Putorsen TWM69-446 User manual
MEDIUM FULL-MOTION TV WALL MOUNT
TWM69-446
www.putorsen.com
Thank you for choosing our product! Our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts or
a brand-new product to ensure you have a fully functioning product.
Would you kindly share your experience on Amazon if you are satisfied?
WARNING!
Tools Needed (Not Included)
Supplied Hardware
A (x1)
Wall Mount
B (x2)
Mounting Bracket
C (x1)
Bubble Level
D (x1)
Wrench
E (x4)
Hook and Loop Fastener
1
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any
of the instructions or warnings, please contact your local distributor for assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious
personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals.
This product is designed to be installed only on solid concrete walls or brick walls.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached
hardware and components.
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
MAINTENANCE:Check that the bracket is secure and safe to use at regular intervals (at least every three months).
M-A (x4)
M5x14 Screw
M-E (x4)
M8x50 Screw
M-F (x4)
Two-Hole Washer
M-G (x8)
Spacer
M-H (x8)
Spacer
M-B (x4)
M6x14 Screw
M-C (x4)
M6x30 Screw
M-D (x4)
M8x30 Screw
W-A (x4)
ST6.3x55 Lag Bolt
W-B (x4)
Ø10x45 Anchor
W-C (x4)
Lag Bolt Washer
Socket wrenchScrewdriver
2
Before TV Bracket Installation
2.95 in. 3.94 in.
11.81 in.
7.87 in.
15.75 in.
NOTE: Read the entire instruction manual before you start installation and assembly
Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation
sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
Please note: Images in these assembly instructions are only technical presentation of the product. Actual product
design may vary minimally.
This product was designed to be installed and used ONLY as specified in this manual. Improper installation of this
product may cause damage or serious injury.
This product may only be assembled / installed by the technical staff.
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached
hardware and components.
When mounting on the wooden beams wall, make sure that the fastening screws are anchored in the center of the
beams. It is highly recommended to use a beamfinder.
Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
Tighten screws firmly, but do not over tighten. Over tightening can cause damage the items, this greatly reduces
their holding power.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
By reason of large television construction types on the market, we can’t adjust our screen installation materials for
each screen type. Therefore it is possible that the screws which are numerously delivered don’t fit with your TV/Monitor.
We ask for your understanding that we can’t cover up all possibilities of many screen types.
Each wall is built up of different materials which can result a special requirement. Therefore we are concentrated on
the delivery of installation materials only for mass concrete walls. Use our included installation accessories only
for mass concrete walls.
If your walls have a special demand of materials, we advise you to ask in an expert shop for a suitable acquirement
of the installation materials.
Make sure that before and after the installation of the product neither you nor somebody else can be injured and
other objects can be damaged. In case of doubt request for help from an expert.
Make also sure that you and optionally the co-helper or representatives have registered the mounting instructions
before the installation and also the warning notice.
3
Step 1 Installing the Wall Mount
1. Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (C) to ensure the
wall mount (A) is level.
2. Use a 3/8 in. (10mm) drill to slowly drill 2.4 in. (60mm) pilot holes.
3. Insert anchors (W-B) into the holes. Ensure the anchors are completely flush to the concrete surface even if
covered by a layer of joint compound or other material.
4. Attach the wall mount (A) to the wall using the lag bolts (W-A) and lag bolt washers (W-C).
CAUTION: Ensure the wall you select is a
weight-bearing wall. Failure to observe this
precaution can result in serious physical
injury and/or property damage. Consult a
professional installer or contact customer
service if you have any questions.
CAUTION: Avoid drilling near electrical
wiring and water pipes.
CAUTION: Do not drill into mortar between
bricks or into loose concrete.
CAUTION: Never drill into hollow bricks.
Attaching Brackets to TVs with Flat Backs:
Using the two-hole washers (M-F) and screws (M-A or M-B) as shown.
Attaching Brackets to TVs with Curved or Recessed Backs:
Using the two-hole washers (M-F) and screws (M-C or M-D) and
spacers (M-G, M-H) as shown.
Hang the TV on the wall mount (A) and tighten the screws on the bottom of
the mounting brackets (B) as shown to secure the TV.
HEAVY! You will need
assistance with this step.
4
Step 2 Attaching Mounting Brackets to the TV
CAUTION: Tighten the screws so the brackets
are firmly attached. DO NOT OVERTIGHTEN.
This may damage your TV.
Step 3 Attaching the TV to the Mount
±60°
+3°
-12°
Route cable along the arm using the Hook and Loop Fastener (E).
Tilt: Using the wrench (D) to loosen or tighten the screws on the VESA
plate as shown.
Leveling: Using the wrench (D)
loosen or tighten the screws on
the VESA plate as shown.
5
Step 4 Cable Management
Step 5 Adjusting the TV to the Desired Position
±3°
6
7
Table of contents
