ProLights ARENACOB4FC User manual

MANUALE UTENTE
USER MANUAL
ARENACOB4FC
IT - EN
LED BLINDER

1
ARENACOB4FC
Packing content ARENACOB4FC
• Mount bracket
• Power cable
• User manual
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
General information
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 DIMMER
3. 5 Back Light
3. 6 Information mode
3. 7 White Balance
3. 8 Key Lock
3. 9 Master/Slave mode
3. 10 Linking
3. 11 DMX mode
3. 12 DMX addressing
3. 13 Connection of the DMX line
3. 14 Construction of the DMX termination
3. 15 DMX control
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Fuse replacement
4. 3 Trouble shooting
Warranty
2
2
3
4
4
7
8
9
9
10
10
10
10
11
11
11
11
13
13
15
15
16
21
21
21

ARENACOB4FC
2
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the xture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 40 °C.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Do not dismantle or modify the xture.
• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
• Always additionally secure the projector with the safety rope.When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the xture’s being used.
• Install the xture in a well ventilated place.
• Keep any inammable material at a safe distance from the xture.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.

3
ARENACOB4FC
GENERAL INFORMATION
Shipments and claims
The goods are sold “ex works” and always travel at the risk and danger of the distributor. Eventual dam-
age will have to be claimed to the freight forwarder. Any claim for broken packs will have to be forwarded
within 8 days from the reception of the goods.
Warranty and returns
The guarantee covers the xture in compliance with existing regulations. You can nd the full version of
the “General Guarantee Conditions” on our web site www.musiclights.it. Please remember to register the
piece of equipment soon after you purchase it, logging on www.musiclights.it. The product can be also
registered lling in and sending the form available on your guarantee certicate. For all purposes, the va-
lidity of the guarantee is endorsed solely on presentation of the guarantee certicate. Music & Lights will
verify the validity of the claim through examination of the defect in relation to proper use and the actual
validity of the guarantee. Music & Lights will eventually provide replacement or repair of the products de-
clining, however, any obligation of compensation for direct or indirect damage resulting from faultiness.

ARENACOB4FC
4
- 1 - INTRODUCTION
1.1 DESCRIPTION
ARENACOB4 FC is a proper, full color replacement for an“old school”4 cell Blinder.
Each of the ARENACOB4 FC’s 100W RGBW LED Pods deliver a consistent, powerful punch with indivodual con-
trol of each cell. The clever rigging system allows the creative freedom to use the xture as a building block
oering virtually limitless possibilities.
With an IP54 housing, magnetic lens options, individual control of each LED cell, clever rigging system and cell
spacing that matches a standard blinder the ARENACOB4 is not only powerful but also unbelievably exible.
1.2 TECHNICAL SPECIFICATIONS
Light source
• Source: 4x75 W RGBW LEDs
• Luminous Flux: 5726lm
• Lux: (24°) 2413lux @3m Full
• Source Life Expectancy: >50.000 h
OPTICS
• Beam Angle: (inc) 24° - (opt) 40°
• Field Angle: 42°
• Pixel pitch: 150mm
• Lens Diameter: 100mm
• Lens Type: Dichroic parabolic reector in combination with HD fresnel lens
• Additional Optics: 40°(opt), 32° without magnetic lens
• Magnetic replacement of front lens
COLOR SYSTEM
• Color Mixing: RGBW/FC
• CTC: CTC control through independent DMX channel
• White Presets: 2000~8000K
• Color Wheel: Virtual color wheel with presets
DYNAMIC EFFECTS
• Pixel Patterns: Preprogrammed dynamic and static patterns
• FX Generator: Adjustable foreground/background color, index, speed, direction
• Static Color Mode: Selection of static color
• Manual Color Mode: Manual adjustment of color
• Auto Mode: Built-in programs with execution speed adjustment
• Halo DWE dimming and amber-shift simulation
BODY
• Hardware On-board: On board mechanics for modular assembly of multiple panels
• Body: Sturdy die-cast aluminium body conceived for long-time durability
• Body Color: Black
CONTROL
• Protocols: DMX, RDM
• Dmx Channels: HALO 1/4ch - STD 4/6/15ch - EXT16/21/27ch
• Pixel Control: Pixel2Pixel control
• RDM: RDM ready for xture remote monitor and settings
• Display: Black OLED touch display
• Firmware Upgrade: Yes, via USB-DMX interface (UPBOX1) not included

