Protocol SAW46 User manual

-
-ODD-
42581
SAW46
46" / 1000 LB CAPACITY
LIGHTWEIGHT ALUMINUM
ADJUSTABLE LEG SAWHORSE
PRODUCT MANUAL
SCAN TO WATCH PRODUCT
ASSEMBLY VIDEO
CAUTION: To reduce the risk of injury, user must read and understand
this product manual. Save these instructions for future reference.
PROTOCOLEQUIPMENT.COM

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
TABLE OF CONTENTS
Features and Specifications......................................................................................................................3
Preparing the Sawhorse..........................................................................................................................4-5
Adjusting Height of the Sawhorse...........................................................................................................6
Mounting Workpiece or Sacrificial Wood.............................................................................................. 7
Constructing a Jobsite Table..................................................................................................................... 8
Storing the Sawhorse.............................................................................................................................9-10
Safety and Warnings.....................................................................................................................................11
General Maintenance....................................................................................................................................11
Warranty ............................................................................................................................................................11
WARNING: Be sure to read and understand all safety instructions in this manual, including all
safety alert symbols such as “DANGER”, “WARNING”, “CAUTION”, and “IMPORTANT” before using
this product. Failure to follow all instructions listed in the manual may result in electric shock,
fire and/or serious personal injury.
FEATURES AND SPECIFICATIONS
46"
6
1 3 2
23" - 30"
5
4
18.5" - 24"
SPECIFICATIONS INCLUDED FEATURES
HEIGHT 23" - 30" 1 2" X 4" Support arms
WIDTH 46" 2 Saddle trays
DEPTH 18.5" - 24" 3 Multipurpose straps
MAX WEIGHT CAPACITY 1000 lb. 4 Fold out material support brackets
MATERIAL Aluminum, Steel, Nylon 5 Height adjustable legs with non-marring feet
PRODUCT WEIGHT 19.4 lb. 6 Built-in stacking tabs
3

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
PREPARING THE SAWHORSE
PUSH TO SLIDE
1. Place sawhorse on a flat and level surface with folded legs facing up.
2. Push to slide leg lock and unfold first set of legs from chassis.
3. Deploy first set of legs. Make sure cross brace is secured in place to ensure legs are
fully opened.
4. Unfold second set of legs and follow step #3.
4

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
i
f
ii
ii
ti
t)
-□□□-
•
•
i,
i,
i,
i
o
=
PREPARING THE SAWHORSE
5. After both sets of legs are deployed, lift sawhorse in an upright position.
6. Ensure sawhorse is stable and both sets of legs are fully opened.
5

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
ADJUSTING HEIGHT OF THE SAWHORSE
NOTE: Legs adjust independently in 1" increments.
EXTEND LEGS: Pull legs down to desired height.
PUSH TO
RELEASE
RETRACT LEGS: Press height adjustment button and slide legs down to desired height.
6

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
MOUNTING WORKPIECE OR SACRIFICIAL WOOD
1. Place workpiece or 2" X 4" lumber on top of chassis.
2. Rubber straps are located on both ends of sawhorse. Pull each strap over material and
secure strap to knob.
PRE-DRILLED
MOUNTING HOLES
NOTE: Pre-drilled mounting holes on saddle trays can also be used to attach sacrificial wood.
7

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
CONSTRUCTING A JOBSITE TABLE
Materials Required: (2) SAW46, (4) 2" X 4" Lumber, (1) Plywood sheet
1. Place 2" X 4" lumber on top of each chassis.
2. Rubber straps are located on both ends of sawhorses. Pull each strap over material and
secure strap to knob.
3. Place 2" X 4" lumber in support arms to connect sawhorse units.
4. Place sheet on top of sawhorses to create a workspace.
8

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
STORING THE SAWHORSE
PUSH TO
RELEASE
1. If legs are extended, press height adjustment button and slide legs down until fully retracted.
2. Carefully flip sawhorse over so that legs are facing up.
9

FIND OUT MORE AT PROTOCOLEQUIPMENT.COM
STORING THE SAWHORSE
FIRST SET OF
LEGS NEST INTO
CHASSIS FRAME,
OPPOSITE SIDE OF
LEG LOCK
LEG LOCK
3. Set of legs opposite from leg lock must be folded into chassis first.
4. Press on cross brace to bring legs together. Push legs down until fully nested into chassis
frame, opposite side of leg lock.
5. Repeat Step #4 to fold second set of legs. Push legs downs until fully nested into chassis
frame, same side as leg lock.
6. Slide leg lock to secure legs in place for transport and storage.
10