Proxima 5600 User manual

USER'S GUIDE
PROXIMA
Desktop
Projector
5600

INFORMATION TO THE USER
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the user's
guide, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
TO THE OWNER
As the owner of a Desktop Projector 5600, you are probably eager to try out your new projector. Before you do,
we suggest that you spend a little time reading this guide to familiarize yourself with the operating procedures,
so that you will receive maximum satisfaction from the many features included on your new projector. l
This user's guide will acquaint you with your projector’s features. Reading it will help us too. Through the years,
we have found that many service requests were not caused by problems with our projectors. They were caused
by problems that could have been prevented, if the owner had followed the instructions in the guide.
You can often correct operating problems yourself. If your projector fails to work properly, see
"TROUBLESHOOTING" section on pages 42 ~ 43 and try the solutions marked for each problem.
SAFETY PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit
into the power outlet. Do not try to defeat this safety feature.
intense light source. Do not stare directly into the projection lens as possible eye damage could result.
Be especially careful that children do not stare directly into the beam.
If Projector will not be used for an extended time, unplug the Projector from the power outlet.
READ AND KEEP THIS USER'S GUIDE FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
— BACK). NO USER-SERVICEABLE | PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL |
THIS SYMBOL INDICATES THAT DANGER- - THIS SYMBOL INDICATES THAT THERE ARE
OUS VOLTAGE CONSTITUTING A RISK OF IMPORTANT OPERATING AND MAINTENANCE
ELECIHIC SHOCK IS PRESENT WITHIN INSTRUCTIONS IN THE USER'S GUIDE WITH
THIS UNIT. THIS UNIT.

IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read
before the product is operated.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Use
only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturers instructions,
and should use a mounting kit approved by the
manufacturer.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool , etc...
Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of
the equipment and to protect it from overheating.
The openings should never be covered with cloth or other
material, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or
over a radiator or heat register.
This projector should not be placed in a built-in installation
such as a bookcase unless proper ventilation is provided.
This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord may be damaged by persons walking on it.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
e. If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks
to determine that the projector is in safe operating
condition.
This projector is equipped with a grounding type AC line
plug. Should you be unable to insert the plug into the
outlet, contact your electrician. Do not defeat the safety
purpose of this grounding type plug.
Follow all warnings and instructions marked on the
projectors.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and powerline surges.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector,
and can also be dangerous.
PROJECTOR PROJECTOR
(FRONT)
(SIDE)
WALL

TABLE OF CONTENTS
PAGE
INTRODUCTION
«HH
e
He
e
hm
ee
hh
SEESE
EENNO
e
ne
eir
ese
rns
s
rrr
e
rn
e
ne
e
nennen
5
POWER
REQUIREMENT
«ee
III
He
ehh
eh
nh
a
eniti
tee
re
e
eee
re
e
eene
6
DESCRIPTION
HH
He
He
hene
nnne
hes
a
he
ete
e
ise
e
ei
e
ei
ese
rie
rne
ne
en
7
SETTING-UP
THE
PROJECTOR
+
e
mee
he
e
hne
hene
ten
nene
rene
eser
e
nene
8-9
MOVING
THE
PROJECTOR:
ee
eee
e
es
i
hne
n
rhe
a
rh
e
e
nen
e
e
e
nenne
enn
9
CONNECTING
THE
PROJECTOR
e
I
me
eI
ene
hene
he
ee
hee ree
re
e
enun
10-17
OPERATION
OF
CONTROLS:
I
e
e
ehe
hne
anh
nen
n
ee
i
e
e
i
erre
e
neris
18-19
OPERATION
OF
REMOTE
CONTROL
«eH
Ihm
hene
he
ee
ee
ne
e
e
er
eser
renun
20-21
CONTROL
THE
PROJECTOR
«ee
He
ee
ee
he
enr
eee
hne
e
e
re
e
enner
rrearen
22-23
USING
THE
PROJECTOR
eH
e
e
hee
he
i
hne
hene
e
e
ree
ree
re
ee
serene
is
24-25
COMPUTER
SYSTEM
SELECT
(COMPUTER
MODE)
eee
eene
26-27
PICTURE
IMAGE
ADJUSTMENT
(COMPUTER
MODE):
Hee
eme
28-29
PICTURE
SCREEN
ADJUSTMENT
(COMPUTER
MODE)
eH
ee
mee
30
COLOR
SYSTEM
SELECT
(VIDEO
MODE)
eH
eee
ene
«1
PICTURE
IMAGE
ADJUSTMENT
(VIDEO
MODE):
eH
eee
ene
32-33
PICTURE
SCREEN
ADJUSTMENT
(VIDEO
MODE)
Hee
Hee
eene
34
OTHER
FUNCTION
SETTING
«e
II
RH
eme
ee
n
ee
hh
e
err
es
rs
rr
ss
aan
35-36
PC
ADJUSTMENT
RRRSEEPEEEEEENMMMMMMNMMM
37-38
LANGUAGE
ADJUSTMENT
e
mH
mee
hene
hee
rese
he
er
e
hte
n
esa
DEE
na
ss
39
AIR
FILTER
CARE
AND
CLEANING
eH
ee
rr
ana
Po
rr
er
IEP
Ea
En
regnis
40
TEMPERATURE
WARNING
INDICATOR
«e
eee
eee
eene
40
LAMP
REPLACEMENT
:
HH
he
e
enne
hne
ene
re
eri
e
sse
hse
resa
nra
ssa
es
41
CLEANING
THE
LENS
e
I
ene
eh
e
hee
he
e
ee
e
e
eres
s
ris
nauenean.
42
TROUBLESHOOTING:
IH
hene
ene
hee nna
ee
eer
ee
hse
sans
a
ese
anane
42-43
TECHNICAL
SPECIFICATIONS
Hee
me
hehe
ehhe
e
rhese
rre
resale
rs
44