5
ARENACOB4FC
• Master/Slave: for synchronized operation of more units linked in a chain
ELECTRONICS
• Dimmer: Linear 0~100% electronic dimmer
• Dimmer Curves: 4 Dierent dimming curves available
• Strobe/Shutter: 1-28 Hz, electronic
• Battery Backup: Battery backup for user operation without connecting to the main power
• Operating Temperature: -10/45°
• Flicker: Flicker free frequency
ELECTRICAL
• Power Supply: 100-240V – 50/60Hz
• Power Consumption (at 230V): 227W
• Power Consumption (at 120V): 230W
• Power Output (at 230V): 15 units on a single power line
• Power Output (at 120V): 7 units on a single power line
PHYSICAL
• Signal Connection: 5p IP in/out
• Power Connection: Seetronic Powerkon IP54 in/out
• IP: 54 Protective vent to prevent condensation, dust, compensate pressure
• Cooling: Natural cooling of the peculiar chassis and to absence of fans
• Suspension And Fixing: Hanging bracket suitable for safe hanging and for oor positioning
• Dimensions (WxHxD): 619x167x264mm
• Weight: 7,9Kg
Fig.1
Photometric data
Technical drawing
264.4
619
167
Illuminance at a Distance
24°-RGBW
0m
1.0m
3.0m
5.0m
7.0m
10.0m
1.22m
0.41m
2.03m
2.85m
Lux Center Beam Angle: 23° Beam Width
3167lx
28505lx
1140lx
581.7lx
4.07m285lx

ARENACOB4FC
6
1.3 OPERATING ELEMENTS AND CONNECTIONS
1. LOCKING KNOB for the mounting bracket
2. POWER IN (PowerCON TRUE IN): for
connection to a socket (100-240V~/50-60Hz)
via the supplied mains cable.
3. DMX IN (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C
4. CONTROL PANEL with display and 4 button
used to access the control panel functions
and manage them
5. DMX OUT (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C
6. POWER OUT (PowerCON TRUE OUT): power
output for connection of multiple units in
series.
7. SCREW-IN PROTECTIVE VENTS
Rear panel Fig.2
7
12 3 4 5 6

7
ARENACOB4FC
- 2 - INSTALLATION
2.1 MOUNTING
ARENACOB4FC may be set up on a solid and even surface. More units can also be mounted together with
the included hardware (max 10 pcs for each column). For xing, stable mounting clips are required. The
mounting place must be of sucient stability and be able to support a weight of 10 times of the unit’s
weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
garding safety) currently in force in the country in which the xture’s being used.
• Install the projector at a suitable location by means of the mounting bracket (2).
• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-
ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.
• Adjust the projector and use the screw to slightly release or tighten the locking mechanism of the
bracket if is necessary (1).
Fig.3
1
2
MAX 10 pcs
CLAMP
SAFETY
ROPE
ARENACOB4FC

ARENACOB4FC
8
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation
and can be operated via a DMX controller or it independently performs its show program in succession.
To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-
mended to connect the unit to a socket which can be switched on and o via a light switch.
3.2 BASIC
Access control panel functions using the four panel buttons located directly underneath the black OLED
display (g.4).
Fig.4 - Functions of the buttons
MODE UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in
a function
Used to select and store the
current menu or conrm the
current function value or
option within a menu
Mode
Enter
Up
Down

9
ARENACOB4FC
3.3 MENU STRUCTURE
MENU (LEVEL 1) (LEVEL 2) (LEVEL 3) DESCRIPTION
1 DMX Address Address DMX address
Default: 001
< 001 > < 001>
2 DMX Channel Channel
DMX Channel mode
< STD 15Ch > < HALO 1 ch >
< HALO 4 ch >
< STD 4 ch >
< STD 6 ch >
< STD 15 ch >
< EXT 16 ch >
< EXT 19 ch >
< EXT 25 ch >
3 Dimmer Mode Dimmer Mode Default: O
< O > < O > O: Dimmer speed On/O
<Dimmer1> Dim 1: Dimmer speed fast
<Dimmer2> Dim 2: Dimmer speed middle
<Dimmer3> Dim 3: Dimmer speed slow
4 White Balance White Balance
LED color calibration.
Default: RGBW=255
< OFF > < OFF >
< Manual > < R=125~255 >
< G=125~255 >
< B=125~255 >
< W=125~255 >
5 Static Fixed Color Value
Static color
Default: RGBW
< R > < RGW >
< G > < RBW >
< B > < GBW >
< W > < RGBW >
< GB > < Wht 2000K >
< RB > < Wht 3000K >
< RG > < Wht 4000K >
< RGB > < Wht 5000K >
< RW > < Wht 6000K >
< GW > <Wht 7000K >
< BW > < Wht 8000K >
Manual Color Value
Mix a custom color as static
Default: RGBW=255
< R=255 >
< G=255 >
< B=255 >
< W=255 >

ARENACOB4FC
10
6 Dynamic Patterns Pattern Speed <1-100>
Set a dynamic pattern.
Default:
Auto14 ;
speed=100;
Background=RB
Foreground=RGBW
< Pattern 01 > Background and Foreground
< Pattern 02 > <Black> < GW >
< Pattern 03 > < R > < BW >
< Pattern 04 > < G > < RGW >
< Pattern 05 > < B > < RBW >
< Pattern 06 > < W > < GBW >
< Pattern 07 > < GB > < RGBW >
< Pattern . . .> < RB > <Wht 2000K >
< Pattern 19 > < RG > < Wht 3000K >
< Pattern 20 > < RGB > < Wht 4000K >
< Pattern 21 > < RW > < Cycling >
< Pattern 22 >
< Pattern 23 >
< Random Pattern >
7 Key Lock Key Lock Default: On
Password: Up Down Up Down Enter
< ON > < ON >
< OFF >
8 Temperature LED1 xx°C
LED2 xx°C
LED3 xx°C
LED4 xx°C
9 Master/Slave < Master > Default: Slave
< Slave >
10 Back Light Back Light Default: 30 s
< On > On: background light always On
< 10 s > 10 s: O after 10 seconds
< 20 s > 20 s: O after 20 seconds
< 30 s > 30 s: O after 30 seconds
11 Mapping Rotation Mapping Rotation Invert LED order
Default: OFF
< OFF > < ON >
< OFF >
12 Information Fixture Hours <9999H>
Version <V1.0>
UID: 15D00206****
13 Reset Factory Reset Factory
Reset the xture<NO >
< YES >

11
ARENACOB4FC
3.4 DIMMER
• To enter dimmer mode and choose to simulate dierent dimming curves, press the MODE button re-
peatedly until the display shows Dimmer Mode, then press the ENTER button.
• Press the MODE button repeatedly until Dimmer Mode shows, and press ENTER button to accept.
• Use the UP/DOWN button to select a dimmer curve O - Dimmer1 - Dimmer2 - Dimmer3.
• Press ENTER button to conrm the selection.
• Press the MODE button to go back or to meet the waiting time to exit from the setup menu automati-
cally.
3.5 BACK LIGHT
• To activate backlight display press the MODE button so many times until shows Back Light, and press the
ENTER button to conrm.
• Press the UP/DOWN button to select On - 10s - 20s - 30s. Press ENTER button to conrm the selection.
• Press the MODE button to go back or to meet the waiting time to exit from the setup menu automati-
cally.
3.6 FIXTURE INFORMATION
1. Press the MODE button so many times until shows Information, and then press ENTER button.
2. Use UP/DOWN button to select: Fixture Hours - Version. - UID
3. Press ENTER button to conrm the selection.
4. Press the MODE button to go back or to meet the waiting time to exit from the setup menu automati-
cally.
Fixture Hours
This option shows the user the amount of hours the ARENACOB4FC has been in use throughout its
lifetime. Select Fixture Hours.
Version
This option shows the user the software version currently installed in the unit. Select Version.
UID
This option shows the RDM identication number (see paragraph 3.23)
3.7 WHITE BALANCE
Enter the White balance to adjust the Red,Green,and Blue parameter to make dierent whites.
• Press the MODE button so many times until shows White Balance, and press the ENTER button to conrm.
• Select the color R, G, B, W through the UP/DOWN buttons, then press the ENTER button.
• Using UP/DOWN button, select the desired color value 125 - 255.
• Press ENTER button to continue to the next color R, G, B, W.
• Continue until the desired mix is obtained.
• Press the MODE button to go back or to meet the waiting time to exit the setup menu.

