect the device before use and do not switch it on if there is
any visible external damage.
• Children may not operate or be left unattended with the device.
• Injuries could result from the falling or toppling over of the cooler
or its stand.
• The device may only be operated by persons with mental,
physical or sensory impairments if they have been instructed about
the safe operation of the device as well as possible dangers or
if they are supervised.
2.3 Safety instructions for power supply, battery and battery charger
Depending on which version of the device is used, it can be operated on
a battery or on mains power.
Please observe the following safety instructions in order to avoid
dangerous situations:
• Do NOT touch the battery charger or any of the plugs or electrical
connections with wet hands.
• If you notice any damage to the plugs or connecting cables,
do NOT switch on the device, and contact our service department
immediately so that the damaged part can be repaired or replaced.
• Do NOT open the device, as parts in the interior of the device
could be current-carrying. Changing the electrical or mechanical
design of the device can result in severe electric shocks or
device malfunctions.
– Refer to protection notice ISO 16016 –

6
• Do NOT submerge the device in water or any other uid.
• The device is NOT dishwasher safe.
• Please ensure that the air vents are always free of any blockages.
Do not cover the air vents because this may cause the build-up
of heat and create a re hazard.
• Do NOT insert any objects into the air vents. Contact with current-
carrying parts in the interior of the device will lead to electric shock.
3. Before use
3.1 Unpacking the device
• Take the device out of the outer carton and remove all accessories
from the packaging material.
• Packaging material is not a toy. Please do NOT allow children to play
with packaging materials in order to avoid the danger of suocation.
• After unpacking, please check that the delivery is complete and without any
visible damage. Please contact us immediately if you receive an incomplete
or damaged delivery.
• Keep the outer carton and packaging materials in a safe place so that
you can return the product to us in its original packaging, should this ever
become necessary.
3.2 Parts and accessories included
• Cooler
• Power supply
• Battery charger (if applicable)
– Refer to protection notice ISO 16016 –

7
3.3 Names of working parts
handles
bottle chamber
Cooler
air vents
LED low battery alert
User interface
on/o
button
temperature
display
set button plus/minus buttons
to set temperature
– Refer to protection notice ISO 16016 –

8
Battery charger
Power supply
charger plug
operating plug
power cord with C8 plug
at one end and the electrical
plug on the other
power cord with C13 plug
at one end and the electrical
plug on the other
socket for
C8 plug
socket for
C13 plug
OR
– Refer to protection notice ISO 16016 –

9
3.4 Correct placement of the device
• Ensure that the device is placed on a rm, even and perfectly
horizontal surface with sucient load-bearing capacity.
• Do NOT place the device in a damp or wet environment, or close
to open replaces or hearths.
• Make sure that the power supply/battery charger is not covered
and ensure that there is enough space between the power
supply/battery charger and other objects. If heat is allowed to
build up around the power supply/battery charger, it could result
in a re hazard.
We would be happy to provide consultation about the correct placement
of the device on ships, aircraft, or other non-stationary surfaces. Please
contact us for more information.
3.5 Checking electrical connections
Before you connect the device to a mains power source, compare the
voltage and frequency of the power supply/battery charger with that of the
power source. In order to prevent damage or malfunctioning of the product,
these values must match. The type plate on the power supply/battery
charger displays the relevant specications.
In addition, please note the following:
• The electrical outlet to which the power supply/battery charger is
connected must be protected by a circuit breaker (minimum 10 A).
• The device may only be connected to a mains power source with the
power cord included in your delivery. Do NOT plug the device into a
multiple power outlet or power strip as this can lead to a re hazard due
to overload.
• Ensure that the power cord does not lie over or under a hot or sharp-
edged surface.
3.6 Charging the battery (only applicable for the battery-operated version)
The battery should be fully charged before you rst switch on the device.
The battery should only be charged with the battery charger supplied with
the device.
• To charge the battery, insert the charger plug of the battery charger into
the socket underneath the cooler.
• Use the power cord to connect the battery charger to the electrical outlet.
This will cause the lower LED to light up in red.
– Refer to protection notice ISO 16016 –

10
• The upper green LED will ash while the battery is charging and
stop ashing once charging is complete.
• Disconnect the battery charger from mains power.
• Disconnect the battery charger from the cooler.
• If the upper LED lights up red or begins to ash in red, this is an
indication of a malfunction. Discontinue the charging process
immediately by removing the power plug from the electrical outlet
and then contact our service department.
4. Set-up and operation
This device can be run on mains power or depending on the model,
it can also be powered by a rechargeable battery.
4.1 Operation on mains power
• Connect the power supply/battery charger to the cooler by plugging in the
operation plug/charger plug in the socket on the underside of the cooler.
• Connect the power cord/charger cable to the power supply/battery
charger using the C13/C8 plug.
• Connect the power supply/battery charger to the electrical outlet using
the power plug.
4.2 Operation on battery
• Once the battery has been fully charged, the device is ready to be
switched on.
• When the battery is down to about 15% of full capacity, a blue LED lights
up behind the air vents. This low battery alert is a reminder to charge the
battery by plugging the device into mains power.
Turn the device o when it is not in use to avoid unnecessary power
consumption or battery drain.
4.3 Setting the desired temperature
• To switch the device on, press the on/o button until the blue
temperature display lights up.
• To set the desired temperature, rst press the set button. The display will
begin to ash.
• Use the plus/minus buttons to set the temperature you require.
– Refer to protection notice ISO 16016 –

