PRYME Radio Products PRYMEBLU BT-583 User manual
QUICK START
1. Connect the PRYMEBLU Radio Adapter to a compatible two-way radio.
2. Pair the PRYMEBLU Radio Adapter with a compatible wireless audio accessory.
3. Connect a wired audio or PTT accessory to the Quick-Disconnect accessory port on the
PRYMEBLU Radio Adapter (optional).
4. Test and use.
STEP ONE: Connecting to Two-Way Radio
To connect your PRYMEBLU Radio Adapter to a two-way radio, follow these steps:
*Always turn o your two-way radio before connecting the PRYMEBLU Radio Adapter.
*Plug the PRYMEBLU Radio Adapter into the speaker-microphone / audio accessory jack of your
two-way radio.
*On some models of two-way radio, you may need to tighten a retaining screw to ensure that the
PRYMEBLU Radio Adapter remains attached to the radio
*Turn on your two-way radio. Because no wireless audio accessory will yet be paired to the
PRYMEBLU Radio Adapter, received signals should be muted.
*The Talk button on the PRYMEBLU Radio Adapter will function as a Push-to-Talk button. However
the internal microphone in your portable radio will be disabled as long as the PRYMEBLU Radio Adapter
is attached. Mic audio will be muted* until a wireless audio accessory is successfully paired to the adapter,
or a wired audio accessory with a microphone is plugged into the Quick-Disconnect port.
2
3 4
PRYMEBLU BT-583 USER’S GUIDE
For Portable Radios with MULTI-PIN
accessory connectors
Bluetooth Adapter
Applicable Models:
BT-537, BT-555, BT-583
Made in Taiwan
FCC ID: N2E-BTM01
Connecting the Adapter to Radio
The PRYMEBLU Adapter allows you to use a compatible wireless
headset or other audio accessory with your two-way radio.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
© 2010-2013 PRYME Radio Products, Brea CA. All Rights Reserved
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting antenna
during transmitting.
RF Exposure Warning!
Please keep product 20cm away from your
body or bystander during the radio operation.
The typical handheld two-way radios were
certied under mobile usage condition
(i.e. keep 20cm away from the user body)
and use of such radio closer than 20cm may
exceed the US RF exposure limit
and shall be avoided.
version 1.3.83 June 2013
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
TOLL FREE: 800.666.2654
WWW.PRYME.COM
STEP TWO: Pairing with an Audio Accessory
* Turn o the radio that the PRYMEBLU Radio Adapter is connected to. Wait at least three seconds.
* Turn the radio on while holding down the Talk button on the PRYMEBLU Radio Adapter.
* Continue to hold the Talk button down for approximately three seconds. Release the Talk button
when the status LED begins to ash two times per second.
* The PRYMEBLU Radio Adapter is now in audio accessory pairing mode. Activate the pairing mode on
your compatible wireless audio accessory.
* Once the wireless audio accessory and PRYMEBLU Radio Adapter are paired with each other, the
status LED on the adapter will show a constant blue light for three seconds.
*If the PRYMEBLU Radio Adapter does not detect a compatible wireless accessory within 60 seconds
of being put into pairing mode, the adapter will exit the pairing mode and resume normal operation.
* Once successfully paired, you will be able to operate your two-way radio using your compatible
wireless accessory.
Reconnecting to a Previously Paired Headset
Once the PRYMEBLU Adapter has been successfully paired to a Bluetooth headset it will remember that
connection. If the headset is powered o or loses connection, the adapter will attempt to reestablish the
connection. The adapter and headset will attempt to reestablish their link whenever when the
radio/adapter and headset are both turned on and in within range of each other. Re-establishing this
connection can take 10-60 seconds.
Pairing With an Audio Accessory
Controls and Connection
Quick Disconnect Accessory Port
Allows the connection of a PRYME QD
series wired audio accessory, such
as a Push-to-Talk, earphone,
or auxiliary microphone.
NOTE: Quick Disconnect Port
is not available on all models.
Radio Connector
This port connects the PRYMEBLU
Radio AdapterAdapter to a compatible
two-way radio.
NOTE: BT-583 Model shown.
Other models may vary slightly
in appearance.
Multi-Function Talk Switch / Status LED
Used to place the PRYMEBLU Radio Adapterin pairing
mode. The LED ashes messages that let the user know
the current status of the PRYMEBLU Radio Adapter.
Once paired with an audio accessory, this switch is used
to activate the Push-To-Talk function of the two-way radio.
BT-537 BT-555 BT-583
6
8
STEP THREE: Using a PRYME Quick-Disconnect Wired Audio Accessory (Optional)
The Quick-Disconnect port on the PRYMEBLU Radio Adapter allows the connection of a compatible
wired PRYME QD series accessory. This includes compatible earphones, surveillance kits, remote
microphones, and Push-To-Talk accessories.
*To connect a wired accessory, rst turn o the two-way radio that the PRYMEBLU Radio Adapter
is connected to.
*Lift up and remove the protective jacket covering the Quick-Disconnect port on the PRYMEBLU
Radio AdapterAdapter to expose the connector.
*Align the Quick-Disconnect connector of the audio adapter with the Quick-Disconnect port on
the PRYMEBLU Radio Adapter and push the connectors together gently until they click into place.
NOTE: the male and female ends of the quick release connectors are keyed so they must be
properly aligned before the two halves can be pushed together.
*To remove a wired accessory that has been installed, gently lift up on the outer cover of the
Quick-Disconnect connector until the accessory is released and then pull up to remove the accessory.
5
STATUS LED MESSAGES
The meanings of the various status LED messages shown by the PRYMEBLU Radio Adapter
are shown on the following table:
TROUBLESHOOTING
My wireless audio accessory will not pair with the PRYMEBLU Adapter.