INTRODUCTION
The desktop projector 5600 is a multimedia projector designed for portability, durability, and ease of use. The desktop
projector 5600 utilizes built-in multimedia features, a palette of 16.8 million colors, and active matrix liquid crystal display
(LCD) technology.
COMPATIBILITY
The projector is compatible with many different types of personal computers and video devices, including;
è |BM-compatible computers, including laptops, up to 1024 X 768 resolution with a vertical frequency up to 75Hz.
€ Apple Macintosh and PowerBook computers up to 1024 x 768 resolution.
e Various VCRs, video disc players, video cameras, satellite TV tuners or other AV equipment using any of the worldwide
video standards, including NTSC, NTSC4.43, PAL and SECAM.
IMAGE RESOLUTION
The resolution of the projector's projected image is 832 x 624. The projector displays computer images just as they
appear on your computer's monitor. Screen resolutions between 832 X 624 and 1024 x 768 are compressed to 800 x
600. The projector cannot display screen resolutions above 1024 X 768. If your computer's screen resolution is higher
than 1024 x 768, reset it to a lower resolution before you connect the projector.
PORTABILITY
The projector is extremely compact in size and weight. Having a sophisticated shape like an attaché case with a
retractable carrying handle, the projector will help you make powerful presentations wherever you go. To strengthen the
portability, the LENS RETRACT function is designed to protect the lens from being damaged during transportation. With
this function, the lens is pulled in when not in use.
UNPACKING THE PROJECTOR
The projector comes with the parts shown listed below. Check to make sure all are included. If any parts are missing,
contact an authorized dealer or service station.
* User's Guide.
@ AC Power Cord.
@ Remote Control Transmitter Unit and batteries.
@ Lens Cover.
€ Protective Dust Cover.
€ VGA Cable.
e VGA/MAC Adapter.
e Mouse Cable for PS/2 port.
@ Mouse Cable for serial port.
@ Mouse Cable for ADB port.
TRADEMARKS
€ Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.
€ IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

POWER
REQUIREMENTS
Your
projector
uses
nominal
input
voltages
of
100-120
VAC
or
200-240
VAC.
The
projector
automatically
selects
the
correct
input
voltage.
The
projector
is
designed
to
work
with
single-phase
power
systems
having
a
grounded
neutral
conductor.
To
reduce
the
risk
of
electrical
shock,
do
not
plug
into
any
other
type
of
power
system.
Consult
your
authorized
dealer
or
service
station
if
you
are
not
sure
what
type
of
power
is
supplied
to
your
building.
Projector side (Female)
Sg
|
OE
GUARD
Connect the AC power
supply cord (supplied) to
the projector.
Slide the guard when the AC cord may
not be connected by the guard.
AC outlet side (Male)
CIO

DESCRIPTION
INFRARED
REMOTE
RECEIVER
PROJECTION LENS
REMOVABLE
LENS COVER
EXHAUST VENT
INFRARED
A
REMOTE
MAIN
ON/OFF
RECEIVER
CAUTION
HOT
AIR
!
SWITCH
Air blown from the exhaust vent is hot.
Observe the following when handling your
projector or choosing a location to install it.
e Keep heat-sensitive objects away from the
exhaust port.
e |f you set the projector on top of a metallic
surface, the surface will become hot because
of the hot air exhaust. Be careful when
handling.
e Do not touch the cabinet near to the exhaust
vent, and especially screws and metallic parts.
These parts will become hot while the projector
is used.
CARRY HANDLE
POWER CORD
CONNECTOR
BOTTOM
EH
HL
LAMP
COVER
LEVELING/ELEVATING ARNT
VENT

SETTING-UP THE PROJECTOR
POSITIONING: * This projector is basically designed to project on a flat projection surface.
€ This projector can be focused from 3.6’ (1.1m) ~ 75.6' (23.0m).
* Use the illustration below as an example when positioning the projector to the screen.
Maximum Zoom
ROOM LIGHT
Ideally the projector should be placed in a Minimum Zoom
room with limited light. Picture quality will be
directly affected by lighting conditions.
H1
DISTANCE
VENTILATION
Although this projector has a cooling fan to protect it from
overheating, please be careful to set the projector so that it can cool
properly and you can avoid a risk of fire and malfunction.
e Keep the side grill at least 3.3’ (1m) away from any
object.
e Make sure that there are no objects under the projector.
An object under the projector may prevent the projector
from taking the cooling air through the bottom vent.
| e Do not cover the vents with papers or other materials.
EXHAUST VENT
AIR INTAKE VENT
(BOTTOM SIDE)

Picture
adjustments
can
be
made
with
the
two
leveling/elevating
feet.
Adjustments
of
up
to
6
^
are
possible
by
rotating
the
feet
on
the
bottom
of
the
projector.
Level
the
projector,
by
rotating
the
two
feet
(left
and
right)
on
the
bottom
of
the
projector.
LEVELING/ELEVATION
FEET
|
MOVING
THE
PROJECTOR
Use
the
carry
handle
when
moving
the
projector.
Replace
the
lens
cover
when
moving
the
projector
to
prevent
damage
to
the
lens.

| CONNECTING THE PROJECTOR
Your
projector
is
equipped
with
various
audio/video
inputs
and
outputs
including
Computer
HDB15-pin
(VGA)
terminals,
Monitor HDB15-pin
(VGA)
terminals
and
S-VHS
video
.
CONNECTING THE COMPUTER
CONNECTING TO THE COMPUTER INPUT HDB15-PIN (VGA) TERMINAL
Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.
€ Connect the computer to this terminal using the VGA cable and VGA/MAC adapter (provided).
WARNING: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference)
emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any
other cable.
CONNECTING TO THE MONITOR OUTPUT HDB15-PIN (VGA) TERMINAL
Monitor can be connected to the HDB15-pin (VGA) terminal on the projector.
@ Connect the monitor to this terminal using the monitor
; Pin No./Signal Pin No./Signal
cable (not provided). : 1 Red input 9 Non Connect
2 Green input 10 Ground (Vert. sync.)
HDB15-PIN 3 Blue input 11 Sense 0
TERMINAL 4 Sense2 12 Sense 1
5 Ground (Horiz. sync.) 13 Horiz. sync.
6 Ground (Red) 14 Vert. sync.
7 Ground (Green) 15 Reserved
8 Ground (Blue)
CONNECTING TO THE COMPUTER AUDIO INPUT JACKS
* Connect audio outputs from your computer to these jacks using the audio cable (not provided).
e If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right
and left jacks.
e If the audio input of the audio equipment is monaural, connect it to the left jack.
CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTOR
€ if you wish to control the computer by the projector's remote control unit, you must connect a cable (three type cables
provided) from contro! port (PS/2, Serial or ADB port) on your computer to this connector.
g PS/2 Port ADB Port
E [—— w ——]
[2| CK |——— | ADB |
E CONTROL PORT
—10—

Connecting
an
IBM-compatible
desktop
computer
COMPUTER
COMPUTER
OUTPUT VGA CABLE
(PROVIDED)
MONITOR CABLE
(NOT PROVIDED)
AUDIO
SERIAL
PORT
PS/2
OUTPUT
INPUT
PORT
INPUT
COMPUTER
INPUT
ONITOR
UTPUT
oz
MOUSE CABLE
FOR PS/2 PORT
(PROVIDED)
CONTROL PORT
OUTPUT
oNoIDEO VIDEO (BNC) S-VIDEO
i
(e)
00
Se
[jaucio[r] ,, VIDEO
94000) EXT. SP (8 Q)
MOUSE CABLE
FOR SERIAL PORT
(PROVIDED)
AUDIO CABLE
(NOT
PROVIDED)
COMPUTER
AUDIO INPUT
NOTE:
The
hook
up
should
be
done
as
per
the
above
illustration.
After
hook
up,
turn
on
the
projector,
monitor,
computer,
in
that
order.
p=

Connecting a Macintosh desktop computer
COMPUTER
MONITOR CABLE
(NOT PROVIDED)
COMPUTER
OUTPUT
VGA CABLE
m (PROVIDED)
VGA/MAC ADAPTER
(PROVIDED)
AUDIO ADB
OUTPUT PORT INPUT
[| MONITOR
OUTPUT
COMPUTER
INPUT
MOUSE CABLE
FOR ADB PORT
(PROVIDED) »
MIC VOL
CONTROL PORT (e) ©
OUTPUT
© o
[F]aupio[r] „VIDEO
Mono) EXT. SP (8 Q)
AUDIO CABLE au te
(NOT PROVIDED) COMPUTER
AUDIO INPUT
Set the slide switches as shown in the table below
depending on the RESOLUTION MODE that you want
to use before you turn on the projector and computer.
Sus
SW1- SW6
ON
OFF
NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, monitor, computer,
in that order.
us 49 —

Connecting
an
IBM-compatible
laptop
computer
COMPUTER
COMPUTER
OUTPUT
VGA
CABLE
(PROVIDED)
AUDIO
SERIAL
PORT
PS/2
OUTPUT
INPUT
PORT
INPUT
COMPUTER
INPUT
MOUSE CABLE
FOR PS/2 PORT
(PROVIDED)
| [t MONITOR OUT
o0 ] 60000
o0 000 o
coocoo
MOUSE
CABLE
=
ESE
dE,
enc)
SVILO
FOR
SERIAL
PORT
"7
MW
(PROVIDED)
AEG
*
© o
Haunio VIDEO
(MONO) EXT. SP (8 Q)
AUDIO CABLE
(NOT
PROVIDED)
COMPUTER
AUDIO INPUT
NOTE:
The
hook
up
should
be
done
as
per
the
above
illustration.
After
hook
up,
turn
on
the
projector,
computer,
in
that
order.
—13—

Connecting a Macintosh PowerBook computer
COMPUTER
The Macintosh PowerBook requires the use of the
PowerBook Video Adapter shipped with the PowerBook.
TO POWERBOOK
VIDEO ADAPTER
VGA CABLE
(PROVIDED)
AUDIO ADB VGA/MAC ADAPTER
OUTPUT PORT INPUT (PROVIDED)
COMPUTER
INPUT
MOUSE CABLE
FOR ADB PORT
(PROVIDED)
CONTROL PORT
OUTPUT
VIDEO VIDEO (BNC) S-VIDEO
€ €
(NOT PROVIDED) COMPUTER
AUDIO INPUT
AUDIO CABLE
Set the slide switches as shown in the table below
depending on the RESOLUTION MODE that you want
to use before you turn on the projector and computer.
Sus
13” MODE (640 x 480)
| 16” MODE (832 x 624)
NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector,
computer, in that order.
—14—

|. CONNECTING THE VIDEO EQUIPMENT
CONNECTING TO THE AV INPUT JACKS
Connect to the video and audio outputs of a VCR, video disc player, video camera, satellite TV tuner or other AV
equipment.
e Connect audio/video outputs from external sources to these input jacks using the audio/video cable.
e if the audio signal from the AV equipment is stereo, be sure to connect the right and left channels to the respective right
and left audio input jacks.
€ If the external audio signal is monaural, connect it to the left jack.
€ Do not connect the video sources to the video input jack (RCA TYPE) together with the BNC jack. Use one video input
only for video input jack.
S-VHS FORMAT VCR CONNECTION
The AV input includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has
separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO (RCA TYPE or BNC) jack.
CONNECTING TO THE MONITOR OUTPUT JACKS
These jacks contain the audio/video information of the viewed image.
* Connect audio/video inputs from AV equipment to these output jacks using the audio/video cable.
e If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right
and left jacks.
e |f the audio input of the audio equipment is monaural, connect it to the left jack.
e Whenever the S-VIDEO signal source is viewed on the screen, the video signal available at the MONITOR OUTPUT
jack will be in black and white (monochrome).
—15—

Connecting the Video Equipment
VIDEO EQUIPMENT
Video
Cassette
Recorder
Video
Disc
Player
Satellite
i
TV
Tuner
IigJ
cau
E
E
zm
es
a
L
R
wpgo
VIDEO
AUDIO
OUTPUT
output
OUTPUT
BNC)
VIDEO
COMPUTER IN (MONITOR OUT)
DIIN
Og
S-VIDEO
INPUT
VIDEO INPUT
AUDIO INPUT
AUDIO
INPUT
AUDIO
MONITOR
VIDEO
OUTPUT
MONITOR
OUTPUT
R Speaker (L
VIDEO
INPUT AUDIO S-VIDEO
OUTPUT OUTPUT
IHL—— LI
a sl
; mum
S-VHS VCR
AUDIO SPEAKER
— OUT
L
m0000 Ee
Speaker (R MONITOR
NOTE:
The
hook
up
should
be
done
as
per
the
above
illustration.
After
hook
up,
turn
on
the
projector,
video
equipment,
in
that
order.
=—16—

ERNAL SPEAKER AND MICROPHONE :
| CONNECTING AN EXTE
CONNECTING TO THE EXT. SP. JACK (3.5mm mini stereo type)
This jack contains the audio information of the viewed image. Use it to connect an external speaker system when using
this jack. It will turn off the audio from the internal speaker.
MICROPHONE CONNECTION
The Microphone jack (mini type) is provided with the projector.
* Connect the microphone into the microphone jack.
e Tum the MIC VOLUME control to adjust the microphone volume.
M
COMPUTERIN
MONITOR OUT
00000
e oo o e
MIC
VOLUME
VIDEO
(MONO)
Flaupio[t],
MONITOR OUT AV IN COMPUTER
m
K
EXTERNAL 9
SPEAKERS
SYSTEM
MICROPHONE
—17—

OPERATION OF CONTROLS
© © 60060
TOP OF THE PROJECTOR
TOP
CONTROL
POWER INDICATORS
Light is dim when the projector is on.
Light is brightened when the projector is in stand-by mode.
READY INDICATORS
Light is green when projector lamp is ready to be turned on.
TEMPERATURE WARNING INDICATOR
Flashes red when internal projector temperature is
too high.
LAMP REPLACEMENT INDICATOR
Light is orange when projection lamp 1
is nearing end of service life.
POWER (LAMP) ON/OFF BUTTON
Used to turn projection lamp on or off.
MODE BUTTON
Used to select video source.
(Computer Input or VIDEO Input)
ZOOMFOCUS
VOLUME BUTTONS
Used to adjust volume.
SYSTEM BUTTON
@ Computer Mode
Used to select computer system.
@ VIDEO Mode LEVEL CONTROL BUTTONS
Used to select color system. @ Computer Mode
Used to adjust zoom, focus, brightness, contrast,
SETTING BUTTON horizontal position, vertical position, fine sync and setting
Used to set the auto retract, reverse scan T/B, the auto retract, reverse scan T/B, reverse scan L/R,
reverse scan L/R, blueback and display. blueback and display by pressing + or - button.
@ VIDEO Mode
Used to adjust zoom, focus, color, tint, contrast,
brightness, sharpness and setting the auto retract,
reverse scan T/B, reverse scan L/R, blueback and
display by pressing + or - button.
MENU BUTTON
@ Computer Mode
Used to adjust picture image.
(brightness, contrast, horizontal position, vertical
position and fine sync.)
@ VIDEO Mode ZOOM/FOCUS BUTTON
Used to adjust picture image. Used to select power zoom lens or focus adjust.
(color, tint, contrast, brightness and sharpness.)
NORMAL BUTTON
Used to reset to normal picture adjustment preset by
factory.
af:

866668668
SIDE OF THE PROJECTOR
(COMPUTER IN
cT
MONITOR DUT e
SIG
EJauoio E] FO
NTROEPÓOI co RT,
EI CE
(e) (e) (e)- VIDEO OW) © -VIDEO
(MONITOR OUT)
ALS
AE
| e
t
E
NEZ
vse) Ce
oC
COMPUTER INPUT TERMINAL
Used to connect a computer to the projector.
MONITOR OUTPUT TERMINAL
Used to connect a monitor to the projector.
COMPUTER AUDIO INPUT JACKS
Used to connect a computer audio input to the projector.
CONTROL PORT CONNECTOR
Used to connect a mouse cable to the projector.
MICROPHONE JACK
Used to connect the microphone.
MICROPHONE VOLUME
Used to adjust the microphone volume.
AUDIO INPUT JACKS
Used to connect an audio input to the projector.
OOOO
— 19 —
VIDEO INPUT JACK
Used to connect a video source to the projector.
VIDEO INPUT (BNC) JACK
Used to connect a video source to the projector.
S-VIDEO INPUT JACK
Used to connect a S-VHS video source to the projector.
AUDIO MONITOR OUTPUT JACKS
Permits audio connection to a monitor.
VIDEO MONITOR OUTPUT JACK
Permits video connection to a monitor.
EXT. SP. JACK (3.5 mm mini stereo type)
Used to connect a external speakers system.

OPERATION OF REMOTE CONTROL
This remote control unit can be used not only as a remote control
for the projector operation but also as a wireless mouse for PC.
The remote control unit has a pointing pad and two click buttons.
The wireless mouse function is activated when you do not adjust
the setting by using the MENU operation.
NOTE: To use the wireless mouse function, connect the attached
cable between the projector and your PC since the mouse
control signal is transferred through the projector. Use the
proper cable and follow the instruction as described in
section "CONNECTING THE PROJECTOR?’ on pages 10 ~
14 depending on your PC.
REAR CLICK BUTTON
When in use as a remote for the
projector.
POINTING PAD (POINT BUTTON) This button has different functions
When in use as a remote for the depending on when used. This button is
(9» —. projector. — used to execute the item selected, to
To select an item on the MENU that you increase or decrease the values in
want to adjust. To select an item, move certain items such as COLOR or
CO the arrow by pressing the pad either BRIGHTNESS.
upward or downward.
. . When in use as a wireless mouse
When in use as a wireless mouse _ This button has the same function as
Used to move the pointer. The pointer is the left button in a PC mouse.
moved according to the direction you
are pressing.
FRONT CLICK BUTTON
This button has the same function as
the right button in a PC mouse.
Pressing this button does not affect any
operation when in MENU mode.
ZOOM BUTTONS
Used to operate power zoom lens.
MODE BUTTON
Used to select video source. (Computer
Input or VIDEO Input)
POWER (LAMP) ON/OFF BUTTON
Used to turn the projection lamp on or off.
VOLUME BUTTONS
Used to adjust volume.
FOCUS BUTTONS
Used to operate power focus system.
SOUND MUTE BUTTON
Used to mute sound.
MENU BUTTON
This button will activate the MENU operation.
Use this button, the point button and the rear
click button to make adjustments to the
projector's setting in MENU operation.
o00€
© 80 ©
FREEZE BUTTON
Use this button to freeze on-screen image.
— 20 —