11
• Then press the set button once again to conrm the temperature setting.
The display will stop ashing and your desired temperature will be
indicated in the temperature display.
• Insert the pre-cooled wine bottle into the bottle chamber.
5. Cleaning instructions
To prevent damage to the device and to protect the exterior from scratches,
we recommend regular cleaning and care. Before cleaning, please switch
o the device and disconnect it from mains power.
Please follow the cleaning guidelines outlined below:
• Wipe the device with a soft, damp cloth. Make sure you dry the device
thoroughly after cleaning.
• Do not use aggressive or abrasive cleaning products or solvents of any
kind, such as petroleum.
• Ensure that no water or humidity gets into the interior of the device
through the air vents while cleaning.
• Do NOT submerge the device in water or any other uid.
• This device is NOT dishwasher safe.
6. Storage
When storing the device overnight, please make sure that the device has
been disconnected from mains power before storing it in a safe and dry
location. When storing for longer periods of time, please ensure that the
device is kept in a safe, dry and dust-free location.
7. Service and maintenance
Repairs or maintenance on this device should be carried out solely
by PrioVino technicians. Improper repairs or maintenance can cause
damage to the product and represent signicant danger to the life
and well-being of the user.
For your own safety and to avoid malfunctions in the device, only use
original spare parts supplied by PrioVino GmbH.
– Refer to protection notice ISO 16016 –

12
When making your request for repairs or maintenance on the device,
please include the product identication number. This number can be found
on the underside of the cooler.
8. Disposal
If you need to dispose of the device, the battery or the battery charger,
please do so in accordance with local ordinances and regulations for
the proper disposal of electrical and electronic equipment.
9. Technical information
Device Electrical wine cooler
Model Classic
Temperature range 5°C – 20°C
Temperature intervals 1°C
Bottle opening 9.4 cm diameter
Height 28 cm
Total weight (without battery) 2.2 kg
Battery charger input 220 – 240 V/50 – 60 Hz
Depending on the model:
Power supply output 12 V/5 A
Battery charger output 12.3 V/4 A
Permissible environmental 5°C – 40°C
conditions for operation 15% – 85% relative humidity
(non-condensing)
Emission sound pressure level < 70 dB(A)
– Refer to protection notice ISO 16016 –

13
10. Declaration of conformity
The device complies with EC Directive 2006/42/EC and EU Directives
2011/65/EU and 2014/30/EU.
For details, refer to the complete declaration of conformity on page 14/15.
– Refer to protection notice ISO 16016 –
Manufacturer and service address
PrioVino GmbH
Eschenweg 21
72076 Tübingen
Phone: [phone]
Fax: [phone]
Email: inf[email protected]
Internet: www.priovino.com

14
EC Declaration of conformity
According to EC Directive 2006/42/EC, Annex II 1. A
We hereby declare,
PrioVino GmbH, Eschenweg 21, 72076 Tübingen
that the device referred to as
Designation: Wine coooler
Type: Classic MA / 101
Year of construction: as of 2018
complies with EC Machinery Directive 2006/42/EC.
The device also complies with the following directives:
2006/66/EC 2011/65/EU 2014/30/EU
2014/35/EU: The protection goals of the directive were maintained
according to Appendix I, No. 1.5.1, 2006/42/EC.
The following harmonised standards have been applied:
DIN EN 60335-1:2012-10 + DIN EN ISO 13732-1:2008-12
B1:2014-04 + B2:2014-11 DIN EN ISO 13732-3:2008-12
DIN EN ISO 12100:2011-03 + B1:2013-08 DIN EN ISO 13857:2008-06
The following national or international standards (or parts/clauses thereof) and
specications have been applied:
DIN ISO/TR 14121-2:2013-02
Responsible for the assembly of the technical documents:
Moritz Ortwein, PrioVino GmbH, Eschenweg 21, 72076 Tübingen
Date: 04.12.2018
Revision: A
Date Moritz Ortwein, Technical Director
04.12.2018Tübingen,

EC Declaration of conformity
According to EC Directive 2006/42/EC, Annex II 1. A
We hereby declare,
PrioVino GmbH, Eschenweg 21, 72076 Tübingen
that the device referred to as
Designation: Wine coooler
Type: Classic OA / 101
Year of construction: as of 2018
complies with EC Machinery Directive 2006/42/EC.
The device also complies with the following directives:
2011/65/EU 2014/30/EU
2014/35/EU: The protection goals of the directive were maintained
according to Appendix I, No. 1.5.1, 2006/42/EC.
The following harmonised standards have been applied:
DIN EN 60335-1:2012-10 + DIN EN ISO 13732-1:2008-12
B1:2014-04 + B2:2014-11 DIN EN ISO 13732-3:2008-12
DIN EN ISO 12100:2011-03 + B1:2013-08 DIN EN ISO 13857:2008-06
The following national or international standards (or parts/clauses thereof) and
specications have been applied:
DIN ISO/TR 14121-2:2013-02
Responsible for the assembly of the technical documents:
Moritz Ortwein, PrioVino GmbH, Eschenweg 21, 72076 Tübingen
Date: 04.12.2018
Revision: A
Date Moritz Ortwein, Technical Director
04.12.2018Tübingen,
15

PrioVino GmbH
[phone]
[e-mail]
www.priovino.com