thomann Stairville DJ Lase 40-G MK-III User manual

DJ Lase 40-G MK-III
showlaser
user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
17.09.2019, ID: 276238 (V4)

Table of contents
1 General information................................................................................................................................. 5
1.1 Further information........................................................................................................................... 6
1.2 Notational conventions.................................................................................................................... 7
1.3 Symbols and signal words............................................................................................................... 7
2 Safety instructions.................................................................................................................................. 10
3 Features....................................................................................................................................................... 19
4 Installation.................................................................................................................................................. 20
5 Starting up.................................................................................................................................................. 27
6 Connections and controls................................................................................................................... 30
7 Operating.................................................................................................................................................... 38
7.1 Starting and stopping the device............................................................................................... 38
7.2 Main menu.......................................................................................................................................... 40
7.3 Menu overview................................................................................................................................. 44
7.4 Functions in ‘DMX’ mode.............................................................................................................. 45
7.5 Pattern list........................................................................................................................................... 48
Table of contents
DJ Lase 40-G MK-III
3

8 Technical specications....................................................................................................................... 51
9 Plug and connection assignments.................................................................................................. 53
10 Troubleshooting...................................................................................................................................... 54
11 Cleaning....................................................................................................................................................... 57
12 Protecting the environment.............................................................................................................. 58
Table of contents
showlaser
4

1 General information
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐
fore reserve the right to make changes without notice. Please refer to the latest version of the
user manual which is ready for download under www.thomann.de.
General information
DJ Lase 40-G MK-III
5

1.1 Further information
On our website (www.thomann.de) you will nd lots of further information and details on the
following points:
Download This manual is also available as PDF le for you to download.
Keyword search Use the search function in the electronic version to nd the topics of
interest for you quickly.
Online guides Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the customer service will
gladly assist you.
General information
showlaser
6

1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’ .
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Letterings
Displays
General information
DJ Lase 40-G MK-III
7

Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
WARNING! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in death or serious
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
Warning – laser radiation.
General information
showlaser
8

Warning signs Type of danger
Warning – dangerous optical radiation.
Warning – suspended load.
Warning – danger zone.
General information
DJ Lase 40-G MK-III
9

2 Safety instructions
This device is intended to be used for the projection of laser light eects. It has been designed
exclusively for show applications. Use the device only as described in this user manual. Any
other use or use under other operating conditions is considered to be improper and may result
in personal injury or property damage. No liability will be assumed for damages resulting from
improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Intended use
Safety instructions
showlaser
10

Laser safety requirements are based on DIN EN 60825-1:2015. The corresponding accident pre‐
vention regulation of the Accident Prevention and Insurance Association in Germany is BGV-
B2.
This device contains a class-3B laser. It comes equipped with a safety key and a jack for con‐
necting an external safety switch. Always remove the key when the device is not attended by a
trained operator.
As an operator you are responsible for the safety of all persons present. Familiarize yourself
with the laser safety regulations that apply in your country. To ensure safe operation, it is
important to pay attention to the following instructions.
Prior to commissioning, the company/operator must appoint a qualied person as laser pro‐
tection ocer in writing and notify the operation of the laser equipment to the Accident Pre‐
vention and Insurance Association and to the authority responsible for occupational safety. In
the event of public use, the complete laser equipment must be approved by an expert prior to
commissioning.
Laser safety basics
Safety instructions
DJ Lase 40-G MK-III
11

DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
Safety
Safety instructions
showlaser
12

DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers.
There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are missing or
damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a pro‐
tective contact plug. Do not modify the mains cable or the plug. Failure to do so
could result in electric shock/death or re. If in doubt, seek advice from a regis‐
tered electrician.
Safety instructions
DJ Lase 40-G MK-III
13

DANGER!
Laser radiation – avoid exposure to beam
The device contains a class-3B laser, classied according to EN 60825-1:2015. Do
not look into the laser beam. The laser beam can injure your eyes when you
directly look into it. Do not expose yourself to the laser beam. The laser beam can
cause skin burns.
In this context take extreme care when using converging optical instruments.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
Safety instructions
showlaser
14

WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons
should avoid looking at strobe lights.
NOTICE!
Laser radiation – risk of re
Keep the area exposed to laser radiation free from ammable substances.
NOTICE!
Risk of re
Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked ames.
Safety instructions
DJ Lase 40-G MK-III
15

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
Only operate the device within the ambient conditions specied in the chapter
‘Technical specications’ of this user manual. Avoid heavy temperature uctua‐
tions and do not switch the device on immediately after it was exposed to tem‐
perature uctuations (for example after transport at low outside temperatures).
Dust and dirt inside can damage the unit. When operated in harmful ambient
conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by
qualied service personnel at regular intervals to prevent overheating and other
malfunction.
Safety instructions
showlaser
16

NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
NOTICE!
Possible damage due to installation of a wrong fuse
The use of dierent types of fuses can cause serious damage to the unit. Fire
hazard!
Only fuses of the same type may be used.
Safety instructions
DJ Lase 40-G MK-III
17

NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react
with the coating of your parquet, linoleum, laminate or PVC oor and after some
time cause permanent dark stains.
In case of doubt, do not put the rubber feet directly on the oor, but use felt-pad
oor protectors or a carpet.
Safety instructions
showlaser
18

3 Features
This showlaser is specially suited for discos, clubs, bars, small stages, etc. and can be easily inte‐
grated in the light show or operated in ‘stand alone’ mode.
Special features of this device:
nControl via DMX (8 channels), via infrared remote control and via buttons and display on
the unit
nPreprogrammed automatic shows
nSound control
nMaster / slave mode
n32 dierent patterns
nLaser diode: green (40 mW)
Features
DJ Lase 40-G MK-III
19

4 Installation
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
You can install the device standing or hanging. When in use, the device must be mounted at a
solid surface or clamped to an approved truss.
Work from a stable platform whenever you install or move the device or when you perform
any kind of maintenance. Block access under the work area.
Installation
showlaser
20