Follow the instructions to place the PRYMEBLU Radio Adapter into the correct pairing mode
and then activate the pairing mode on the accessory. Make sure that the PRYMEBLU Radio Adapter
Adapter and accessory being paired are within one meter of each other.
My wireless audio accessory or worked before, but is not working now.
Make sure that the PRYMEBLU Radio Adapter is properly connected to the two-way radio
and that the radio is turned on. Ensure that your wireless audio accessory has a fully charged
battery and is turned on. If the devices will still not work, re-pair the PRYMEBLU Radio Adapter
to the wireless accessories..
My radio shows "Keyloader" on the LCD when I press the Talk button of the PRYMEBLU Adapter.
When your press the talk key with no wireless headset paired, the radio believes a keyloader is
attached to the radio. Disable the keyloader function in the radio's programming software or
pair a wireless accessory with the adapter.
7
MEANING
Normal operation
Audio accessory pairing mode active
Successfully paired or re-paired
Radio is turned off
Status LED
* MOTOTRBO SPEAKER MUTING
On Motorola TRBO portable radios with rmware version R.01.07.10 the radio's Aux
buttons may be programmed to unmute the radio's internal speaker. This enables calls
to be received in the event that your Bluetooth headset loses pairing.
SUPPORT AND WARRANTY
PRYME Radio Products warrants this product against defects in materials or workmanship
for a period of one year from the date of retail purchase. PRYME will repair or replace a
defective unit, at our option, without charge for parts or labor. The limited warranty is
extended only to the original purchaser and is valid only to consumers in the United
States and Canada. It does not cover damage or failure caused by or attributable to Acts
of God, abuse, misuse, improper or abnormal usage, faulty installation, improper
maintenance, lightning, or other incidences of excessive voltage, or any tampering or
repairs by other than a PRYME authorized repair facility. It does not cover replacement of
consumable parts, transportation costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms of this
warranty. This warranty can only be modied by an ocer of PRYME Radio Products, and
then only in writing. Should this product prove defective in workmanship or material, the
consumer’s sole remedies shall be such repair or replacement as provided by the terms of
this warranty. Under no circumstances shall PRYME Radio Products be liable for any loss or
damage, direct, consequential, or incidental, arising out of the use of or inability to use this
product. Some states do not allow limitations on how long an implied warranty lasts or
the exclusions or limitations of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specic legal rights.
You may also have other rights, which may vary, from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-2654
or visit us on the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2010 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products. All other
product or service names are the property of their respective owners.
DISCLAIMER: The wireless link used by PRYMEBLU products is an open standard,
unsecured technology. Additionally, this product can mute the portable radios internal
speaker and microphone if used with no wireless or wired audio accessory connected.
This product is not recommended for rst-responder or other mission critical users.
#1 #2Wireless Accessory
Connecting a Wired Audio Accessory
to the PRYMEBLU Adapter
Communications Priority
Audio accessory
connected to Quick
Disconnect Port
NOTE: The Quick Disconnect Port is not available on all models.
™
TM
™
TM
™
TM
™
TM
The Radio Adapterwill mute both the internal microphone and speaker* of your portable radio
if no wireless audio accessory is paired with the device and no wired audio accessory is
connected to the QuickDisconnect port. You should detach the Radio Adapterfrom the radio
when no audio accessory is in use.
STEP FOUR: Transmit and Receive Operation
The PRYMEBLU Radio Adapter will automatically route radio calls based on the following priority:
*If an audio accessory is connected to the Quick-Disconnect Port of the PRYMEBLU Radio Adapter
Adapter, radio calls will be routed to this accessory.
*If no wired accessory is connected, calls will be routed to a wireless accessory, if one is paired
with the PRYMEBLU Radio Adapter.
*If no wireless headset or audio accessory is paired to the PRYMEBLU Radio Adapter or the
wireless accessory is turned o, received calls will be muted* and will not be heard as long as
the PRYMEBLU Radio Adapter is attached to the radio..
NOTE: When a new accessory is connected, paired, disconnected, or powered o, it may take
several seconds for the audio from received radio calls to be routed appropriately.
Push-to-Talk can be activated by any of the following methods:
*Pressing and holding the Talk button of the PRYMEBLU Radio Adapter
*Using the PTT button on a wired PRYME Quick-Disconnect accessory (if one is connected
to the PRYMEBLU Radio Adapter)
* Wirelessly using an optional PRYMEBLU BT-PTT Bluetooth Push-to-Talk
When transmitting, the operator’s voice is picked-up by:
*The microphone in the wired-audio accessory connected to the Quick-Disconnect port on
the PRYMEBLU Radio Adapter.
* If no audio accessory is paired with the PRYMEBLU Radio Adapter, or the paired wireless audio
accessory is turned o, the internal microphone in the attached two-way radio will be muted
as long as the PRYMEBLU Radio Adapter is attached to the radio.
* If no audio accessory is paired with the PRYMEBLU Radio Adapter, or the paired wireless audio
accessory is turned o, the internal microphone in the attached two-way radio will be used.
NOTE: Your PRYMEBLU adapter may mute your two way radio’s speaker*, causing incoming
calls to be missed, in any of the following situations:
* The PRYMEBLU adapter is attached to the two-way radio and no wireless headset or wired
accessory is paired
* Your wireless headset is turned o or runs out of battery power
* Your wireless headset goes out of range of the PRYMEBLU adapter
* Local interference causes the PRYMEBLU adapter and the wireless headset to lose pairing
LED INDICATION
One flash per second
Two flashes per second
One long flash for three seconds
No indication
This manual suits for next models
2
