PureMounts PDS-0001C User manual

TV Floor Cart and AccessoriesINSTALLATION MANUALCAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
PDS-0001C
70"MAX200x200300x300400x200400x400600x40050kg(110lbs)RATED50kg(110lbs)RATEDTVTVDVDDVD5kg(11lbs)RATED5kg(11lbs)RATEDCAMERACAMERA5kg(11lbs)RATED5kg(11lbs)RATED
Maintenance• Check that the bracket is secure and safe to use at regular intervals(at least every three months). • Please contact your distributor if you have any questions.+5°/-12°1200mm1250mm1300mm1350mm1400mm1450mm1500mm1550mm1600mmDisplay panel centerheight measuredfrom floor.--++--++Z11. AdjustmentLoosen the knobs to adjustthe display to the desiredangle and tighten the knobsto secure.

WARNING21NOTE: Read the entire instruction manual before you start installation and assembly.Package Mwasher M-F(x4)M8x20 M-C(x4)M5x14 M-A(x4)M6x14 M-B(x4)big spacer (x4)M-HM6x30 M-D(x4)M8x30 M-E(x4)small spacer (x8)M-G • Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.• Tighten screws firmly, but do not overtighten. Overtightening can cause damage to the items and greatly reduces their holding power.• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.Component ChecklistIMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.PDS-0001Cmiddle base (x1)Aleft leg B(x1)right leg C(x1)left cover D(x1)right cover(x1)Esupport plate (x1)Funiversal plate (x1)G plastic cover (x2)H adapter bracketI (x2)column (x1)Jplastic handle (x1)K top cover (x1)LM6x25 (x2)RM4x6 (x3)SM5x14 U(x2)M4x6 T(x2)M6x14 (x2)Vconnecting plate (x1)Mcamera shelf (x1)NDVD shelf (x1)Owasher P(x4)M6x16 (x8)QM8x25 (x4)XM6x8 (x6)WM5x8 (x2)Yallen key (x1)Zwrench (x1)A1

432. Attaching the Column to the Base QZZZKXZED1. Assembling the BaseCAUTION: Please hold theinner column when looseningthe screws to adjust height.Adjust to the desired height, then tighten all screws.Attach the column to the base using the screws. Tighten all screws using an allen key.• screws. Repeat this step for the left leg.• Each castor can be adjusted independently for fine tuning. Slightly turn the nut to lower or raise the base.Insert the right leg into the base. Align the holes in the right leg to the holes in the base. Secure with theA1

653. Installing the Support Plate4. Installing the Adapter BracketsPIZQWH
min200mm-max400mm
min200mm-max600mmZAttach the support plate to thecolumn with the screws. Tighten all screws using a suitable screwdriver.VLFInsert the washers into the back of universal plate along the plate rails.Insert the adapter brackets into the universal plate. Align theholes in the adapter brackets to the holes in the washers.Insert the four screws but do not tighten them yet.Attach the two plastic covers to both ends of the plate using the appropriate screws.Tighten all screw using a suitable screwdriver.Adjust the adapter brackets to fit the hole pattern of your display. Then tighten all screws with an allen key.NOTE: Verify the proper alignment of all holes.

4-1 For Flat Back Screens TVTVTV 874-2 For Recessed Back Screens or to Access A/V InputsTVTVTVM-A/M-B/M-CM-FTighten all screws but do not over tighten.· Screw the adapter brackets onto the display.Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.orororM-CM-FM-GM-CM-D/M-E/M-FM-GM-D/M-EM-FM-HM-D/M-EM-FM-GM-HY5. Hooking the Display onto the Support Plate· Hook the universal plate onto the support plate.· Tighten two screws to secure them.IMPORTANT: Make sure the display is mounted correctly and that the screws are tightened safely before releasing the display.6. Installing the DVD Shelfplastic holderInsert the two plastic holders of the DVD shelf into the slots and close the lever to lock the DVD shelf.leverTighten two screws to secure.U

7. Cable Management1098. Installing the Camera ShelforSTRWAttach the camera shelf to the connecting plate using appropriate screws. Tighten all screws using a suitable screwdriver.9. Installing the Connecting Plate Attach the connecting plate to the column at the desiredheight using appropriate screws. Tighten all screwsusing a suitable screwdriver.10. Display OrientationA: For Landscape ViewB: For Portrait ViewRemove the two screws to rotate the display 90° clockwise and then retighten the removed screws into the different hole position to secure the display.Install at least two screws diagonally to secure the display.