ARENACOB4FC
12
3.8 KEY LOCK
Enter the Key Lock mode to select whether the access password is on or o.
• Press the MODE button so many times until show Key Lock and press the ENTER button to conrm.
• Use UP/DOWN button to select: ON or OFF.
• Press ENTER button to conrm the selection.
When the xture is set as pass ON, after 30 seconds or turn on the xture next time, the xture will need
an access password to enter the display menu control.
NOTE - The factory access password is UP + DOWN + UP + DOWN (press ENTER to conrm the access).
3.9 AUTO SHOW
If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-
gramme provided that the blackout mode is switched o:
• Press the MENU button so many times until the display shows Auto Show, then press the ENTER button.
• Press the UP/DOWN button to switch between the preprogrammed Dynamic Patterns. The unit will
operate in show mode.
• Choose the foreground and background color, then press ENTER.
• Use the UP/DOWN button to select the desired run speed slow-fast 1-100.
• Press the ENTER button to save the setting.
IMPORTANT: Dynamic patterns are fully pre-programmed and will not be altered by changes.
3.10 STATIC MODE
This xture has the ability to accept custom static color settings. Access these chases via the control panel
on the back of the xture.
• Press the MENU button so many times until the display shows Static, then press the ENTER button.
• Select Fixed Color through the UP/DOWN buttons, then press ENTER.
• Set the colors R , G , B, W, GB, RB, [...] through the UP/DOWN buttons, then press ENTER.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.11 MANUAL MODE
This mode allows to combine the colors red, green, blue and white (R, G, B, W).
• Press the MENU button so many times until the display shows Static, then press ENTER.
• Select Manual Color through the UP/DOWN buttons, then press ENTER.
• Select the color R, G, B, W through the UP/DOWN buttons, then press ENTER.
• Using UP/DOWN buttons, select the desired color value 000 - 255.
• Press ENTER button to continue to the next color R, G, B,W.
• Continue until the desired mix is obtained.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu
3.12 MODALITÀ MASTER/SLAVE
This mode allows you to link up multiple units ARENACOB4FC online without a controller. The rst unit
will be set as the master and the others function as slaves with the same eect.
• Press the MODE button so many times until the display shows [Master/Slave].
• Press the ENTER button to conrm.
• Press the UP/DOWN button and select [Slave] to set the drive as a slave.
• Press the UP/DOWN button and select [Master] to set the drive as a master.
• Press the ENTER button for save the setting.

13
ARENACOB4FC
3.13 LINKING
• 1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.
• 2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
3.14 DMX MODE
• Press the MENU button so many times until show Dmx Channel and press ENTER to conrm.
• Press the UP/DOWN button to select the desired DMX mod.
• Press ENTER button to store.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu
3.15 DMX ADDRESSING
• Press the MENU button so many times until show Dmx Address and press ENTER to conrm.
• Press the UP/DOWN button to select the desired DMX address 001 - 512. Press and hold to scroll quickly.
• Press ENTER button to store.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu
3.16 RDM - Remote Device Management
With this function you can call up various submenus via RDM.
This device is RDM ready. RDM stands for “Remote Device Management” and makes remote control of
devices connected to the DMX-bus possible. Manual settings like adjusting the DMX starting address are
no longer needed. This is especially useful when the device is installed in a remote area. RDM is integrated
in DMX without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1
and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated
in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not inuence
conventional devices. If DMX splitters are used and RDM control is to be used, these splitters must sup-
port RDM. The number and type of RDM parameters depend on the RDM controller (not included) is used.

ARENACOB4FC
14
3.17 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
cause faulty xture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
• Connect the controller DMX input to the DMX output of the rst unit.
• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
• When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.18 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in gure.
Fig.5
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
Fig.6
Example:
3 pin XLR connector

15
ARENACOB4FC
3.19 DMX CONTROL
HALO 1ch
MODE FUNCTION DMX
Value
1 Ch
1DIMMER
0~100% 000 - 255
HALO 4ch
MODE FUNCTION DMX
Value
4 Ch
1PIXEL 1
Dimmer 0~100% 000 - 255
2PIXEL 2
Dimmer 0~100% 000 - 255
3PIXEL 3
Dimmer 0~100% 000 - 255
4PIXEL 14
Dimmer 0~100% 000 - 255
STANDARD - STD 4ch
MODE FUNCTION DMX
Value
STD 4 Ch
1RED
0~100% 000 - 255
2GREEN
0~100% 000 - 255
3BLUE
0~100% 000 - 255
4WHITE
0~100% 000 - 255
STANDARD - STD 6ch
MODE FUNCTION DMX
Value
STD 6 Ch
1DIMMER
0~100% 000 - 255
2RED
0~100% 000 - 255
3GREEN
0~100% 000 - 255
4BLUE
0~100% 000 - 255
5WHITE
0~100% 000 - 255
6
STROBE
No function
Strobe Slow to Fast
No function
Random strobe Slow to Fast
No function
000 - 030
031 - 100
101 - 130
131 - 200
201 - 255
In HALO mode, the xture emulates dimmer curve
and color as an halogen DWE.
1234
Mapping rotation: OFF

ARENACOB4FC
16
STANDARD - STD 15ch
MODE FUNCTION DMX
Value
STD15Ch
1DIMMER - 0~100% 000 - 255
2RED - 0~100% 000 - 255
3GREEN - 0~100% 000 - 255
4BLUE - 0~100% 000 - 255
5WHITE - 0~100% 000 - 255
6
STROBE
No function
Strobe Slow to Fast
No function
Random strobe Slow to Fast
No function
000 - 030
031 - 100
101 - 130
131 - 200
201 - 255
7
COLOR FUNCTION
No Function
CTC Function
Forward Spin
Reverse Spin
Color Presets
HALO DWE
TBD
000 - 010
011 - 039
040 - 059
060 - 079
080 - 099
100 - 119
120 - 255
8
CTC Function (fade change)
2000K~3000K
3000K~4000K
4000K~5600K
5600K~8000K
8000K
Forward Spin
Rainbow Eect - Slow to Fast
Reverse Spin
Rainbow Eect - Slow to Fast
Color Preset (fade change)
R 100% G 0~100% B 0%
R 100%~0% G 100% B 0%
R 0% G 100% B 0~100%
R 0% G 100%~0% B 100%
R 0%~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B 0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100% W 100%
Halo DWE
Dimmer 0~100%
000 - 223
224 - 231
232 - 239
240 - 247
248 - 255
000 - 255
000 - 255
000 - 028
029 - 056
057 - 084
084 - 112
113 - 140
141 - 168
169 - 196
197 - 224
225 - 255
000 - 255
9
DYNAMIC PATTERNS
No Function
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Pattern 6
Pattern 7
Pattern 8
Pattern 9
Pattern 10
Pattern 11
Pattern 12
Pattern 13
Pattern 14
Pattern 15
Pattern 16
Pattern 17
Pattern 18
Pattern 19
Pattern 20
Pattern 21
Pattern 22
Pattern 23
Random Pattern
000 - 010
011 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 255
10
PATTERNS SPEED
Static indexing
Speed slow to fast
TBD / Not used
000 - 029
030 - 140
141 - 255
11
FOREGOUND COLOR
No function (COLOR FUNCTION CHANNEL)
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
000 - 012
013 - 025
026 - 038
039 - 051
052 - 064
065 - 077
078 - 090
091 - 103
104 - 116
117 - 129
130 - 142
143 - 155
156 - 168
169 - 181
182 - 194
195 - 207

17
ARENACOB4FC
11
White 2000K
White 3000K
White 4000K
Color Cycling
208 - 220
221 - 233
234 - 246
247 - 255
12 FOREGROUND DIMMER
0~100% 000 - 255
13
BACKGROUND COLOR
No function (main RGBW channels control)
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
White 2000K
White 3000K
White 4000K
Color Cycling
000 - 012
013 - 025
026 - 038
039 - 051
052 - 064
065 - 077
078 - 090
091 - 103
104 - 116
117 - 129
130 - 142
143 - 155
156 - 168
169 - 181
182 - 194
195 - 207
208 - 220
221 - 233
234 - 246
247 - 255
14 BACKGROUND DIMMER
Dimmer 0~100% 000 - 255
15
DIMMER FADE
Preset dimmer speed from display menu
Dimmer curve Fast to Slow
000 - 000
001 - 255
EXTENDED - EXT 16ch
MODE FUNCTION DMX
Value
EXT 16 Ch
1
PIXEL1
0~100% RED 000 - 255
2 0~100% GREEN 000 - 255
3 0~100% BLUE 000 - 255
4 0~100% WHITE 000 - 255
5
PIXEL2
0~100% RED 000 - 255
6 0~100% GREEN 000 - 255
7 0~100% BLUE 000 - 255
8 0~100% WHITE 000 - 255
9
PIXEL3
0~100% RED 000 - 255
10 0~100% GREEN 000 - 255
11 0~100% BLUE 000 - 255
12 0~100% WHITE 000 - 255
13
PIXEL4
0~100% RED 000 - 255
14 0~100% GREEN 000 - 255
15 0~100% BLUE 000 - 255
16 0~100% WHITE 000 - 255

ARENACOB4FC
18
EXTENDED - EXT 21ch
MODE FUNCTION DMX
Value
EXT 21 Ch
1
PIXEL1
0~100% RED 000 - 255
2 0~100% GREEN 000 - 255
3 0~100% BLUE 000 - 255
4 0~100% WHITE 000 - 255
5
PIXEL2
0~100% RED 000 - 255
6 0~100% GREEN 000 - 255
7 0~100% BLUE 000 - 255
8 0~100% WHITE 000 - 255
9
PIXEL3
0~100% RED 000 - 255
10 0~100% GREEN 000 - 255
11 0~100% BLUE 000 - 255
12 0~100% WHITE 000 - 255
13
PIXEL4
0~100% RED 000 - 255
14 0~100% GREEN 000 - 255
15 0~100% BLUE 000 - 255
16 0~100% WHITE 000 - 255
17 DIMMER
0~100% 000 - 255
18
STROBE
No function
Strobe Slow to Fast
No function
Random strobe Slow to Fast
No function
000 - 030
031 - 100
101 - 130
131 - 200
201 - 255
19
COLOR FUNCTION
No Function
CTC Function
Forward Spin
Reverse Spin
Color Presets
HALO DWE
TBD
000 - 010
011 - 039
040 - 059
060 - 079
080 - 099
100 - 119
120 - 255
20
CTC Function (fade change)
2000K~3000K
3000K~4000K
4000K~5600K
5600K~8000K
8000K
Forward Spin
Rainbow Eect - Slow to Fast
Reverse Spin
Rainbow Eect - Slow to Fast
000 - 223
224 - 231
232 - 239
240 - 247
248 - 255
000 - 255
000 - 255
EXTENDED - EXT 27ch
MODE FUNCTION DMX
Value
EXT 27 Ch
1
PIXEL1
0~100% RED 000 - 255
2 0~100% GREEN 000 - 255
3 0~100% BLUE 000 - 255
4 0~100% WHITE 000 - 255
5
PIXEL2
0~100% RED 000 - 255
6 0~100% GREEN 000 - 255
7 0~100% BLUE 000 - 255
8 0~100% WHITE 000 - 255
9
PIXEL3
0~100% RED 000 - 255
10 0~100% GREEN 000 - 255
11 0~100% BLUE 000 - 255
12 0~100% WHITE 000 - 255
13
PIXEL4
0~100% RED 000 - 255
14 0~100% GREEN 000 - 255
15 0~100% BLUE 000 - 255
16 0~100% WHITE 000 - 255
17
COLOR FUNCTION
No Function
CTC Function
Forward Spin
Reverse Spin
Color Presets
HALO DWE
TBD
000 - 010
011 - 039
040 - 059
060 - 079
080 - 099
100 - 119
120 - 255
20
Color Preset (fade change)
R 100% G 0~100% B 0%
R 100%~0% G 100% B 0%
R 0% G 100% B 0~100%
R 0% G 100%~0% B 100%
R 0%~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B 0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100% W 100%
Halo DWE
Dimmer 0~100%
000 - 028
029 - 056
057 - 084
084 - 112
113 - 140
141 - 168
169 - 196
197 - 224
225 - 255
000 - 255
21
DIMMER FADE
Preset dimmer speed from display menu
Dimmer curve Fast to Slow
000 - 000
001 - 255

