progressive automations NY-08 User manual

Page 1
USER’S GUIDE
Model: NY-08
TV Wall Mount
1. Specification
1-1. Dimension
Length: 27.8 in
Height: 10 in
Width: 17.7 in
1-2. Installation Parts:
1.3 Assembly tools (NOT INCLUDED)
Check all the parts as shown on the manual included .If parts are missed or damaged, do not use
it and please return to your local distributor.

Page 2
USER’S GUIDE
Warning:
Correct installation is extremely essential , and falls outside the scope of responsibility of
manufacturer . The user must pay attention to the weight of TV and TV wall mount, and only solid
wall can support the weight. For the wooden wall, product’s fasteners supplied shall be positioned
in wood stubs. Please comply with the installation instruction of LCD/PDP to install them.
3. Installation Instruction
3-1. Be sure the wall to be mounted is solid
enough and does not have rigid material
inside and he wall thickness at least 80mm.
Then,put the mounting panel on the wall,
horizontalize it and mark hole locations.
(Stage 1)
3-2. Drill holes on the wall at marked
locations to 75mm depth and Ø 10mm, put
(6) expansion screw (4PCS) to the holes,
and tighten them with hammer and spanner.
(Stage 2)
2-2. Motor
Item Rated
Voltage
Current
(No load)
Current
(Rated load)
Operation
Temperature
Motor DC12V ≤ 0.3 A ≤ 0.6 A -20 C ~ -50 C
2. Electric Specification
2-1. Input voltage/Current/Frequency, Output current
A. Input voltage/Current/Frequency: 110-240VAC/< 0.65A/50~60Hz
B. Output current: DC12V , 2A

Page 3
USER’S GUIDE
3-3. Insert square tube (2pcs)into the holes
of the conjuctive rack, let the stamped lines
on the quare tubes close to the edge of
conjunctive racks.
Screw up the (7) plastic-head screws behind
the conjunctive rack to fasten square tube.
Finally,hang TV brackets (2pcs) on the
square tubes and tighten them by (7) plastic-
head screws. (Stage 3)
3-4. Screw up (2) hooking tabs (2pcs) to
the upper side of TV back cover by (1) sink
head screws (2pcs).
Hook TV to TV bracket to the corresponding
holes by the tabs. (Stage 4)
3-5. Screw up TV brackets to the lower end
of TV back cover by (3) round head screw
with (4) washer and (5) pad. (Stage 5)

Page 4
USER’S GUIDE
3-6. With the help of
another person , hook
TV bracket (with TV) to
the hooking gap of the
mounting panel, then
tighten (7) plastic head
screw. (Stage 6)
3-7. Fix the power cord
of TV Please use the wire
saddle to x the power
cord of TV.
Finally,insert the end of
adapter into the power
supply interface onTVwall
mount and connect the
other end to the power
supply.( Stage 7)
4. User's Guide
A. Function
This product can be controlled by remote control to adjust the angle of TV to pitch up 10° and pitch
down 15°, turn left or right 15°. (stage 8)

Page 5
USER’S GUIDE
II. Operating Instruction
1. Insert one 23A12V battery in the remote control, the remote range is within 15 meters.
2. Press and hold on the direction key (up, down, left, right) to turn TV to proper angle.
III. Notice
If any remote control of our product was lost or damaged ,you can buy a new remote control with
the same frequency which produce by our company and do following operation:
1. Memory cleaning: Press coding key about 10 seconds, the memory will clean after the LED
indicator closed. (The memory is the coding memory of the previous remote control).
2. Use new remote control: Press any key of remote control and the coding key1-2 seconds at the
same time, Loosen remote control rstly, Then loosen the coding key.
Finally, you can operate the product with new remote control. (Coding key ,Indicator, Please see
stage 3).
B. Remote Control (Stage 9):
I. Key Function
1. Up : Hold on to pitch TV up.
2. Down : Hold on to pitch TV down.
3. Left : Hold on to turn TV left.
4. Right : Hold on to turn TV right.

Page 6
USER’S GUIDE
7. Maintenance
7-1. Do not use corrosive agent or alcohol or chemical cloth to clean!
7-2. Temperature and humidity condition: -20 C - +50 C, 80%HR
Warning:
1. Do not disassemble the product to repair by yourself .warranty for electricity is void after
disassembled!
2. After you installed the apparatus, please check the expansion screws and all fastening devices
every 3 months , and please do not useit and contact the local dealer if it gets loose, rusty or
lost.
Item
Model
TV Screen
Size (inch)
Cart
Dimension
Max Installation
Size (inch)
Min Installation
Size (inch)
Load
(lbs)
L/R
angle ()
Up & Down
angle ()
Net
Weight (lbs)
NY-08 25~46” 27.8”x
17.7”x10”
23.6 x 15.7 7.87 x 7.87 176.4 15 Up 10
Down 15
29 0.5
CAUTION:
This wall mount is intended for use only with the maximum weights indicated . Use with heavier an
the maximum weights indicated may result in instability causing possible injury.
5. Technical Parameters:
6. Notice: