PX B52Q Series User manual

- 1 -
WIFI Bike & Motor Cam
(Motor Accessory)
User’s Manual
B52Q Series

- 2 -
Table of Contents
1. Precautions before Use
2. Introduction
3. Features
4. Package Content
5. Notice for First time use
6. Installation
7. Product Appearance
8. Quick APP Installation Guide
9. APP UI Description
10.Trouble Shooting
11.Specification
12. Series Difference
13. FCC Statement

- 3 -
Precautions before Use
Recording Mode
(1) Once the system is powered on, it will enter loop recording
mode. (The recording LED is flashing).
(2) To exit the loop recording mode, please stop recording first
Press [Loop] key Press Start Recording.
Now, it’s normal recording.
(The recording LED is ON permanently)
Formatting your SD Card
Long press [Loop/WIFI] key for 8 sec, system will response with
5 sec’s Continuous beep sound.
Press the Snapshot key within 5 sec. will start formatting your
SD card.
Before formatting, please put your system into standby mode.
(Stop recording .)
After SD card formation, system will enter standby mode .
Please restart the system.
Restore to Factory Default
Long press [Loop] key for 20 sec., system will prompt with
continuous beep sound for 5 sec. Press [Snapshot] key
within 5 sec., the system will restore to factory default settings.
Hot key for File Backup
Long press [Snapshot] key for 2 sec., the system will back up
the previous and current recording files to your Backup folder in
the SD card.

- 4 -
Definition of Recording Space
(1) SD card space used by current recording mode. Normal
recording will force deleting loop recording space when the
space is not enough for its operation. When this happened,
system will display warning LED and sound for the insufficient
memory space.
(2) Loop recording cannot delete other files on the memory card.
It can only delete older loop recording files to make room for
the current recording.
(3) If use a brand-new memory card in loop recording, the whole
SD card space can be used for loop recording.
(4) When SD card is full while in loop recording mode. If you stop
recording and try to start normal recording again.
Then system will delete older loop recording files to make
space for the normal recording.
Suppose a 16G SD card is used for the system, it can save
video files for around 120 min.
Eg. 1: For loop recording only, it can save video files for 120 min
and can do the loop recording continuously.
Eg.2 : For normal recording only, it can save video files up to
120 min, then the “could not recording” LED and warning sound
will prompt by the system. You need to replace the SD card in
order to continue recording.
Eg. 3: If you loop recording for 100 min, then do a normal
recording for around 100 min. Under this case, the system
will use the left 20 min for the normal recording, then delete
older loop recording files total of 80 min to make room to do the

- 5 -
normal recording.
Introduction
B62G is a Camera specialized for Bike & Motor. It equips
with water proof ability, anti-shake and share functions
using WiFi.
Features
Anti-Shake(EIS + Stable Construction)
Water Proof Mechanical (IPX5)
One hot key to back up file to system and smartphone.
Quick release lock design, with Screw & Quick Release
installation
HD Video Record (1080@30)
Support loop / normal recording
WIFI Transmission for files browsing and sharing.
Controls Record/Snapshot/File Browsing/File Sharing via
APP
1 Hours continuous recording
100% Recording Successful Rate
Warning for error of SD Card
APP available
Low wind resistance, wind diversion design
Video Noise Reduction
Auto Date/Time Correction via APP
Quick Snap Shot button
Snap Shot while recording Simultaneous
WDR Technology
Video & Trail Player in PC

- 6 -
Package Content
< Main unit >
Main unit Handle Bar Holder
Adjusting arm Quick Release Lock Base &
screw
Adhesive Mount Universal Mount
Charging Cable User Manual

- 7 -
< Rear Cam >
Rear Cam
Adjusting arm 3M Extension cable
Adhesive Mount Universal Mount
< B-GPS >
B-GPS

- 8 -
Notice For First-Time Use
(1) Please read this manual before using the system. Make sure
the content of the package is complete. If there is anything
missing or damaged, please contact the original dealer right
away.
(2) Please use SD card with Class 10 8GB or above. (The system
can support up to 32GB)
(3) This product does not guarantee to be compatible with all brands
of SD card.
(4) Don’t remove the SD card during recording. Please turn off the
system then remove the SD card. Improper operation will
damage your SD card or cause data lost.
(5) Pro-long operation may cause temperature rise of the Bike cam.
This is normal, no need to worry and use it as usual.
(6) Please don’t repair the system yourself. When it needs repair,
please contact your dealer or our Customer Service Department.
NCC Warning
Article 12 Low-power radio-frequency motors qualified by type
approval shall not change frequency, power or alter the
characteristics and functions of the original design without
permission.
Article 14 The use of low-power RF motors shall not affect the safety
of air navigation and interference with legitimate communications.

- 9 -
Installation
<main unit >
Insert Memory Card.
* Ensure SD Card is inserted in correct direction
* Use only microSD SDHC C10 or higher level
* 8G or higher capacity SD Card recommended
Install Quick Release Lock Base

- 10 -
Install Handle Bar Holder
360 Rotatable Holder mount

- 11 -
Install Adhesive Mount
Install Universal Mount

- 12 -
< Rear Cam >
Install Handle Bar Holder
Blue LED
lights up

- 13 -
Install Adhesive Mount
Install Universal Mount

- 14 -
Install Universal Mount & Adjusting arm

- 15 -
< B-GPS >
Installation diagram
Installation position
GPS LED flashing
When Positioning
Successfully

- 16 -
Bicycle tube holder
Extended interface
Hand screw
Host & Quick
release base
GPS Receiver
Handle Bar Holder
GPS Plug
Handle Bar

- 17 -
Motor side mirror holder
Host & Quick
release base
GPS Plug
Side mirror holder
GPS Receiver
Hand Screw
Extended interface
Side mirror

- 18 -
Motor adhesive holder
Flat place
Host & Quick
release base
GPS Plug
Side mirror
holde
r
GPS Receiver
Hand Screw
Extended interface

- 19 -
Motor Universal mount
GPS Plug
Host & Quick
release base
Universal mount
GPS Receiver
Hand Screw
Extended interface

- 20 -
Computer program Interface
Computer program name：GVPlayer
Program download area：
1) Trans website download
area(http://www.px.com.tw/file/B52%20video.rar)
2) https://drive.google.com/open?id=0B7GBHEgWCJt0SDR0Ty01
U2J0S1U
Instructions：
- To provide the use of the GPS function recorder.
- When using this function, the computer must be connected to the
Internet.
- After the map function is turned on, the information in the window
will be updated with the video playback.
- The GPS information above provides the user with the
coordinates and speed information.
Video Play
Files Group List
Map
Tracker
Files List