19
ARENACOB4FC
20
PATTERNS SPEED
Static indexing
Speed slow to fast
TBD / Not used
000 - 029
030 - 140
141 - 255
21
FOREGOUND COLOR
No function (main RGBW channels control)
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
White 2000K
White 3000K
White 4000K
Color Cycling
000 - 012
013 - 025
026 - 038
039 - 051
052 - 064
065 - 077
078 - 090
091 - 103
104 - 116
117 - 129
130 - 142
143 - 155
156 - 168
169 - 181
182 - 194
195 - 207
208 - 220
221 - 233
234 - 246
247 - 255
22 FOREGROUND DIMMER 0~100% 000 - 255
23
BACKGROUND COLOR
No function (main RGBW channels control)
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
White 2000K
White 3000K
White 4000K
Color Cycling
000 - 012
013 - 025
026 - 038
039 - 051
052 - 064
065 - 077
078 - 090
091 - 103
104 - 116
117 - 129
130 - 142
143 - 155
156 - 168
169 - 181
182 - 194
195 - 207
208 - 220
221 - 233
234 - 246
247 - 255
24 BACKGROUND DIMMER 0~100% 000 - 255
18
CTC Function (fade change)
2000K~3000K
3000K~4000K
4000K~5600K
5600K~8000K
8000K
Forward Spin
Rainbow Eect - Slow to Fast
Reverse Spin
Rainbow Eect - Slow to Fast
Color Preset (fade change)
R 100% G 0~100% B 0%
R 100%~0% G 100% B 0%
R 0% G 100% B 0~100%
R 0% G 100%~0% B 100%
R 0%~100% G 0% B 100%
R 100% G 0% B 100%~0%
R 100% G 0%~100% B 0%~100%
R 100%~0% G 100%~0% B 100%
R 100% G 100% B 100% W 100%
Halo DWE
Dimmer 0~100%
000 - 223
224 - 231
232 - 239
240 - 247
248 - 255
000 - 255
000 - 255
000 - 028
029 - 056
057 - 084
084 - 112
113 - 140
141 - 168
169 - 196
197 - 224
225 - 255
000 - 255
19
DYNAMIC PATTERNS
No Function
Pattern 1
Pattern 2
Pattern 3
Pattern 4
Pattern 5
Pattern 6
Pattern 7
Pattern 8
Pattern 9
Pattern 10
Pattern 11
Pattern 12
Pattern 13
Pattern 14
Pattern 15
Pattern 16
Pattern 17
Pattern 18
Pattern 19
Pattern 20
Pattern 21
Pattern 22
Pattern 23
Random FX
000 - 010
011 - 020
021 - 030
031 - 040
041 - 050
051 - 060
061 - 070
071 - 080
081 - 090
091 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 255