Puretec ESR2 Series User manual

For correct operation & installation it is essential to observe these instructions.
User Guide
Undersink Drinking Water System with Tripla Mixer Tap
ESR2 - Series With Tripla

2
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
What's inside
Operation...................................................................................................................................... 3
Replacement Guide...........................................................................................................................4
Servicing........................................................................................................................................ 5
Technical Information............................................................................................................ 5
Recommended Working Pressures................................................................................. 5
PART 1 Mixer Tap Assembly
Mixer Tap Installation Guide.............................................................................................. 6
Assembly ...................................................................................................................................... 7
Water Connection Patterns......................................................................................................8
Battery Installation.......................................................................................................................9
Replacement of Ceramic Disc Cartridge(s)................................................................ 9
PART 2 Filter Cartridge Installation
Installation Requirements ......................................................................................................... 10
Installation Procedure.................................................................................................................. 11
Filter Parts Description.................................................................................................................12
Quick Connect Fittings..................................................................................................................12
Cartridge Installation/Changeout .......................................................................................... 13
UV Installation..................................................................................................................................14
Tripla T1 Parts Description............................................................................................... 16
Tripla T2 Parts Description............................................................................................... 17
Tripla T3 Parts Description............................................................................................... 18
Tripla T4 Parts Description............................................................................................... 19
Tripla T5 Parts Description............................................................................................... 20
Tripla T6 Parts Description............................................................................................... 21
Warranty ..................................................................................................................................22-23

3
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Puretec Customer Service
Thank you for purchasing Puretec ESR2-Tripla water lter system. Your system is a
proven performer manufactured from only quality materials and components and will
give years of ‘spring fresh’ water free of impurities if maintained properly.
The Puretec ESR2 system cartridges need replacing regularly to maintain optimum per-
formance. This is a simple procedure when following instructions. For cartridge replace-
ments contact your nearest Puretec stockist.
The system is designed for metropolitan supply water but can be used in other situa-
tions. For other types of water supply please contact your local Puretec stockist or call
our Puretec Customer Service Helpline prior to installing the tap.
Customer Service Helpline 1300 140 140 (Australia) 0800 130 140 (New Zealand)
Caution: Do not use with water that is microbiologically unsafe or with water of unknown
quality without adequate disinfection before or aer the system. This product must be
installed in accordance with local plumbing regulations by a licensed plumber.
Operation
The Puretec ESR2-Tripla system is designed to run economically for many years and this
is dependant on the initial installation and periodical maintenance.
Flush systems for 10 minutes aer any period of non-use more than 2 days. For a pe-
riod of non-use of 2 weeks or more, it may be necessary to replace cartridge.
Chrome Plated Surface - should only be cleaned with liquid detergent or soap and water.
Under no circumstance should any abrasive or acid base cleaning agents be used.

4
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
Replacement Guide
To maintain the high quality of the puried water the cartridges need changing every 6
months (this is dependant on water quality and usage).
You can obtain replacement cartridges and/or lamp from your local Puretec dealer and
to maintain performance and warranty use genuine Puretec replacements.
A B C
ESR2 PL051 MC011-S RL2
Replace cartridges every 6 months. Replace all RL coded
products every 12 months.
Other cartridges are available to suit a range of requirements upon request.
Important note: When replacing cartridge, ensure you reset the LED reminder light by re-
moving/replacing the battery from the rubber seat. Please refer to page 7 for a detailed
diagram.

5
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Servicing
Periodically clean the aerator for any lodged sediment that may restrict ow. A Puretec
water lter is highly recommended for product longevity.
Should it be necessary to have your mixer serviced while under warranty, please carry
out the following procedure:
1. Firstly call the plumber, preferably the one that has installed it, (most problems
are caused by the supply lines not being cleaned out properly, prior to connecting
the mixers).
2. Make sure that the plumber has installed your mixer according to the Instruction
Guide.
3. If the plumber is satised that he cannot rectify the problem then contact your
plumbing supply store or your local Puretec stockist.
Important: We do not recommend the dismantling of any internal part of the mixer
purely to see what is inside as this will breach your warranty.
Technical Information
Puretec mixers can be used in conjunction with:
• Pressure storage hot water system
• Any mains water pressure not exceeding 500 kPa
• Maximum hot water temperature of 60°C
• Instantaneous hot water system
Recommended Working Pressures
• Minimum working pressure 50 kPa (7.5 PSI)
• Maximum working pressure 500 kPa
It should be noted that water mains pressure builds up during o peak periods, mainly
at night, sometimes doubling or trebling normal daytime pressures.
Note: Not suitable for unequal pressure. On high pressure areas where the pressure
exceeds the recommended working pressure as indicated above pressure limiting valves
must be installed or warranty is voided.

6
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
HOT
Mixer Tap
Rubber Washer
Sink Faucet
Hole (Ø33mm)
Water Fiter
COLD
Metal Washer
Rubber Washer
Locking Nut
Retainer Screw
Metal Pipe
Mixer Tap Installation Guide
Note: It is important to ush out the supply pipes to the mixer
before connecting the exible hoses, with the initial installation, so
no foreign matter can enter into the cartridges.
A Puretec Water Filter is highly recommended for product longevity.

7
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Step 4. Place the retainer screw
through the hole in each spacer and
screw to the hole on the bottom of
the faucet.
Then, use a wrench to lock the
retainer nut.
Rubber Spacer
Locking
Nut
Retainer Screw
Zinc Spacer
Assembly
O-Ring
Brass Base
1
2
Step 1. Connect the hoses to the
faucet and tighten them.
Only use hand to screw the exible
hose. Do not over tight. Don't use any
tools.
Step 2. Put brass base with o-ring to
the bottom of the faucet.
Basin or Sink
33mm dia.
Hole
Step 3. Put the hoses through the
basin or sink. Required through hole
size is Ø33mm.

8
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
Retainer
Screw
HOT Water
Connection
COLD Water
Connection
Water Filter
Connection
For TRIPLA T1 & T2
Water Connection Patterns
Retainer
Screw
HOT Water
Connection
COLD Water
Connection
Water Filter
Connection
For TRIPLA T3 to T6
Retainer
Screw

9
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Battery Installation - LED reminder light
1. Remove the black battery seat from the
faucet canopy
2. Install battery into the battery seat,
positive side up.
Note: red light ashes
twice and then followed
by the blue light
3. Reinstall battery seat assembly into the
faucet canopy
Important note: Battery must be replaced when changing cartridges.
5. Red light ashes indicates your cartridges
are due to be changed (usage has
exceeded 3,000 minutes or 12 months).
Please change the battery when
changing the lter cartridge(s).
Positive
side up
Negative on
the PCB
4. Blue light ashes during
normal operation.
Replacement of Ceramic Disc Cartridge(s)
1. Hot/Cold Outlet
• Remove hot and cold water indicator then release screw in lever and li lever o,
now you can unscrew dome cap and loosen the cartridge lock nut.
• Li out old cartridge and clean inside making sure no old O-rings are still stuck
inside cartridge housing.
• Insert new cartridge making sure O-rings on bottom of new cartridge have not
fallen o and lugs in bottom of cartridge line up with holes in cartridge housing.
• Now you can tighten lock nut with a torque wrench to 14 newton meters, then
reinstall dome cap, lever screw and hot and cold water indicator.
2. Filtered/Rain Ancillary Outlet
• Remove front button cover using ne-edged 1.2mm screwdriver.
• Unscrew handle then remove cartridge by unscrewing it anti-clockwise, using 5/8”
socket. Install cartridge by completing removal instructions as above, in reverse
order.
• Ensure cartridge is rmly tightened not over tightened.

10
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
Filter Cartridge Installation
This system comes complete with an installation kit enabling it to be connected to
15mm (½”) copper pipe (Cold supply only - hot water should be ltered prior to heating).
This product must be installed in accordance with local plumbing regulations by a
licensed plumber.
Installation Requirements
• 15mm (½”) Cold water line.
• Power supply: 240 VAC.
• Supply pressure: 300-875 kPa. Install pressure limiting valve if pressure exceeds
875 kPa.
• Supply temperature 3°C - 52°C.
• Suitable spot for faucet.
• Alternative ttings may be required if being connected to anything other than
15mm (½’) copper pipe.
• Caution: Do not use with water that is microbiologically unsafe or of unknown
quality without adequate treatment before or aer the system.
Application warning; minimum water characteristics must be met before
installation of Radre™ to ensure proper operation and continuous protection.
Iron less than 0.3 mg/L
Hydrogen Sulphide less than 0.05 mg/L
Suspended Solids less than 10 mg/L
Manganese less than 0.05 mg/L
Hardness less than 110 mg/L
Hy

11
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Installation Procedure
1. Select suitable location that is close to the point of ltered water delivery (eg.
sink). Remember to allow access room for changing lters and a suitable place
where water spillage will not cause damage. Location should not be in direct
sunlight.
2. Isolate water supply and install adaptor ballvalve.
3. Choose the best position for the faucet, taking into consideration height of jugs
etc. and also the drainage of any spills. Then drill a 12mm hole and install the
faucet as in step 5.
4. To install faucet, place the small rubber washer, chrome washer and large rubber
washer on to the threaded end of the faucet (see gure 3 for detailed connection).
Insert the faucet into the hole in sink or bench. Slip the large plastic washer and
lock washer onto threaded end of faucet and screw on nut and tighten making
sure faucet is correctly positioned on top. See page 7 for LED battery installation.
5. Install the lter housing assembly by positioning it in the desired location, marking
the position of xing holes and xing with mounting screws. Allow room for the
connecting tubes and for removing the lter bowls (50mm).
6. Fit tubing into adaptor ballvalve to the lter and lter to the faucet (see g. 2 on
how to use quick-connect ttings). Allow slack in the tubing. Make sure ow is right
according to inlet outlet on housing assembly.
7. Install cartridges as per cartridge installation/replacement on page 8.
8. Install UV lamp as per UV lamp installation/replacement on page 9.
9. Restore the water supply and check for leaks. The lters need to be only hand
tight. If they leak then undo housing and check the O-Ring is seated properly.
10. Run the system for at least 10 minutes (turn the faucet lever to the upright
position) to remove carbon nes. Water may appear milky, but this is normal and
is only tiny air bubbles that will clear aer a short period.

12
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
No. Description
1 Adaptor ballvalve
2 Flexible tubing
3 Filter assembly
4 Mounting bracket
Figure 1
7
6
5
3
24
8
1
1. Cut the tube square and push in to the tube
stop. For metal tube remove burrs and cham-
fer tube end to prevent O-Ring seal being
damaged.
DISCONNECTION PROCEDURE
4. Push collet against body and slide tube out of
tting.
2. Fitting grips before it seals. Ensure tube is
pushed in to tube stop.
HOW TO USE QUICK CONNECT FITTINGS
3. Tube is secured in position.
Figure 2
5 Flexible tubing
6Tube, nut and ferrule
(see separate breakdown on g. 3)
7 LED Faucet
8 UV module (ESR2 model only)

13
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Cartridge Installation / Replacement
To change the lter cartridges adhere to the following procedure.
1. Turn mains water supply o.
2. Relieve water pressure by operating faucet lever.
3. Unscrew Filter Housing using the spanner wrench and discard cartridges. When
removing housings place a container underneath to catch any spillage.
4. Cleanse the inside of the housing using hot water and detergent. Check O-Ring
and lubricate with food grade silicone lubricant (or similar). Replace O-Ring if
kinked or damaged. (PN: FPOR).
5. Install new cartridges and replace housing screwing them up HAND TIGHT ONLY.
Sediment lter is on the inlet side and chemical on the outlet side.
6. Restore water supply & check for leaks, rectifying them, if any, before leaving the
unit.
Aer installing cartridges ush unit for 5 - 10 minutes.
Cleaning Quartz Sleeve
To ensure high sterilizing rate with best water quality, check sleeve regularly (about
every 3 months depending on quality of water source). To see whether there is dirt or
substances gathered. Clean with alcohol based cleaner if necessary.
Quartz Sleeve Maintenance Procedure
1 Unplug the power supply. Remove UV lamp before taking out the quartz sleeve
and pour out water. Turn counterclockwise the aluminium nut both sides of the
chamber and extremely gently to remove the quartz sleeve.
2 Soak a piece of cloth in vinegar or citric to clean the quartz sleeve.
3 Put the quartz sleeve back into the stainless steel chamber and make equal
distance at both sides of the chamber.
4 Dampen the seal O-Ring and end of the quartz sleeve then turn clockwise the
aluminium nuts with hands tightly.
5 Check all connection to prevent leakage.
6 Insert UV lamp into stainless steel chamber and put on the rubber cap to complete
the cleaning.

14
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
Figure 4
UV Lamp Installation / Replacement
• Prior to performing any work on the steriliser, always disconnect the power supply
rst.
• Do not look directly into ultraviolet rays emitted from the UV lamp as they will
cause serious burns to unprotected eyes.
• This treated water will seem warm at rst ow for a short period when it is not
used, as the lamp creates heat; you can ush before use.
User Guide 4
Aluminium
Nut
Water
In/Outlet
O-Ring Lamp Power
Connector
Quartz
Sleeve UV lamp
Aluminium
Nut
Rubber
Cap
Ballast
Stainless Steel
Chamber
1. Turn aluminium nut clockwise to x the quartz position (default setting from
manufacturer, see g. 4).
2. Insert UV lamp into chamber through the hole of the aluminium nut end. Never
touch the quartz (glass) and lamp surface as spots of ngerprints may interfere
with UV transmission. If lamp is dirtied, please clean lamp with alcohol based
cleaner.
3. Put rubber cap on the aluminium nut end to complete the assembly.
4. Plug in power connector with ballast and make sure that the LED is illuminated
steadily to start operation. This should be all carried out by relevant qualied
tradesmen.
Note: For initial use, wait 3-5 minutes to allow water to pass through the whole
unit. Turn on point of use to let water ow through the unit for 2-3 minutes to release air
and impurities from system.

15
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
Tripla Parts Descriptions

16
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
TRIPLA T1 Parts Description
2. screw
3. screw
5. handle
1. handle
10. Teflon washer
10. Teflon washer
28. washer
34. regular seat
38. handle cap
41. battery seat
31. EPDM washer 12. EPDM washer
12. EPDM washer
13. EPDM washer
29. aerator insert 32. aerator insert
30. aerator cap
33. aerator cap
16. rubber washer
15-2 nut
19. rubber
washer
20.
stainless
washer
21. brass
nut
18. screw
35. screw
39. display
9. cover stem
7. plunger
11. spout
11-1 body
14. body stem
15-1 body
11-2 tube
11-3 inner tube
11-4 connector
4. cap 6. cap
8. stem / cartridge
45. flexible
tube ½”
inlet/outlet
hose
17. housing
36. magnetic seat
40. circuit board
37. magnet
38. O-ring

17
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
TRIPLA T2 Parts Description
18. brass nut
17. stainless washer
1. Screw
3. Handle
8. Teflon washer
8. Teflon washer
10. EPDM washer
25. EPDM
washer 28. EPDM
washer
11. EPDM washer
10. EPDM washer
14. EPDM washer
16.
rubber
washer
15. Screw
9-1. body
39.
handle
cap
37.
screw
36. Display
32. Screw
31. Plunger
33. Magnet seat
34. Strong magnet
35.
Handle
cap
7. Cover stem
12. Body Stem
38. O-ring
41. Battery seat
40. Circuit board
5. Plunger
9. Spout
2. Cap 4. Cap
6. Stem / cartridge
42. flexible tube ½”
44. flexible tube ½”
44. flexible
tube ½”
13-1. Body Stem
13-2. Body Stem
9-2. brass tube
9-4. connector
9-3. inner tube
26. Aerator
insert 29. Aerator
insert
27. Aerator
cap 30. Aerator
cap

18
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
TRIPLA T3 Parts Description
7. handle
10. handle cap
23-4 connector
33. handle
8.
screw
34. canopy
47. wrench
4. washer
25. washer
38. housing
5. aerator insert
39. o-ring
6. aerator cap
9. display
41.
washer
42.
washer
43.
brass
nut
8. screw
40. screw
26. O-ring
23. spout
28. body
35. body
36. nut
23-3 inner tube
23-2 tube
11. screw
24. cap
44. flexible tube
1. washer
2. aerator
insert
3. aerator cap
23-1 body
27. O-ring
29. o-ring
30. connector
30-2. cartridge
31. plunger
32. cap
37. stopper
12. strong
magnet
14. battery
seat
15. circuit
board
13. magnet seat

19
Copyright © Puretec Pty Ltd 2015 Puretec Tripla™ | Triple Action Tapware
42.
washer
43.
washer
44.
brass
nut
41. screw
45. flexible tube
TRIPLA T4 Parts Description
1. spout
1-3. inner tube
1-4. connector
2. washer
3. aerator insert
1-2. tube
1-1. body
5. gasket
4. aerator cap
6. washer
7. O-ring
8. O-ring
9-1. washer
9-2. gasket
9-3. gasket
28. screw
35. handle
36. screw
37. handle cap
29. body
38-1. body
38-2. nut
30. O-ring
31. connector
32. stem
33. plunger
34. cap
39. stopper
40. washer
17. circuit
board
10. cap 13. display
16. screw
11. O-ring
12. screw
15. washer
21. plunger
22. turn stem body
23. stem post
24. upper
25. lower
14. handle cap
18. battery
seat
20. magnet
seat
19. strong
magnet
26. seat
27. stopper
26. seat

20
Installation & Operation Manual Copyright © Puretec Pty Ltd 2015
TRIPLA T5 Parts Description
42.
washer
43.
washer
44.
brass
nut
41. screw
45. flexible tube
1. spout
1-3. inner tube
1-4. connector
2. washer
3. aerator insert
1-2. tube
1-1. body
5. gasket
4. aerator cap
6. washer
7. O-ring
8. O-ring
9-1. washer
9-2. gasket
9-3. gasket
28. screw
35. handle
36. screw
37. handle cap
29. body
38-1. body
38-2. nut
30. O-ring
31. connector
32. stem
33. plunger
34. cap
39. stopper
40. washer
17. circuit
board
10. cap 13. display
16. screw
11. O-ring
12. screw
15. washer
21. plunger
22. turn stem body
23. stem post
24. upper
25. lower
14. handle cap
18. battery
seat
20. magnet
seat
19. strong
magnet
26. seat
27. stopper
26. seat